1999 DODGE RAM heater

WARNING: Vehicle interior will contain sodium hydroxide powder, a
by-product of air bag deployment. Since this powder can
irritate skin, eyes, nose, or throat, be sure to wear
safety glasses, rubber gloves and long-sleeved shirt
during clean-up.
1) Begin clean-up by putting tape over air bag exhaust vent,
so no additional powder will escape into vehicle interior. Remove air
bag modules. Use a vacuum cleaner to remove any residual powder from
vehicle interior. To avoid kneeling or sitting on a non-cleaned area,
clean from outside vehicle and work your way inside.
2) Remove any residual powder from A/C-heater outlets. Turn
blower motor to low for a few minutes and exit vehicle. Turn blower
off. Vacuum any additional powder expelled from plenum. Vacuum
interior a second time to recover all powder.
DEPLOYED AIR BAG
Dispose of deployed air bag module as any other part. No
special disposal procedure is required.
UNDEPLOYED AIR BAG
NOTE: Information on passenger-side air bag deployment is not
available from manufacturer.
Procedure 1: In-Vehicle Deployment (Driver-Side Air Bag)
1) Use this procedure if scrapping a vehicle with an
undeployed air bag. This procedure assumes that air bag wiring is
intact.
2) Disconnect and shield negative battery cable. Disconnect
2-pin clockspring at base of steering column. Cut 2-pin clockspring
connector of at clockspring side of harness.
3) Strip 1" (25 mm) of insulation from wire ends. Make a
harness consisting of 2 wires 20 feet or longer. Connect 20-foot wires
to clockspring harness. Ensure there are no loose parts in passenger
compartment and no one is within 20 feet of vehicle.
4) Staying at least 20 feet away from vehicle, connect other
2 ends of 20 foot wires to terminals of a 12-volt battery. When
deployment is achieved, loud bang will be heard and air bag will
inflate. After air bag module deploys, let module cool and dust settle
before approaching. If air bag fails to deploy, go to PROCEDURE 2.
Procedure 2: Remote Deployment (Driver-Side Air Bag)
1) Use this procedure if scrapping a vehicle with a live air
bag, but a problem in electrical system prevent deployment with air
bag still installed in vehicle. Also use this procedure if PROCEDURE 1
was unsuccessful.
WARNING: Perform remote deployment outdoors. Never attempt to deploy
air bag module inside a building, within 20 feet of
personnel, or with air bag trim cover face down.
2) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Remove air bag
module. See DRIVER-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION.
3) cut pigtail wiring harness between clockspring and air bag
as close to clockspring housing as possible. Reconnect other end of
pigtail harness back into air bag module.
4) Strip 1" (25 mm) of insulation from cut ends of harness.
Place air bag module face (trim cover) up. Connect two 20-foot wires
to end of harness wires. Move 20 feet away. Connect other end of 200-

Fig. 3: Locating Intercooler & Components
Courtesy of Chrysler Corp.
8) Ensure connections on both batteries are tight and not
corroded. Ensure the three 32-pin connectors are fully engaged on
Powertrain Control Module (PCM). PCM is located on firewall at
passenger's side rear corner of engine compartment.
9) Check for loose, defective or corroded connections at
intake manifold air temperature sensor. See Fig. 4.
10) Ensure electrical connections on intake manifold air
heater relays and intake manifold air heater are tight and not
corroded. Intake manifold air heater relays are mounted on inner
wheelwell, below driver's side battery. See Fig. 5. Intake manifold
air heater is located between air inlet housing and intake manifold
cover. See Fig. 6.

Fig. 5: Locating Intake Manifold Air Heater Relays
Courtesy of Chrysler Corp.

Fig. 6: Locating Intake Manifold Air Heater
Courtesy of Chrysler Corp.
NOTE: Restricted low-pressure fuel lines from fuel tank to fuel
transfer pump, fuel heater and fuel filter/water separator
may cause starting problems and prevent engine from
accelerating. Restricted high-pressure fuel lines from fuel
injection pump to fuel injector may cause starting problems,
poor engine performance and excessive Black smoke.
11) Check all fuel supply and returns lines for damage,
kinking or leakage. Check throttle linkage for binding. Check for a
stretched or disconnected throttle return spring.
12) Ensure all ground connections are tight and free of
corrosion. Ensure accessory drive belt is not damaged or slipping.
Check for loose or defective electrical connection on Crankshaft
Position (CKP) sensor. See Fig. 1.

13) On A/T models, ensure all electrical connectors are clean
and properly connected to electrical plugs on transmission case. On
all models, check for loose or defective electrical connections on
starter and starter solenoid.
MECHANICAL INSPECTION
Compression
Manufacturer does not provide information for checking
compression.
FUEL SYSTEM
AIR IN FUEL SYSTEM
NOTE: Air in the fuel system may cause hard starting, rough
running, excessive smoke, poor engine performance, engine
misfire, poor fuel economy and fuel knock. Air may enter fuel
system whenever fuel supply lines, fuel filter/water
separator, fuel injection pump, fuel injectors or high
-pressure fuel lines are removed or disconnected.
1) Inspect all low-pressure fuel lines from fuel tank to fuel
transfer pump, fuel heater and fuel filter/water separator for signs
of leakage. Inspect all high-pressure fuel lines for signs of leakage.
See FUEL INJECTOR & HIGH-PRESSURE FUEL LINES under FUEL SYSTEM.
2) After repairing fuel leak, bleed air from fuel system. See
FUEL LINE BLEEDING under FUEL SYSTEM in REMOVAL, OVERHAUL &
INSTALLATION - TRUCKS - DIESEL article.
FUEL HEATER
1) Fuel heater is located in fuel filter/water separator. See
Fig. 1 . Fuel heater uses a fuel heater temperature sensor for
controlling operation of the fuel heater.
2) A defective fuel heater may cause excessive wax build-up
in the fuel filter/water separator during cold ambient temperatures.
Wax build-up may cause hard starting, prevent engine from
accelerating, low power, Blue smoke or White smoke. For testing of
fuel heater and fuel heater temperature sensor, see SYSTEM & COMPONENT
TESTING - TRUCKS - DIESEL article.
FUEL HEATER RELAY
Ensure fuel heater relay, located in power distribution
center is installed correctly and that terminals are not corroded. For
fuel heater relay testing, see SYSTEM & COMPONENT TESTING - TRUCKS -
DIESEL article.
FUEL FILTER/WATER SEPARATOR
NOTE: A blocked or restricted fuel filter/water separator may cause
starting problems, prevent engine from accelerating, low
power or White smoke. If an excessive amount of water
collects in filter/separator in a short period of time, it
may be necessary to drain and clean fuel tank.
1) When ignition switch is first turned to ON position,
WATER-IN-FUEL (WIF) warning light should come on for 2 seconds to
perform bulb and wiring circuit test and then go off. WATER-IN-FUEL
(WIF) warning light is located on instrument panel, just below the

NOTE: A leaking fuel injector or high-pressure fuel line may cause
a rough idle, Black smoke, poor engine performance, poor fuel
economy and fuel knock. Since a leaking high-pressure fuel
line may cause the same symptoms, check for leaking high
-pressure fuel line before checking fuel injector.
1) To determine which injector or line is malfuntioning,
start engine and check each cylinder output using scan tool. If scan
tool is not available, start engine and engine allow to idle. Loosen
high-pressure fuel line nut at each fuel injector in turn and listen
for a decrease in engine speed. Tighten high-pressure fuel line nut to
30 ft. lbs. (40 N.m). Go to next step.
2) To check for a leaking high-pressure fuel line, start
engine and allow engine to idle. Inspect high-pressure fuel lines and
connections for signs of fuel leakage by placing cardboard over high-
pressure fuel line and connection. Note if leak is being detected by
fuel being sprayed onto the cardboard. If leak exists, repair leak by
tightening high-pressure fuel line nut to 30 ft. lbs. (40 N.m) or
replacing high-pressure fuel line as necessary. If high-pressure fuel
line is replaced, bleed air from fuel system. See FUEL LINE BLEEDING
under FUEL SYSTEM in REMOVAL, OVERHAUL & INSTALLATION - TRUCKS -
DIESEL article. If no leaks are found, go to next step.
3) Remove suspect injector. See FUEL INJECTOR under FUEL
SYSTEM in REMOVAL, OVERHAUL & INSTALLATION - TRUCKS - DIESEL article.
Test injector with a diesel fuel injector tester. Follow tester
instructions. Replace fuel injector if fuel injector opening (pop)
pressure is not 4250-4750 psi (299-334 kg/cm
). Replace injector if
any leaks are noted at 291 psi (20 kg/cm) less than opening (pop)
pressure. Inspect injector for burrs, cracks, wear and plugging. Check
spray pattern. If any problems are noted, replace injector.
FUEL INJECTION PUMP TIMING
Improper fuel injection pump timing may result in low power,
excessive smoke and poor fuel economy. To check fuel injection pump
timing, see FUEL INJECTION PUMP TIMING in ADJUSTMENTS - TRUCKS -
DIESEL article.
INTAKE MANIFOLD AIR HEATER
NOTE: Intake manifold air heater is used to heat incoming air
before entering each cylinder. Warming of incoming air aids
in engine starting and improved driveability during cold
ambient temperatures. Engine Control Module (ECM) uses input
signals from various sensors for controlling intake manifold
air heater relays.
SUMMARY
If no faults were found while performing basic diagnostic
procedures, proceed to SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS
article. If no diagnostic trouble codes are found in self-diagnostics,
proceed to TROUBLE SHOOTING - NO CODES - DIESEL article for diagnosis
by symptom (i.e., ROUGH IDLE, NO START, etc.) or intermittent
diagnostic procedures.

gauge. Vacuum reading should be a minimum of 10 in. Hg. Turn engine
off. Vacuum should continue to hold at a minimum of 10 in. Hg.
2) If vacuum is not as specified, check for kinked or leaking
vacuum lines, defective check valve, defective vacuum reservoir or
poor engine performance. If no problems are found, check speed control
servo. See SPEED CONTROL SERVO.
Diesel Engines
1) Disconnect vacuum hose at speed control servo. Install
vacuum gauge to disconnected vacuum hose. Start engine and observe
gauge. Vacuum reading should be a minimum of 25 in. Hg. A vacuum
reservoir is not used on diesel vehicles.
2) If vacuum is not as specified, disconnect vacuum supply
hose from vacuum pump. Install vacuum gauge to vacuum pump. Start
engine and observe gauge. If vacuum reading is not 25 in. Hg or more,
replace vacuum pump. If vacuum reading 25 in. Hg or more, go to next
step.
3) Check all vacuum hoses to speed control servo, vacuum pump
and heater-A/C system for leaks. Check vacuum check valve for leaks
and proper operation. Vacuum check valve is located in vacuum hose
between speed control servo and vacuum pump. If no problems are found,
check speed control servo. See SPEED CONTROL SERVO.
CONNECTOR IDENTIFICATION
Fig. 1: Identifying Brake Switch Terminals
Courtesy of Chrysler Corp.

ELE C TR IC AL C O M PO NEN T L O CATO R

1999 D odge P ic ku p R 1500
1999 ELECTRICAL COMPONENT LOCATION
Chrysler Motors Electrical Component Location
Dodge; Ram Pickup
SAFETY PRECAUTION
WARNING: When working on vehicles equipped with Supplemental Restraint
System (SRS), never apply electrical voltage to the system.
This could cause the SRS (air bag) to be deployed.
BUZZERS, RELAYS & TIMERS









\









\









\









\









\









\









\







Component Component Location








\









\









\









\









\









\









\







A/C Compressor Clutch Relay On power distribution center.
Automatic Shut Down Relay On power distribution center.
Blower Motor Relay On power distribution center.
Central Timer Module Left side of dash, inboard of
steering column opening.
Combination Flasher Left side of dash, on
junction block.
Engine Starter Motor Relay On power distribution center.
Fog Lamp Relay On power distribution center.
Fuel Heater Relay (Diesel) On power distribution center.
Fuel Pump Relay On power distribution center.
Horn Relay On power distribution center.
Intake Air Heater Relay No. 1
(Diesel) On left inner fender, below
left battery.
Intake Air Heater Relay No. 2
(Diesel) On left inner fender, below
left battery.
Quad High Beam Relay On power distribution center.
Radio Choke Relay Behind center of dash, on
support.
Security Relay On power distribution center.
Trailer Tow Relay On power distribution center.
Transmission Control Relay On power distribution center.
Wiper Motor Relay On power distribution center.









\









\









\









\









\









\









\