1999 DODGE RAM tires

battery location weight steering wheel CD player trip computer battery

Page 210 of 1691

DODGE RAM 1999 Service Repair Manual AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *

AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85C for 2 hours is generally considered a
maximum limit).

Page 320 of 1691

DODGE RAM 1999 Service Repair Manual SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACH

SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACHING HARDWARE
WHEEL BEARINGS, RACES AND SEALS
WHEEL CYLINDERS
WIRING HARNESSES
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt:\
1) a Pledge of Assurance to their Customers and
2) the Motorist Assurance Program Standards of Service.
All participating service providers have agreed to subscribe
to this Pledge and to adhere to the promulgated Standards of Service
demonstrating to their customers that they are serious about customer
satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not

Page 345 of 1691

DODGE RAM 1999 Service Repair Manual Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............

Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding, affecting
performance ............ A .. Require repair or replacement.
Binding, not affecting
performance ............ 2 .. Suggest repair or replacement.
Broken .................. A .. Require repair or replacement.
Burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Burned, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
replacement.
Cracked, affecting
performance ............ A .. Require repair or replacement.
Cracked, not affecting
performance ............ 1 .. Suggest repair or replacement.
Float saturated ......... A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Malfunctioning .......... A ........... ( 2) Require repair or
replacement.
Melted, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Melted, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
replacement.
Missing ................. C ............ Require replacement.
Out of adjustment ....... B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Won't return ............ A .. Require repair or replacement.
Worn .................... 1 ............ Suggest replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Includes inoperative, intermittent operation, or failure to
perform all functions.
\
\
\
\
\
\
\

TIRES
Consult the vehicle owner's manual or vehicle placard for
correct size, speed ratings, and inflation pressure of the original
tires.
TIRE INSPECTION

Page 458 of 1691

DODGE RAM 1999 Service Repair Manual Apply multipurpose lubricant (NLGI grade 2 EP) to "U" joints
and slip joint fittings.
INSPECTION
Abnormal vibration and noise can come from many driveline
sources. Drive sha

Apply multipurpose lubricant (NLGI grade 2 EP) to "U" joints
and slip joint fittings.
INSPECTION
Abnormal vibration and noise can come from many driveline
sources. Drive shaft vibration/noise increases with vehicle speed
(MPH). A vibration that occurs within a specific speed is not caused
by drive shaft imbalance. Before overhauling driveline, check for
other causes/sources of possible vibration/noise.
TIRES & WHEELS
Check tire inflation and wheel balance. Check for foreign
objects in tread, damaged tread, mismatched tread patterns or
incorrect tire sizes. Check for bent wheels.
CENTER BEARING
Tighten drive shaft center bearing mounting bolts. If bearing
insulator is deteriorated or oil-soaked, or drive shaft can be moved
up/down in support, replace center bearing support assembly.
ENGINE & TRANSMISSION MOUNTS
Tighten mounting bolts. If rubber mounts are deteriorated or
broken, replace as needed.
DRIVE SHAFT(S)
Check drive shaft(s) for missing weights, broken welds, or
for dents affecting balance. Check for undercoating, mud, snow/ice on
drive shaft(s). Clean shafts thoroughly and test drive.
"U" JOINTS
Check for foreign material lodged in joints and flange/yokes.
Check for loose "U" joint-to-flange mounting bolts. Check for worn "U"
joint needle bearings. Check for Reddish-Brown rust-dust around "U"
joint caps. Replace "U" joints if necessary.
ADJUSTMENTS
CHECKING DRIVE SHAFT PHASING
One-Piece Drive Shafts
1) Ensure "U" joint flanges on either end of drive shaft are
in same plane. See Fig. 2. Drive shafts with slip joints between yokes
often have arrows to aid in alignment. If yokes are not in same plane,
disassemble slip joint from drive shaft splines. Install slip joint
back onto drive shaft splines, aligning "U" joint yokes. Test drive.
2) Single tube type drive shaft has slip joint on outside of
"U" joint yoke (at transmission end). If one-piece tube type drive
shaft yokes are out of alignment, the drive shaft is torque-twisted.
Drive shaft must be replaced.

Page 891 of 1691

$DODGE RAM 1999 Service Repair Manual Limited Slip \ \ \ \ \ \ \f Differential Model 248 (4WD) 7.3 Pts. (3$

Limited Slip
\
\
\
\
\
\
\f

Differential Model 248 (4WD) 7.3 Pts. (3.4L)

\
\
\
\
\
\
\f

Model 267 (2WD) 7 Pts. (3.3L)

\
\
\
\
\
\
\f

Model 267 (4WD) 7.8 Pts. (3.6L)

\
\
\
\
\
\
\f

Model 286 (2WD) 6.8 Pts. (3.2L)

\
\
\
\
\
\
\f

Model 286 (4WD) 10.1 Pts. (4.8L)

\
\
\
\
\
\
\
\f

Front Axle Model 216 6.8 Pts. (3.6L)

Lubricant

\
\
\
\
\
\
\f

Model 248 7.6 Pts. (3.6L)

\
\
\
\
\
\
\
\f

Transfer Case NV231 HD 2.5 Pts. (1.2L)

Fluid

\
\
\
\
\
\
\
\f

Power Take NV021 4.6 Pts. (2.1L)

Off Adapter

\
\
\
\
\
\
\
\f

Power Drained 2.7 Pts. (1.3L)

Steering

Fluid

\
\
\
\
\
\
\
\f

A/C Charge Capacity 32 Oz. (.9Kg)

Refrigerant

\
\
\
\
\
\
\
\f

Refrigerant A/C System Capacity 7.75 Oz. (230ML)

Oil

\
\
\
\
\
\
\
\f

Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L)

\
\
\
\
\
\
\f

All Others 35 Gal. (132L)

\

\
\
\

\
\
\
\f

(
1) - Capacities are recommended or calculated levels. Always use

dipstick (if available) to measure level.

\
\
\
\
\
\
\

WHEEL & TIRE SPECIFICATIONS
TIRE REPLACEMENT
The tires on your new vehicle provide a balance of many
characteristics. They should be inspected regularly for wear and
correct inflation pressure. Chrysler strongly recommends that you use
tires equivalent to the originals in quality and performance when
replacement is needed. Failure to use equivalent replacement tires may
adversely affect the safety, handling and ride of your vehicle. We
recommend that you contact your original equipment tire dealer on any
questions you may have on tire specifications or capability.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\

Lug Nut Ft. Lbs. (N.m)
BR1500 (5 Stud Wheel) ........................... 95 (130)
BR2500 (8 Stud Wheel) ........................... 135 (180)

Page 893 of 1691

DODGE RAM 1999 Service Repair Manual CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON

CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: Avoid breathing R-134a refrigerant and PAG lubricant vapors,
exposure may irritate eyes, nose and throat. To remove
R-134a from system use R-134a recycling equipment that meets
SAE J2210 specifications. If accidental system discharge
occurs, ventilate work area before resuming service.
WARNING: R-134a service equipment or vehicle A/C systems SHOULD NOT
be pressure tested or leak tested with compressed air. Some
mixtures of air/R134a have shown to be combustible at
elevated pressures. These mixtures are dangerous and may
cause fire and/or explosions. See AIR CONDITIONING SERVICE
article in GENERAL INFORMATION section.
AIR CONDITIONING MAINTENANCE
WARNING: NEVER add A/C refrigerant to correct a non-cooling problem
unless pressure gauges are connected to the system by a
certified technician. Lack of cooling may be caused by a
restriction, therefore adding refrigerant can cause a
dangerous pressure rise.
ANTI-LOCK BRAKE SYSTEM
CAUTION: The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly
installed or high output radio transmitting equipment. Since
this interference could cause the possible loss of the
antilock braking capability, such equipment should be
installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
AUTOMATIC TRANSAXLE FLUID SERVICE
WARNING: Make certain no fluid is spilled when the transaxle fluid
is inspected. Wipe up any spilled fluid completely.
AXLE FLUID
CAUTION: Axle lubricant should be changed whenever the axle has

Page 896 of 1691

DODGE RAM 1999 Service Repair Manual RADIATOR FAN
WARNING: Keep hands away from radiator fan.
STARTING FLUID USE (TURBO DIESEL)
WARNING: DO NOT USE starting fluids (ether) or flammable liquids to
aid the star

Page 999 of 1691

DODGE RAM 1999 Service Repair Manual SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)

1999 D odge P ic ku p R 1500
1997-99 MAINTENANCE
Chrysler Maintenance & Service Intervals
Diesel Engines
Norma

SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)

1999 D odge P ic ku p R 1500
1997-99 MAINTENANCE
Chrysler Maintenance & Service Intervals
Diesel Engines
Normal Service
DODGE; RAM PICKUP Cummins Turbo Diesel: 5.9L VIN [D]
* READ THIS FIRST *
Before preforming maintenance on vehicle, ensure that all
cautions and warnings have been observed to prevent vehicle damage or
personal injury. See CAUTIONS & WARNINGS in MAINTENANCE INFORMATION
article in this section.
Introduction
The frequency of scheduled inspection and maintenance
services in this article are based on normal vehicle usage ONLY. The
following Severe conditions are NOT taken into account:
* Frequent short driving less than 5 Miles (8 Km).
* Frequent driving in dusty conditions.
* Frequent trailer towing.
* Extensive idling.
* More than 50% of your driving is at sustained high speeds
during hot weather, above 90
F (32C).
If the vehicle is operated mainly under any of these
conditions, this Normal service schedule article is inadequate. DO NOT
USE. Instead, use the Severe service schedule: See
SCHEDULED SERVICES - NORMAL SERVICE (DIESEL) .
6,000 MILE (10,000 KM)/6 MONTH NORMAL SERVICE
6,000 MILE (10,000 KM)/6 MONTH NORMAL SERVICE\
\
\
\
\
\
\

INSPECT

\b\
\
\
\
\
\
\

Exhaust System

\
\
\
\
\
\
\

Brake Hoses

\
\
\
\
\
\
\

Engine Coolant Level, Hoses & Clamps

\
\
\
\
\
\
\

SERVICE

\b\
\
\
\
\
\
\

Rotate Tires

\
\
\
\
\
\
\

Lubricate Steering Linkage

\
\
\
\
\
\
\

REPLACE

\b\
\
\
\
\
\
\

Engine Oil

\
\
\
\
\
\
\

Engine Oil Filter

\
\
\
\
\
\
\

LUBRICATION SPECIFICATIONS

\
\b\
\
\
\b\
\
\

Material Condition Specification

\

\
\
\

\
\
\

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 33-40 ... 104 next >

child lock instrument cluster OBD port fuse diagram alternator belt heater