1999 DODGE RAM air bleeding

FUEL LINE BLEEDING
NOTE: Fuel line bleeding is necessary if fuel injection pump is
replaced, fuel filter/water separator is not filled with
diesel fuel before installing or vehicle ran out off fuel.
Bleed high-pressure fuel lines if connections are loosened or
replaced. If engine has not been operated for an extended
time, bleed fuel lines before next initial engine start-up.
WARNING: DO NOT bleed fuel lines on a hot engine, as high exhaust
temperatures may cause a fire. Carefully bleed fuel lines, as
fuel is under extremely high pressure and could penetrate
skin. Use safety goggles and protective clothing when
bleeding fuel lines.
1) Loosen banjo bolt holding low-pressure fuel supply line to
side of fuel injection pump. Wrap a towel around banjo fitting to
catch fuel. Crank engine quickly and release key before engine starts.
This will operate fuel transfer pump for about 25 seconds.
2) If fuel is not present at fuel supply line after 25
seconds, turn ignition off. Repeat engine crank procedure until fuel
is present at fuel supply line. Tighten banjo bolt at fuel supply line
to specification. See TORQUE SPECIFICATIONS.
CAUTION: Ensure parking brake is applied and transmission is in
Neutral before bleeding fuel injection pump or high-pressure
fuel lines. DO NOT operate starter for more than 30 seconds
when bleeding fuel injection pump or high-pressure fuel
lines. Allow 2-minute intervals between starter operations.
3) To bleed air from fuel injection pump, ensure parking
brake is applied and transmission is in Neutral, as engine may start
when operating starter to bleed air from fuel injection pump. Operate
starter for 30 seconds to bleed any trapped air in fuel injection
pump.
4) To bleed high-pressure fuel lines, ensure parking brake is
applied and transmission is in Neutral, as engine may start when
operating starter to bleed high-pressure fuel lines. Loosen high-
pressure fuel line nut at fuel injector.
5) Operate starter until steady fuel flow exists at high-
pressure fuel line. Tighten high-pressure fuel line nut to
specification. See TORQUE SPECIFICATIONS. Start engine. Repeat
procedure on each high-pressure fuel line until engine operates
smoothly.
FUEL FILTER/WATER SEPARATOR & WATER-IN-FUEL SENSOR
NOTE: Vehicle also contains an in-tank fuel filter located on
bottom of fuel tank module. For servicing procedure, see FUEL
TANK MODULE & IN-TANK FUEL FILTER under FUEL SYSTEM.
NOTE: When fuel filter/water separator is being replaced,
manufacturer recommends cleaning the pre-filter. See FUEL
HEATER under FUEL SYSTEM for servicing of pre-filter.
Removal
1) Ensure engine is off. Place drain pan below drain tube at
fuel filter/water separator. See Fig. 3. Rotate handle on drain valve
forward, toward front of vehicle to DRAIN position. Drain valve is
located near top of fuel filter/water separator. See Fig. 3. Once fuel
is drained from fuel filter/water separator, rotate handle on drain
valve back to CLOSE position.

Apply light coat of engine oil on NEW .060" (1.5 mm) thick Copper
sealing washer. Install NEW Copper sealing washer on spray tip of fuel
injector. Engine oil is used to aid holding sealing washer in place.
Install new "O" ring on fuel injector. Apply small amount of engine
oil to "O" ring.
2) Ensure fuel inlet hole on side of fuel injector is
positioned toward injector connector tube. Install injector into
cylinder head bore using care not to allow injector tip to touch sides
of bore. Press fuel injector into cylinder head with finger pressure
only. Install fuel injector hold down clamp into shouldered bolt while
aligning slot in top of injector into groove in bottom of clamp.
Tighten opposite clamp bolt to specification. See TORQUE
SPECIFICATIONS.
3) Apply small amount of clean engine oil to NEW "O" ring.
Install "O" ring to fuel injector connector tube. Using finger
pressure only, press injector connector tube into cylinder head.
Connect and tighten high pressure fuel lines to specification. See
TORQUE SPECIFICATIONS.
NOTE: Fuel line fitting torque is important. Mating surfaces will
not seal if fuel line fitting is under or over-torqued.
4) To install remaining components, reverse removal
procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS.
Bleed high-pressure fuel lines. See FUEL LINE BLEEDING under FUEL
SYSTEM.
FUEL INJECTION PUMP
CAUTION: High-pressure fuel lines must be clamped securely and routed
so they do not contact each other or any other components. DO
NOT weld or substitute high-pressure fuel lines. High
-pressure lines are same length and proper high-pressure fuel
line must be installed in specified area for proper engine
operation.
Removal
1) Disconnect negative battery cables. Clean fuel lines at
cylinder head and injection pump. Clean fuel injection pump and fuel
lines at side of pump. Disconnect 9-pin electrical connector at Fuel
Pump Control Module (FPCM). Place a rag around overflow valve to catch\
excess fuel. Remove overflow valve and disconnect fuel return line.
Remove banjo bolts and fuel supply line at side of injection pump and
top of fuel filter housing.
2) Remove all high pressure fuel lines, intake air tube,
accelerator pedal position sensor, air intake housing, engine oil
dipstick tube, wiring clips, electrical connectors at intake heaters,
and engine lifting bracket. Unscrew plastic access cap at front gear
cover. Remove injection pump gear-to-injection pump shaft nut and
washer.
3) Engine may be rotated by removing dust plug from
transmission adapter plate and installing Engine Barring Tool (Snap-On
SP371) in transmission adapter plate. See Fig. 9. Rotate engine until
keyway is at 12 o'clock position.

gear. When installing pump, ensure dowel on mounting flange must align
with hole in front of pump. Ensure fuel injection pump is flat against
gear housing. Install 4 fuel injection pump-to-gear housing nuts
finger tight. DO NOT tighten nuts at this time.
CAUTION: DO NOT tighten pump to gear cover using mounting nuts. Damage
to pump or gear cover may result. Pump must be positioned
flat to mounting flange before attempting to tighten mounting
nuts.
4) Install fuel injection pump shaft washer and nut to pump
shaft finger tight. Position lower pump bracket and install 3 bolts
finger tight. Tighten fuel injection pump drive gear nut to
preliminary torque of 22 ft. lbs. (30 N.m). Tighten 4 fuel injection
pump nuts and 3 lower pump bracket-to-pump bolts to specification.
Tighten 2 engine bracket-to-engine bolts to specification. See TORQUE
SPECIFICATIONS Final tighten injection pump shaft nut. Use barring
tool to prevent engine from rotating.
5) Install plastic access cap to front gear cover. Using new
gaskets, install fuel return line and overflow valve to side of
injection pump. Tighten overflow valve to specification. See TORQUE
SPECIFICATIONS Using new gaskets, install fuel supply line to side of
injection pump and top of fuel filter housing. Tighten banjo bolts to
specification. TORQUE SPECIFICATIONS.
6) To complete installation, reverse removal procedure. Bleed
air from fuel system. See FUEL LINE BLEEDING.
FUEL TANK ROLLOVER VALVE
Removal
1) Fuel tank rollover valve is pressed into rubber grommet on
top of fuel tank module. See Fig. 7. Manufacturer recommends removing
fuel tank for access to fuel tank rollover valve.
NOTE: It may be necessary to disconnect fuel lines and electrical
connector from fuel tank module so fuel tank may be lowered
for access to fuel tank rollover valve.
2) Raise and support vehicle. Disconnect negative battery
cables. Drain fuel tank. Remove fuel tank filler tube bolts from body.
Support fuel tank with transmission jack. Remove fuel tank straps and
heat shields (if equipped).
NOTE: Manufacturer recommends replacing rubber grommet on fuel tank
module when servicing fuel tank rollover valve.
3) Slightly lower fuel tank for access to fuel tank rollover
valve. Disconnect electrical connector and fuel lines from fuel tank
module if necessary to gain access to fuel tank rollover valve. Use
proper procedure when disconnecting fuel lines. See FUEL LINE
DISCONNECT FITTINGS under FUEL SYSTEM.
4) Disconnect hose from fuel tank rollover valve. Pry one
side of fuel tank rollover valve from rubber grommet. Remove fuel tank
rollover valve. Remove rubber grommet.
Installation
1) To install, reverse removal procedure using NEW rubber
grommet. If fuel lines were disconnected, install fuel lines on fuel
tank module using proper procedure. See FUEL LINE DISCONNECT FITTINGS
under FUEL SYSTEM.
2) Reinstall fuel tank. Tighten fuel tank strap nuts to
specification. See TORQUE SPECIFICATIONS. Reconnect negative battery
cables.

Relief Pressure Test
1) Close gauge shutoff valve completely 3 times. Record
highest pressure attained each time. All 3 readings must be greater
than specifications and within 50 psi (3.5 kg/cm

) of each other. See
POWER STEERING PUMP PRESSURE TEST SPECIFICATIONS table. If pressures
are not as specified, replace pump. See POWER STEERING PUMP (GASOLINE)\
or VACUUM/POWER STEERING PUMP (DIESEL) under REMOVAL & INSTALLATION.
CAUTION: DO NOT hold steering wheel against stops more than 4 seconds,
or pump damage may result.
2) Open test valve and turn steering wheel to left and right
stops. Record highest pressure attained at each stop. If output
pressures are not equal against each stop, gear is leaking internally
and must be replaced. See STEERING GEAR under REMOVAL & INSTALLATION.
Shut off engine, remove test gauge, and connect pressure hose.
LUBRICATION
CAPACITY
CAPACITY\
\
\
\
\
\
\

Models Pts. (L)\
Dakota (4WD) ............................................. 2.5 (1.2\
)
Ram Pickup & Ram Van/Wagon ............................... 2.7 (1.3)\
\
\
\
\
\
\
\

FLUID TYPE
CAUTION: DO NOT use Automatic Transmission Fluid (ATF).
Use Mopar Power Steering Fluid (4318055).
FLUID LEVEL CHECK
Check fluid level with engine cold and not running. Remove
fluid level dipstick on pump reservoir. Dipstick should indicate FULL
COLD with fluid temperature of 70-80
F (21-27C). If needed, add fluid
through dipstick opening, and recheck. DO NOT overfill.
HYDRAULIC SYSTEM BLEEDING
Fill power steering pump reservoir to specified level. Start
engine and slowly turn steering wheel to left and right, but DO NOT
contact steering stops in either direction. Stop engine. Inspect
reservoir fluid level and add fluid if necessary. Bleeding process may
have to be repeated several times to completely purge all air from
system.
ADJUSTMENTS
POWER STEERING PUMP BELT
Vehicles are equipped with dynamic tensioner. No adjustment
is required.
POWER STEERING PUMP PULLEY

Removal
1) Place wheels in straight-ahead position. Place drain pan
under steering gear assembly. Disconnect and cap pressure and return
hoses from steering gear. Disconnect steering column shaft coupling
from steering gear stub shaft.
2) Raise and support vehicle. Disconnect steering linkage
(center link) from pitman arm. See Fig. 9. Disconnect stabilizer bar
(if necessary). Place reference mark on pitman arm and sector shaft.
Remove nut and pitman arm from sector shaft. Remove steering gear-to-
frame bolts. Remove steering gear.
Installation
1) Install steering gear with bolts finger tight. Center
steering gear and align stub shaft with steering column. Install
steering column shaft coupling bolt and tighten to specification. See
TORQUE SPECIFICATIONS.
CAUTION: Stake pitman arm nut against pitman arm to ensure proper
retention.
2) Reposition steering gear to eliminate binding, and tighten
bolts to specification. Install pitman arm on sector shaft with
reference marks aligned. Install lock washer and nut. Tighten nut to
specification.
3) To install remaining components, reverse removal
procedure. Fill pump reservoir. Bleed air from hydraulic system. See
HYDRAULIC SYSTEM BLEEDING under LUBRICATION.
SECTOR SHAFT OIL SEAL
Removal
1) Raise and support vehicle. Place wheels in straight-ahead
position. Disconnect steering linkage (center link) from pitman arm.
Disconnect stabilizer bar (if necessary).
2) Place reference mark on pitman arm and sector shaft.
Remove nut and pitman arm from sector shaft. Place drain pan under
steering gear. Remove retaining ring and steel washer. See Fig. 1.
CAUTION: DO NOT hold steering wheel in left-turn position for more
than 2 seconds.
3) Start engine and momentarily hold steering wheel in
extreme left-turn position. When pressure develops, this should force
upper oil seal, steel washer and lower oil seal from steering gear
housing. Stop engine and remove seals.
Installation
1) Ensure seal bore of steering gear is free of burrs and
sector shaft is free of pitting or roughness. Lubricate replacement
seals and steel washers with power steering fluid.
2) Wrap sector shaft with plastic tape or .005" (.13 mm)
thick shim stock. Install upper oil seal (single lip seal) and steel
washer first. Oil seal must be installed only deep enough to allow for
remaining oil seal, steel washer and retaining ring.
CAUTION: DO NOT install upper oil seal against inner bore surface of
steering gear housing. Oil seals must be installed so each
oil seal is separately seated in shaft bore.
3) Install lower oil seal (double lip seal) and steel washer\
.
Oil seal must be installed only deep enough to allow for steel washer
and retaining ring. Remove tape or shim stock and install retaining
ring.

NOTE: A leaking fuel injector or high-pressure fuel line may cause
a rough idle, Black smoke, poor engine performance, poor fuel
economy and fuel knock. Following procedure is for
determining if fuel injector is defective.
WARNING: DO NOT allow diesel fuel to contact hot engine when checking
fuel injector, as high exhaust temperatures could cause a
fire. Use care when working around high-pressure fuel lines,
as fuel is under extreme pressure and could penetrate skin,
causing personal injury. Wear safety goggles and protective
clothing when checking fuel injectors.
Fuel Injector
1) Since a leaking high-pressure fuel line may cause the same
symptoms, check for leaking high-pressure fuel line before checking
fuel injector. To check for a leaking high-pressure fuel line, start
engine and allow engine to idle.
2) Inspect high-pressure fuel lines and connections for signs
of fuel leakage by placing cardboard over high-pressure fuel line and
connection. Note if leak is being detected by fuel being sprayed onto
cardboard. If leak exists, repair leak by tightening high-pressure
fuel line nut to 18 ft. lbs. (24 N.m) or replacing high-pressure fuel
line as necessary. If high-pressure fuel line is replaced, bleed air
from fuel system. See FUEL LINE BLEEDING under FUEL SYSTEM in REMOVAL,
OVERHAUL & INSTALLATION article.
3) To check for defective fuel injector, start and idle
engine. Loosen high-pressure fuel line nut at fuel injector and listen
for a decrease in engine speed. Tighten high-pressure fuel line nut to
18 ft. lbs. (24 N.m).
4) If fuel injector is operating properly, engine idle speed
should decrease when high-pressure fuel line nut is loosened. Repeat
procedure on each fuel injector.
5) If engine idle speed does not decrease, fuel injector is
defective and should be removed and tested with a diesel fuel injector
tester. Replace fuel injector if fuel injector opening (pop) pressure
is not about 4500 psi (316 kg/cm

).
EMISSION SYSTEMS & SUB-SYSTEMS
INTAKE MANIFOLD AIR HEATER SYSTEM
Intake Manifold Air Heater Preheat/Postheat Cycle
For testing information on intake manifold air heater system,
see DTC P0380: INTAKE AIR HEATER RELAY NO. 1 CONTROL CIRCUIT and DTC
P0382: INTAKE AIR HEATER RELAY NO. 2 CONTROL CIRCUIT tests in SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
MISCELLANEOUS CONTROLS
NOTE: Although some controlled devices listed here are not
technically engine performance components, they can affect
driveability if they malfunction.
TRANSMISSION
Park/Neutral Switch (A/T Models)
Park/neutral switch is mounted on transmission case, near
shift lever and contains a 3-pin connector. If problem exists in
park/neutral switch or wiring circuit, a Diagnostic Trouble Code (DTC)\
will be stored in Powertrain Control Module (PCM). See DTC P1899: P/N
SWITCH STUCK IN PARK OR IN GEAR test in SELF-DIAGNOSTICS - JEEP,