1999 DODGE RAM key battery

CLUTCH ASSEMBLY
Removal (Except Grand Cherokee)
Remove compressor shaft bolt. Remove clutch plate and shims.
Tighten a 10-mm bolt into clutch hub bolt hole to remove clutch hub
and shims. Remove snap ring, and remove rotor and pulley assembly.
Remove snap ring, and disconnect clutch coil lead. Remove clutch coil.
Installation
1) Install clutch coil so pin in back of coil aligns with
hole in front compressor housing. Connect clutch coil lead. Install
snap ring with bevel side facing outward. Ensure snap ring is properly
seated in groove. Install rotor and pulley assembly. Install shims and
snap ring. Install clutch hub.
2) Install dial indicator at front of clutch hub to measure
clutch hub air gap. Using battery voltage, energize clutch coil.
Proper air gap is 0.014-0.026" (0.35-0.65 mm). Add or remove shims to
obtain correct air gap. Install compressor shaft bolt. On Concord and
Intrepid, tighten compressor shaft bolt to 11-15 ft. lbs. (15-20 N.m).\
On all other models, tighten compressor shaft bolt to 10 ft. lbs. (14
N.m).
NOTE: On Grand Cherokee, compressor clutch can be serviced in
vehicle without discharging A/C system.
Removal (Grand Cherokee)
Disconnect and isolate negative battery cable. Remove
serpentine drive belt. Remove compressor shaft bolt. Using a plastic
mallet, tap clutch plate to loosen from compressor shaft. Remove
clutch plate, shaft key and shims. See Fig. 5. Remove snap ring, and
remove pulley assembly. Remove snap ring, and disconnect clutch coil
lead. Remove clutch coil.
Installation
1) Install clutch coil so pin in back of coil aligns with
hole in front compressor housing. Connect clutch coil lead. Install
snap ring with bevel side facing outward. Ensure snap ring is properly
seated in groove. Align snap ring eyelets to the left or right of
clutch coil pin. Install rotor and pulley assembly. Install shims and
snap ring. Install clutch hub.
2) Hold clutch plate tight against shims and measure air gap
between clutch plate and pulley face. Air gap should be 0.014-0.026"
(0.35-0.65 mm). Add or remove shims as necessary. Install compressor
shaft bolt. Tighten compressor shaft bolt to 115 INCH lbs. (13 N.m).
To complete installation, reverse removal procedure.
3) After completing compressor clutch installation, start
engine. Set A/C-heater control to recirculated air mode and high
blower motor speed. Set engine speed to 1500-2000 RPM. Cycle
compressor on for 5 seconds and off for 5 seconds, about 20 times to
break-in clutch.
SHAFT SEAL
NOTE: Shaft seal replacement procedure is for 10PA17C compressor.
Shaft seal replacement procedure for 10PA17 compressor is not
available.
Removal
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove A/C compressor. Drain oil from
compressor, and measure amount drained. Remove clutch hub, shims,
rotor and pulley assembly, and clutch coil. See CLUTCH ASSEMBLY. See

Fig. 6: Compressor Components (Sanden MSC90-C Scroll)
Courtesy of chrysler corp.
SANDEN SD-7H15 7-CYLINDER
NOTE: On Cherokee, Dakota, Durango, Ram Pickup and Wrangler,
compressor clutch can be serviced in vehicle, without
discharging A/C system.
CLUTCH ASSEMBLY
Removal (Cherokee, Dakota, Durango, Ram Pickup & Wrangler)
1) Disconnect and isolate negative battery cable. Remove
serpentine drive belt. Disconnect clutch coil harness connector.
Without disconnecting refrigerant lines, remove A/C compressor from
mounting bracket. Support compressor in engine compartment.
2) Using spanner wrench, hold clutch plate and remove
compressor shaft nut. See Fig. 1. Using a steering wheel puller,
remove clutch plate, compressor shaft key and shims. Remove external
front housing snap ring.
3) Install jaws of Rotor Puller (C-6141-1) into pulley snap
ring groove. Install Shaft Protector (C-6141-2) over compressor shaft.\
Install puller flange plate on jaws. Install Puller Through-Bolts (C-
6461) through puller flange plate into jaws and hand tighten. Tighten
pulley center bolt clockwise and remove pulley from compressor.
4) Remove clutch coil wire harness retainer from compressor
housing. Remove clutch coil snap ring and clutch coil.

Installation (Cherokee & Wrangler)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub. Using Installer (C-
6871), press pulley and bearing assembly onto compressor housing hub.
Thread installer on compressor shaft and tighten nut until pulley
assembly is seated.
2) Install external front snap ring with beveled side facing
outward. Ensure snap ring is properly seated. Install compressor shaft
key and original shims. Using a plastic mallet and Driver (C-6463),
install clutch plate on compressor shaft. Tighten compressor shaft nut
to 10 ft. lbs. (14 N.m).
3) Using feeler gauge, measure air gap between clutch plate
and pulley assembly in several areas. Air gap should be 0.016-0.031"
(0.41-0.79 mm). If air gap is not within specification, adjust shim
thickness as necessary. If air gap is not consistent around clutch
plate, lightly pry up or tap down on clutch plate to make corrections.
To complete installation, reverse removal procedure.
Installation (Dakota, Durango & Ram Pickup)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub.
2) Install Handle (6464) and Driver (6143) into pulley
assembly bearing cavity. Ensure outer edge of driver rests firmly on
inner race of bearing. Using hammer, install pulley and bearing
assembly. While tapping on handle, guide pulley and bearing assembly
to prevent binding. Ensure pulley assembly bottoms against compressor
housing. Install external snap ring.
3) Install original shim(s) and compressor shaft key. Use a
hammer and Shaft Protector (6141-2) to install clutch plate on
compressor shaft. Ensure clutch plate bottoms out on clutch shims.
Replace compressor shaft nut and tighten compressor shaft nut to 10
ft. lbs. (14 N.m).
4) Measure air gap between clutch plate and pulley assembly
in several areas. Air gap should be 0.016-0.031" (0.41-0.79 mm). If
air gap is not within specification, adjust shim thickness as
necessary. If air gap is not consistent around clutch plate, lightly
pry up or tap down on clutch plate to make corrections. To complete
installation, reverse removal procedure. Ensure A/C system operates
properly.
5) After completing compressor clutch installation, start
engine. Set A/C-heater control to recirculated air mode and high
blower motor speed. Set engine speed to 1500-2000 RPM. Cycle
compressor on for 5 seconds and off for 5 seconds, about 20 times to
break-in clutch.
Removal (Ford "F" Series Super Duty Pickup)
1) Disconnect and isolate negative battery cable. Discharge
A/C system, using approved refrigerant recovery/recycling equipment.
Disconnect clutch coil harness connector and remove compressor. Drain
oil from compressor, and measure amount drained.
2) Using Spanner Wrench (T70P-4067-A), hold clutch plate and\
remove compressor shaft nut. See Fig. 1. If necessary, use a steering
wheel puller to remove clutch plate and shim(s).
3) Using a flat-blade screwdriver, remove pulley assembly
bearing dust cover. Remove compressor shaft key and internal bearing
snap ring. Remove external front housing snap ring.
4) Install jaws of rotor puller into pulley assembly internal
bearing snap ring groove. Install shaft protector over compressor
shaft. Install puller flange plate on jaws. Install 2 puller bolts
through puller flange plate into jaws and hand tighten. Tighten pulley
center bolt clockwise and remove pulley assembly from compressor.

Procedure Cylinders No.
Step 1 (1)
Intake Valve ............................................ 1, 2 & 4
Exhaust Valve ........................................... 1, 3 & 5
Step 2 ( 2)
Intake Valve ............................................ 3, 5 & 6
Exhaust Valve ........................................... 2, 4 & 6
( 1) - Perform STEP 1. See Fig. 2.
( 2) - Rotate engine clockwise (viewed from front of engine) one full
revolution from TDC on cylinder No. 1 (STEP 1) and align
reference marks. Perform STEP 2. See Fig. 2.









\









\









\









\









\









\









\








VALVE CLEARANCE SPECIFICATIONS ( 1)








\









\









\









\









\









\









\








Application In. (mm)\
Intake Valve ............................. ( 2) .006-.015 (.152-.381)
Exhaust Valve ............................ ( 3) .015-.030 (.381-.762)
( 1) - Adjust valve clearance with engine temperature less than
140
F (60C).
( 2) - Set to .010" (.254 mm) if adjustment is necessary.
( 3) - Set to .020" (.508 mm) if adjustment is necessary.









\









\









\









\









\









\









\








3) Rotate engine clockwise (viewed from front of engine) one\
full revolution from TDC on cylinder No. 1 and align reference marks.
Check valve clearance on proper valves. Perform STEP 2. See Fig. 2.
See VALVE CLEARANCE ADJUSTING SEQUENCE table. Ensure valve clearance
is within specification. See VALVE CLEARANCE SPECIFICATIONS table. If
valve clearance is within specification, go to next step. If valve
clearance is not within specification, loosen rocker lever adjusting
screw lock nut, and adjust valve clearance by rotating rocker lever
adjusting screw. Tighten rocker lever adjusting screw lock nut to
specification. See TORQUE SPECIFICATIONS. Go to next step.
4) Install valve cover, fuel pump access cover and battery
cables.
FUEL INJECTION PUMP TIMING
CHECKING FUEL INJECTION PUMP TIMING
NOTE: With Bosch VP 44 pump, no mechanical adjustments are
necessary. All timing and fuel adjustments are performed by
Engine Control Module (ECM). If a FTC indicating engine sync
error or static timing error has been set, perform following
adjustment. If FTC sets after installing a new pump, pump
keyway has probably been installed backward.
CAUTION: DO NOT allow nut and washer to fall inside front cover.
1) Remove fuel pump access cover, shaft nut and washer.
Ensure keyway aligning pump shaft to pump gear has not slipped. If
keyway has slipped, repair as necessary.
2) Remove timing gear cover. See REMOVAL, OVERHAUL &
INSTALLATION - TRUCKS - DIESEL article. Using a T-type puller, remove
injection pump gear from shaft. Ensure key has been installed in
keyway with arrow pointing to rear of pump. Pump timing is calibrated
to pump keyway. Ensure 3-digit number on key matches number on pump

PASSENGER AIR BAG DISARM (PAD) SWITCH
PAD switch is mounted on instrument panel. Switch allows
passenger-side airbag module to be disarmed when rear facing child
safety seat is being used. PAD switch is operated with ignition key.
SYSTEM OPERATION CHECK
Turn ignition on and observe AIR BAG warning light. AIR BAG
warning light should illuminate for 6-8 seconds and then go out,
indicating system is functioning properly. If AIR BAG warning light
either fails to illuminate or illuminates continuously, a system
malfunction exists. Perform self-diagnostics. See DIAGNOSIS & TESTING.
After completing necessary repairs, turn ignition switch to
ON position. Ensure no one is inside vehicle, then connect negative
battery cable. Using DRB, erase stored Diagnostic Trouble Codes (DTC).\
See DIAGNOSIS & TESTING .
SERVICE PRECAUTIONS
These precautions should be observed when working with air
bag systems:
* Disable air bag system before servicing any air bag system
or steering column component. Failure to do this could
result in accidental air bag deployment and possible
personal injury. See DISABLING & ACTIVATING AIR BAG SYSTEM .
* Back-up power supply maintains deployment voltage for about
2 minutes after battery is disconnected. When disabling air
bag system, always wait at least 2 minutes after
disconnecting battery cables to resume procedure.
* After repairs, ensure AIR BAG warning light works
properly and no system faults are indicated. See
SYSTEM OPERATION CHECK .
* Always wear safety glasses when servicing or handling an
air bag.
* All SRS component fasteners are specially coated and are
designed with a specific function. Never replace SRS
component fasteners with other than original equipment parts.
* Air bag module must be stored in its original special
container until used for service. It must be stored in a
clean, dry, place, away from sources of extreme heat, sparks
and high electrical energy.
* When placing a live air bag on a bench or other surface,
always face air bag and trim cover up, away from surface.
This will reduce motion of module if accidentally deployed.
* After deployment, air bag surface may contain deposits of
sodium hydroxide, which irritates skin. Always wear safety
glasses, rubber gloves, and long-sleeved shirt during
clean-up and wash hands using mild soap and water. Follow
correct disposal procedures. See DISPOSAL PROCEDURES.
* Because of critical system operating requirements, DO NOT
attempt to service any air bag components. Corrections are
only made by replacing defective part.
* Electrical sources should never be allowed near inflator on
back of air bag module.
* When carrying a live air bag module, trim cover should be
pointed away from your body to minimize injury in case of
deployment.
* When testing voltage or continuity at Air Bag Control Module

CAUTION: When removing a deployed air bag, wear eye protection, rubber
gloves and a long-sleeve shirt. Powder residue from air bag
deployment may irritate skin and eyes.
CAUTION: Before removing steering wheel, position front wheels in
straight-ahead position and lock steering column by removing
ignition key. Failure to do so could damage clockspring or
cause clockspring to be off-centered. DO NOT hammer on
steering wheel during removal, or collapsible column could be
damaged.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Air bag module
is mounted on face of steering wheel. Ensure wheels are pointed
straight-ahead and steering wheel is locked.
2) Remove air bag module-to-steering wheel screws from back
side of steering wheel. Lift air bag module and disconnect electrical
connectors from rear of module.
Installation
Connect air bag, cruise control and horn harness connectors
to rear of air bag module. Secure module to steering wheel. Tighten
air bag module-to-steering wheel screws to specification. See
TORQUE SPECIFICATIONS . DO NOT connect negative battery cable at this
time. Go to SYSTEM OPERATION CHECK .
PASSENGER-SIDE AIR BAG MODULE
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
3) Remove 3 screws securing instrument panel glove box
opening upper trim strip to instrument panel glove box opening upper
reinforcement, then remove trim strip. Remove 4 screws that secure 2
plastic support brackets of passenger-side air bag door panel outlet
housing to glove box opening upper reinforcement.
4) Reach through and above glove box opening to access and
disconnect air bag module harness connector. Remove 2 screws securing
passenger-side air bag module front bracket to instrument panel
structural support. Remove 3 screws securing passenger-side air bag
module rear bracket to glove box opening upper reinforcement.
5) Using trim stick, gently pry passenger-side air bag door
(starting at lower left edge) away from instrument panel top cover.
Remove air bag module, air bag door and panel outlet housing and
barrel assembly from instrument panel as a unit.
Installation
To install, reverse removal procedure. Ensure air bag door is
securely attached to instrument panel. Ensure air bag harness
connector latches fully engaged. DO NOT connect negative battery cable
at this time. Go to SYSTEM OPERATION CHECK .
CLOCKSPRING
CAUTION: Failure to position wheels in the straight-ahead position
with steering wheel locked when removing steering wheel could

Requested WARM boot or User-Requested COLD boot. If DRB should display
any other error message, record entire display and contact
manufacturer.
2) If DRB does not power-up, check for loose cable
connections or a bad cable. Check vehicle battery voltage (data link
connector terminal No. 16). A minimum of 11 volts is required to
adequately power DRB.
3) If all connections are proper between DRB and vehicle or
other devices, and vehicle battery is fully charged, an inoperative
DRB may be result of faulty cable or vehicle wiring.
ENTERING ON-BOARD DIAGNOSTICS
1) Before entering on-board diagnostics, refer to
PRETEST INSPECTION & DIAGNOSTIC PROCEDURE . Connect DRB to data link
connector. Data link connector (DLC) is located under left side of
instrument panel, left of steering column.
NOTE: Read active DTCs with PAD switch in both ON and OFF
positions. Always turn ignition off before changing PAD
switch positions,
2) Turn ignition switch to ON position. Exit vehicle with
DRB. Using DRB, read and record active Diagnostic Trouble Code (DTC)
data. Read and record stored DTC data. If any DTCs (fault messages)
exist, perform appropriate test.
3) If PAD switch OFF indicator fails to illuminate when in
the OFF position, go to PAD SWITCH INDICATOR PROBLEMS . If PAD switch
OFF indicator illuminates when switch is in ON position or key
cylinder does not operate, replace PAD switch.
4) Air Bag Control Module (ACM) may report any of the
following DTCs or fault messages. If the following active or stored
codes are reported by DRB, replace ACM. See
AIR BAG CONTROL MODULE (ACM) under REMOVAL & INSTALLATION.
* ACM OUTPUT DRIVER CIRCUIT OPEN
* ACM ACCELEROMETER
* ACM INTERNAL DIAGNOSTIC CODE #1
* WARNING LAMP DRIVER ERROR
* FIRING CAPACITOR LOW
* LOGIC CAPACITOR LOW
* SAFING SENSOR SHORTED
If the following active codes are reported by DRB, go to the
appropriate procedure under DIAGNOSTIC TESTS.
* CLUSTER MESSAGE MISMATCH
* DRIVER SQUIB CIRCUIT OPEN
* DRIVER SQUIB CIRCUIT SHORTED
* DRIVER SQUIB CIRCUIT SHORTED TO BATTERY
* DRIVER SQUIB CIRCUIT SHORTED TO GROUND
* LOSS OF IGNITION RUN ONLY
* LOSS OF IGNITION RUN/START
* NO CLUSTER CCD MESSAGE
* NO CCD COMMUNICATION
* MISSING OR INVALID VIN
* PASSENGER SQUIB CIRCUIT OPEN
* PASSENGER SQUIB CIRCUIT SHORTED
* PASSENGER SQUIB CIRCUIT SHORTED TO BATTERY
* PASSENGER SQUIB CIRCUIT SHORTED TO GROUND
* SCTM FAILURE
* SCTM MESSAGE MISMATCH
* VIN MESSAGE MISMATCH


AN TI- T H EFT S YSTE M

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Anti-Theft Systems
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION
The Vehicle Theft Security System (VTSS) provides an engine
no-run feature, flashes headlights and sounds horn if any door or hood
is opened without using key or remote keyless entry transmitter, or if
battery cables are disconnected then reconnected when system is
activated.
Anti-theft system is controlled by Central Timer Module
(CTM). CTM is located under driver's side of dash panel, right of
steering column. If CTM is faulty, CTM cannot be repaired and must be
replaced.
VTSS is also equipped with a power-up mode. If battery is
disconnected or looses power while VTSS is armed, VTSS system remains
armed when power is restored. A temper alert signal is sounded on
vehicle entry if VTSS was triggered while away from vehicle. Horn will
sound 3 times alerting owner VTSS was triggered.
OPERATION
ARMING PROCEDURE (PASSIVE)
Remove key from ignition. Ensure headlights are off. Lock
doors while open, using power lock switch. Power lock switch will not
operate with key in ignition or headlights on while door is open.
Vehicle Theft Security System (VTSS) will not arm using key in lock
cylinder or mechanical lock button. While system is arming, SECURITY
light will flash rapidly for 15 seconds. Opening any door or turning
the ignition key while light is flashing will abort arming process.
Once arming process is complete, SECURITY light will go out.
ARMING PROCEDURE (ACTIVE)
Pressing Remote Keyless Entry (RKE) transmitter LOCK button
will actively arm Vehicle Theft Security System (VTSS). All doors must\
be closed and ignition switch in OFF position. While system is arming,
SECURITY light will flash rapidly for 15 seconds. Opening any door or
turning the ignition key while light is flashing will abort arming
process. Once arming process is complete, SECURITY light will go out.
DISARMING
Vehicle Theft Security System (VTSS) can be disarmed 2 ways:
unlock vehicle using key in any door and pressing remote keyless entry
transmitter UNLOCK button. If alarm has been set off, either method
can be used to disarm and shut-off horn.
CENTRAL TIMER MODULE (CTM)
Central Timer Module (CTM) is Vehicle Theft Security System
(VTSS) processor. CTM uses the data bus network to allow sharing and
reporting of sensor information. If a door ajar sensor is opened while
VTSS is set, a signal is sent to flash headlights and sound horn. PCM
is also notified through bus network to enable engine no-run feature.