1999 DODGE RAM light

specifications.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - If a sensor is not adjustable, further inspection is
required to identify and correct cause.
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as metal
particles or water. Require repair or replacement.
( 4) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable; check
for accepted cleaning procedure.









\









\









\









\









\









\









\


STEEL BRAKE LINES
STEEL BRAKE LINE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Fitting incorrect (for
example, compression
fitting) ............... B ............ Require replacement.
Flare type incorrect .... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Line material incorrect
(copper, etc.) ......... B ............ Require replacement.
Restricted .............. A ............ Require replacement.
Routed incorrectly ...... B ..... Require routing correction.
Rust-pitted ............. 1 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.









\









\









\









\









\









\









\


STOPLIGHT SWITCHES
See BRAKE STOPLIGHT SWITCHES .
SWITCHES
NOTE: Copied from Electrical UIGs & added "float saturated" from
old fluid level sensor switches.
STEEL BRAKE LINE INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.

\









\









\









\









\









\









\







Application psi (kg/cm)
All Models ....................................... 10-15 (1.06-1.41)\









\









\









\









\









\









\









\







NOTE: When bleeding disc brakes, air may tend to cling to caliper
walls. Lightly tap caliper while bleeding to aid in removal
of air.
Manual Bleeding
1) Fill master cylinder. Install bleeder hose on first
bleeder valve to be serviced. See BLEEDING SEQUENCE table. Submerge
other end of hose in clean glass jar partially filled with clean brake
fluid.
NOTE: When bleeding brake system manually, ensure bleeder valve is
closed when brake pedal is released.
2) Open bleeder valve 3/4-1 turn. Depress brake pedal slowly
through full travel. Close bleeder valve. Release pedal. Repeat
procedure until fluid flow is free of air bubbles.
ADJUSTMENTS
PARKING BRAKE
1) Release parking brake, and loosen cable adjusting nut to
allow slack in cable. Adjust rear brakes. Tighten cable adjusting nut
until a slight drag is felt while rotating rear wheels.
2) Loosen cable adjusting nut until both rear wheels can be
rotated freely. Back off adjusting nut an additional 2 turns. Apply
and release parking brake several times, checking for free rotation at
rear wheels.
REAR BRAKE SHOES
1) Raise and support vehicle. Ensure parking brake lever is
fully released. Back off parking brake cable adjustment to ensure
cable has slack. Remove adjusting hole cover.
2) Using a brake adjuster, expand brake shoes until slight
drag is felt when wheel assembly is rotated. Using thin screwdriver,
hold automatic adjusting lever away from adjustment star wheel.
3) Back off adjustment star wheel until wheel assembly
rotates freely and brake shoe drag is eliminated. Repeat adjustment
for remaining wheels. Adjustment must be equal at all wheels. Replace
adjusting hole covers. Adjust parking brake. See PARKING BRAKE.
STOPLIGHT SWITCH
Stoplight switch is attached to brake pedal support. Push
stoplight switch through clip in mounting bracket until switch seats
in bracket. Pull brake pedal backward as far as pedal will travel.
Brake pedal will ratchet stoplight switch to correct position. Verify
full brake pedal return, and that stoplights glow when brake pedal is
applied.
TESTING
POWER BRAKE BOOSTER FUNCTIONAL TEST

1) Start engine, and check booster vacuum hose connections. A
hissing noise indicates a vacuum leak. Repair any vacuum leaks before
proceeding. Stop engine, and shift transmission into Neutral. Pump
brake pedal until all vacuum reserve in booster is depleted.
2) Hold brake pedal under light pressure. If pedal does not
hold firm and falls away, master cylinder may be faulty. Bleed system
using appropriate method, and repeat step 1). See BLEEDING PROCEDURES
under BLEEDING BRAKE SYSTEM.
3) If pedal still does not hold firm, master cylinder is
faulty. If pedal holds firm, start engine and observe pedal height. If
pedal height change is not apparent, power booster or vacuum check
valve is faulty. Install good check valve, and repeat steps 1) and 2).\
If pedal falls away slightly under light pressure and then holds firm,
go to next step .
4) Start engine. Release brake pedal. Increase engine speed
to 1500 RPM. Close throttle and immediately turn off ignition. Wait at
least 90 seconds, and try brake action again. Booster should provide 2
or more vacuum assisted pedal applications. If vacuum assist is not
provided, perform booster and check valve vacuum tests.
POWER BRAKE BOOSTER VACUUM TEST
Connect vacuum gauge to booster check valve using "T"
fitting. Start engine, and run at idle speed for one minute. Clamp
hose shut between vacuum source and check valve. Stop engine, and
observe vacuum gauge. If vacuum drops more than one in. Hg within 15
seconds, booster diaphragm or check valve is faulty.
POWER BRAKE BOOSTER CHECK VALVE TEST
Disconnect vacuum hose from check valve. Remove check valve
and valve seal from booster. Use a hand-operated vacuum pump for
testing. Apply 15-20 in. Hg at large end of check valve. Vacuum should
hold steady. If gauge on pump indicates vacuum loss, check valve is
faulty and should be replaced.
COMBINATION VALVE METERING VALVE TEST
Metering valve operation can be checked visually with aid of
an assistant. While an assistant applies and releases brake pedal,
observe metering valve stem. If valve is operating correctly, stem
will extend slightly when brakes are applied, and contract when brakes
are released. If valve is faulty, replace combination valve assembly.
COMBINATION VALVE PRESSURE DIFFERENTIAL SWITCH TEST
1) Using an assistant, apply brake pedal. Observe brake
warning light. Raise and support vehicle, and connect a bleed hose to
one rear wheel cylinder. Submerge other end of hose into container
partially filled with brake fluid. Have assistant press and hold brake
pedal down while observing brake warning light. Open bleeder screw. If
warning light glows, switch is operating properly.
2) If warning light fails to glow, check circuit fuse, bulb
and wiring. Repair as necessary. Repeat step 1). If warning light
fails to glow, check brakelight, parking brake switches and related
wiring. Repair as necessary. Repeat step 1). If warning light fails to
glow, pressure differential switch is faulty. Replace combination
valve assembly, and bleed brake system. Verify proper valve operation.
REMOVAL & INSTALLATION

pads at this time. On models with removable hub, install hub on rotor.
Install wheel and tire assembly. Tighten lug nuts so they are snug,
but DO NOT tighten to final torque specifications.
3) While rotating wheel, tighten adjuster nut sufficiently to
seat bearing. Loosen nut and retighten while still rotating wheel.
Back off adjuster nut to completely release bearing preload torque.
Ensure endplay of .001-.003" (.025-.076 mm). Install lock nut and NEW
cotter pin. If necessary, tighten lock nut slightly to align cotter
pin hole. Install grease cap. Tighten caliper bolts and lug nuts to
specification. See TORQUE SPECIFICATIONS table. To complete
installation, reverse remove procedure.
Removal (Ram Pickup With 8 Studs)
1) Raise and support vehicle. Remove wheel. Remove hub
extension, if equipped. Remove brake caliper. Support caliper aside.
2) On models with removable adapter hub, remove hub from
rotor. On models with one-piece hub and rotor assembly, remove cotter
pin from rotor hub nut. Remove nut. Disconnect ABS wheel speed sensor
wire (if equipped), and remove from frame and steering knuckle. Remove\
bolts securing hub to steering knuckle from inboard side of steering
knuckle. Remove rotor and hub assembly.
Installation
1) Apply anti-seize compound to drive shaft splines. Replace
grease seal in steering knuckle, if necessary. Insert 2 rearmost top
and bottom rotor hub bolts in steering knuckle so they extend through
back of knuckle. Install hub spacer, ensuring flat on space is
positioned to rear. Use chassis grease to hold spacer in position, if
necessary.
NOTE: If equipped with wheel speed sensor, brake shield must be
positioned on hub bearing, and sensor wire must be at top of
knuckle.
2) Align rotor hub with drive shaft and install hub assembly.
Align bolt holes in hub flange with bolts previously installed. Start
nuts on flange bolts sufficiently to hold assembly in place. Install
remaining bolts, and tighten all bolts to specification. See TORQUE
SPECIFICATIONS table.
3) Install washer and hub nut. Tighten nut securely. Install
NEW cotter pin. Install grease cap. Install caliper. Tighten caliper
bolts and lug nuts to specification. See TORQUE SPECIFICATIONS table.
To complete installation, reverse remove procedure.
REAR BRAKE SHOES
WARNING: Use water or brake cleaner to clean brake parts. DO NOT use
compressed air to remove dirt and dust.
Removal (Dakota & Ram Van)
1) Remove wheel and drum. Note how secondary spring overlaps
primary return spring. Using spring remover, remove brake shoe return
springs. Slide automatic adjuster cable off anchor. Disconnect cable
from adjusting lever.
2) Remove cable, cable guide and anchor plate. See Figs. 3,
4, and 5. Disconnect adjusting lever return spring from lever. Remove
lever and return spring from pivot pin. Remove shoe-to-shoe spring.
Spread shoes, and remove adjustment star wheel.
3) Remove shoe retainers, springs and pins. Remove parking
brake lever from secondary shoe. Remove shoes and parking brake strut
with spring.

being replaced, remove booster check valve and seal.
Installation
1) If new booster is being installed, install check valve and
seal. Position booster on dash, and install lock nuts on booster
mounting studs finger tight. Install booster push rod on brake pedal
pin, and secure rod with NEW retaining clip.
2) Tighten booster lock nuts to specification. Install master
cylinder on booster, and tighten mounting nuts to specification. See
TORQUE SPECIFICATIONS table. Connect vacuum hose to booster check
valve. Start vehicle and check booster operation.
COMBINATION VALVE
Removal & Installation
Raise and support vehicle. Mark brakelines for assembly
reference. Disconnect parking brake cable from clip on valve, if
necessary. Disconnect brake warning light connection at switch.
Disconnect all brake hydraulic lines at valve. Cap brakelines to
prevent dirt from entering system. Remove valve. To install, reverse
removal procedures. Bleed brake system. See BLEEDING PROCEDURES under
BLEEDING BRAKE SYSTEM.
AXLE BEARING & SEAL (FULL FLOATING AXLE)
Removal & Installation (Ram Pickup With 12" & 13" Drums)
1) Raise and support vehicle. Remove wheel. Remove axle shaft
nuts and washers. Strike center of axle flange to free cones. Remove
axle shaft and gasket.
2) Straighten and remove nut lock. Remove adjustment nut and
outer bearing. Remove drum assembly. Remove seal and inner bearing
from drum assembly.
3) Pack inner bearing, and install inner bearing and seal in
drum. Install drum assembly, outer bearing and adjustment nut. While
rotating drum, tighten adjustment nut to specification. See TORQUE
SPECIFICATIONS table.
4) Back off adjustment nut 1/8 turn to obtain .001-.010" (0.
025-0.254 mm) end play. Bend nut lock into spindle keyway. Install
gasket and axle shaft. Install wheel, and lower vehicle. See TORQUE
SPECIFICATIONS table.
OVERHAUL
NOTE: Use illustrations when overhauling components. See
Figs. 2-6.
DISC BRAKE SPECIFICATIONS
DISC BRAKE SPECIFICATIONS








\









\









\









\









\









\









\







Application In. (mm)\
Disc Diameter
Dakota ............................................... 11.30 (287)\
Ram Pickup
1/2 Ton ............................................. 11.57 (294)\
3/4 & 1 Ton ......................................... 12.50 (318)\
Ram Van
1/2 & 3/4 Ton ....................................... 11.75 (299)\
1 Ton ............................................... 12.82 (326)\
Lateral Runout

Removal (AX15 & NV1500)
1) Shift gear selector into 1st or 3rd gear. Raise and
support vehicle. Disconnect necessary exhaust system components.
Remove "Y" pipe and position remaining pipes for working clearance.
Support transmission adjustable jackstand. Disconnect rear cushion and
mounting bracket from transmission or transfer case.
2) Remove rear crossmember. If transmission will be
disassembled for repair, drain transmission fluid. Disconnect
transmission shift linkage, speedometer cable, transfer case vacuum
lines and clutch hydraulic lines. Lower transmission/transfer case
assembly no more than 3" (76 mm). Reaching around transmission case,
unseat and lift shift lever dust boot. Press shift lever retainer
downward, turn retainer counterclockwise, and lift lever and retainer
out of shift tower.
3) Mark front and rear drive shaft and "U" joint for
reassembly reference. Disconnect and remove both drive shafts. Remove
crankshaft position sensor (AX15). Disconnect transmission/transfer
case assembly vent hoses. Remove slave cylinder from clutch housing.
Remove wire harness from clips on transmission case and transfer case.
4) Support transmission/transfer case assembly with
transmission jack. Secure assembly to jack with safety chains.
Reposition adjustable jackstand under engine. Remove clutch housing
brace rod. Remove clutch housing nuts and bolts. Remove
transmission/transfer case assembly.
Installation
To install, reverse removal procedure. Apply high-temperature
grease to release fork, lever, pivot ball stud and pilot bushing
located in end of crankshaft. Fill transmission with appropriate
fluid, if necessary. Tighten all nuts and bolts to specification. See
TORQUE SPECIFICATIONS table.
Removal (NV 3500)
1) Disconnect negative battery cable. Shift transmission to
Neutral. Open console lid and remove bolts attaching console to floor
pan. Lift cup holder bin and remove bolt attaching console to floor
pan. Lift rear of console and pull console rearward to separate from
shift bezel. Remove console from vehicle. Remove screws attaching
shift boot to floor pan and slide boot upward on lever extension.
2) Remove shift lever extension. Raise and support vehicle.
On 4WD models, remove skid plate, if equipped. Mark drive shaft and
axle yoke for alignment reference. Remove drive shaft. Remove exhaust
"Y" pipe. On 4WD models, disconnect and lower remaining exhaust pipes
for clearance as necessary. Disconnect speed sensor harness connector
and back-up light harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
On 4WD models, disconnect transfer case shift linkage at transfer case
range lever and remove shift lever from transmission. Remove
bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and remove it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder and move aside for working
clearance. Remove starter. Remove transmission splash shield. Remove
transmission harness wires from clips on transmission shift cover.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine attaching bolts. Slide

transmission and jack rearward until input shaft clears clutch disc.
Lower transmission jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke. Apply sealer to threads of drain plug
before installing in case.
2) Align reference marks made on drive shaft(s) and "U"
joints during removal. After installing clutch assembly and housing,
tighten housing bolts nearest alignment dowels first. During final
transmission installation, install shims between clutch housing and
transmission at appropriate bolt location. Tighten all nuts and bolts
to specification. See TORQUE SPECIFICATIONS table.
TRANSMISSION (RAM PICKUP)
Removal (NV3500 & NV5600)
1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Remove shift tower and lever assembly. Raise and support
vehicle.
2) On 4WD models, remove skid plate, if equipped. Remove
crankshaft position sensor. Mark drive shaft and axle yoke for
alignment reference. Remove drive shaft. Remove exhaust "Y" pipe. On
4WD models, disconnect and lower remaining exhaust pipes for
clearance, as necessary. Disconnect speed sensor harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
On 4WD models, disconnect transfer case shift linkage at transfer case
range lever and remove shift lever from transmission. Remove
bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and remove it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder and move aside for working
clearance. Remove starter. Remove transmission splash shield. Remove
transmission harness wires from clips on transmission shift cover. On
some models, it may be necessary to remove front axle struts and oil
filter for access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and drive shaft slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first. Tighten all nuts and
bolts to specification. See TORQUE SPECIFICATIONS table.
Removal (NV4500 & NV4500HD)

1) Disconnect negative battery cable. Shift transmission to
Neutral. Remove shift boot bezel screws and slide boot upward on lever
extension. Scribe mark position of extension on shank of shift lever.
2) Raise and support vehicle. On 4WD models, remove skid
plate, if equipped. Mark drive shaft and axle yoke for alignment
reference. Remove drive shaft. Remove exhaust "Y" pipe. On 4WD models,
disconnect and lower remaining exhaust pipes for clearance as
necessary. Disconnect speed sensor harness connector and back-up light
harness connector.
3) Support engine using adjustable jackstand. If transmission
is to be disassembled for repair, drain lubricant from transmission.
See Fig. 9 . On 4WD models, disconnect transfer case shift linkage at
transfer case range lever and remove shift lever from transmission.
Remove bolts/nuts attaching transmission to rear mount.
4) Support transmission with a transmission jack. Secure
transmission with safety chains. Remove rear crossmember. On 4WD
models, support transfer case with transmission jack and secure
transfer case to jack with safety chains. Remove transfer case
attaching nuts and move transfer case rearward until input gear clears
transmission output shaft.
5) Lower transfer case assembly and move it from under
vehicle. On 4WD models, remove clutch slave cylinder splash shield, if
equipped. Remove clutch slave cylinder, and move aside. Remove
starter. Remove transmission splash shield. Remove transmission
harness wires from clips on transmission shift cover. On some models,
it may be necessary to remove front axle struts and oil filter for
access and removal clearance.
6) Lower transmission slightly. Remove shift tower and lever
assembly. Remove transmission-to-engine bolts. Slide transmission and
jack rearward until input shaft clears clutch disc. Lower transmission
jack and remove transmission from under vehicle.
Installation
1) To install, reverse removal procedure. Apply high-
temperature grease to pilot bushing located in end of crankshaft. Also
apply grease to release bearing bore, release fork, release fork ball
stud and propeller shift slip yoke.
2) Apply sealer to threads of drain plug before installing in
case. Align reference marks made on drive shaft(s) and axle yoke(s)
during removal. After installing clutch assembly and housing, tighten
housing bolts nearest alignment dowels first.
3) During final transmission installation, install shims
between clutch housing and transmission at appropriate bolt location.
See CLUTCH HOUSING BORE RUNOUT and CLUTCH HOUSING FACE RUNOUT under
CLUTCH HOUSING (RAM PICKUP) under TESTING. Press extension to scribe
mark made during removal. A 0.12-0.20" (3-5 mm) space should exist
between shift lever isolator, top edge of stub shaft and tool lower
jaw. Tighten all nuts and bolts to specification. See TORQUE
SPECIFICATIONS table.
Fig. 9: Identifying Transmission Drain Bolt (NV4500 & NV4500HD)
Courtesy of Chrysler Corp.
CLUTCH ASSEMBLY