1999 DODGE RAM key battery

CTM has remote keyless entry receiver and control logic incorporated.
COMPONENT TESTS
RELAYS
NOTE: Headlight relay may also be referred to as the security
relay. On Ram Pickup, the headlight relay is located in Power
Distribution Center (PDC) in engine compartment. On Ram Van
and Ram Wagon, the headlight relay is taped to headlight
switch harness. On Ram Pickup, the horn relay is located in
Power Distribution Center (PDC) in engine compartment. On Ram\
Van and Ram Wagon, the horn relay is located in junction
block under left side of instrument panel. For circuit
testing, see WIRING DIAGRAMS.
Headlight Relay & Horn Relay
Remove relay to be tested. Measure resistance between
appropriate relay terminals with relay de-energized and energized. See
RELAY TEST SPECIFICATIONS table. See Fig. 1. If continuity or
resistance is not as specified, replace relay.
RELAY TEST SPECIFICATIONS









\









\









\









\









\









\









\







Terminals Condition
De-Energized
87A & 30 .............................................. Continuity
87 & 30 ............................................ No Continuity
85 & 86 .................................... 70-80 Ohms Resistance
Energized ( 1)
87 & 30 ............................................... Continuity
87A & 30 ........................................... No Continuity
( 1) - Apply position battery voltage to terminal No. 85 and ground
terminal No. 86.









\









\









\









\









\









\









\







Fig. 1: Identifying Relay Connector Terminals
Courtesy of Chrysler Corp.
SYSTEM TESTS

Box (DRB) scan tool with appropriate cartridge for system
diagnosis. Other after-market scan tools may be used for
system diagnosis. The following procedure is for DRB scan
tool usage. Use scan tool manufacturer's instruction for
operating scan tool.
NOTE: Ensure battery is fully charged before proceeding with test.
1) Ensure ignition is off. Connect DRB to Data Link Connector
(DLC) located under driver's side of instrument panel. Using scan
tool, display all Diagnostic Trouble Codes (DTCs). Identify DTCs once
retrieved. See DIAGNOSTIC TROUBLE CODES (DTC) & DRB MESSAGES table.
2) If scan tool will not power up, check for loose cable
connections or faulty cable. If cable connections and cable are okay,
check voltage at DLC terminal No. 16. Voltage should be at least 11
volts. If voltage is not as specified, check wiring circuit and
necessary fuses. See WIRING DIAGRAMS.
3) If scan tool displays an error message, RAM TEST FAILURE,
CARTRIDGE ERROR, KEY PAD TEST FAILURE, or LOW OR HIGH BATTERY, this
indicates a scan tool failure.
4) If DTCs are displayed, perform appropriate test(s). See
DIAGNOSTIC TROUBLE CODES (DTC) & DRB MESSAGES table. If no DTCs are
displayed, see TROUBLE SHOOTING in appropriate AUTOMATIC TRANSMISSION
OVERHAUL article.
DIAGNOSTIC TROUBLE CODES (DTC) & DRB MESSAGES









\









\









\









\









\









\









\







DTC DRB-III Scan Tool Message
P0711 .................. TRANS TEMP SENSOR, NO TEMP RISE AFTER START
P0712 ............................. TRANS TEMP SENSOR VOLTAGE TO LOW
P0713 ............................ TRANS TEMP SENSOR VOLTAGE TO HIGH
P0720 ..................... LOW OUTPUT SPEED SENSOR RPM ABOVE 15 MPH
P0740 .................... TORQ CONVERTER CLU, NO RPM DROP AT LOCKUP
P0743 ........ TORQUE CONVERTER CLUTCH SOLENOID/TRANS RELAY CIRCUITS
P0748 ........... GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIRCUITS
P0751 ....................... OD SWITCH PRESSED (LO) MORE THAN 5 MIN\
P0753 ................ TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS
P0783 ....................... 3-4 SHIFT SOL, NO RPM DROP @ 3-4 SHIFT
P1740 (1) .......................... TCC OR O/D SOLENOID PERFORMANCE
P1756 .................... GOV PRESS NOT EQUAL TO TARGET @ 15-20 PSI
P1757 ...................... GOV PRES ABOVE 3 PSI IN GEAR WITH 0 MPH
P1762 .................... GOV PRESS SEN OFFSET VOLTS TO LOW OR HIGH
P1763 ....................... GOVERNOR PRESSURE SENSOR VOLTS TO HIGH
P1763B ...................... GOVERNOR PRESSURE SENSOR VOLTS TO HIGH
P1764 ........................ GOVERNOR PRESSURE SENSOR VOLTS TO LOW
P1765 ..................... TRANS 12 VOLT SUPPLY RELAY CNTRL CIRCUIT
P1899 .......................... P/N SWITCH STUCK IN PARK OR ON GEAR
( 1) - BR body only.









\









\









\









\









\









\









\







CLEARING DIAGNOSTIC TROUBLE CODES
After repairs have been performed, clear DTCs from PCM memory
using scan tool, following scan tool manufacturer's instructions.
NOTE: If malfunction is no longer present after DTC is stored in
PCM memory, the PCM will erase DTC after ignition has been
cycled at least 50 times. DTC may be cleared by using scan
tool. Follow scan tool manufacturer's instructions. DTCs may
also be cleared by disconnecting negative battery cable for a
period of time, but other vehicle control modules may also be

5) If PCM has not been replaced, and TEST VER-2A is being
performed after an A/C relay control circuit DTC test, ensure A/C is
on and go to next step.
6) Road test vehicle for at least 5 minutes. Road test
vehicle at a speed of at least 40 MPH at some point during road test.
Stop vehicle. Turn engine off for at least 10 seconds. Start engine
and continue road test. Ensure transmission shifts through all gears.
After road test, turn engine off and go to next step.
7) Using scan tool, read DTCs. If any DTC returns, perform
appropriate test(s). If no DTCs return, test is complete. Go to next
step.
8) Turn ignition on, with engine off. Using scan tool, erase
DTCs. Turn ignition off. Disconnect scan tool. Test is complete.
TEST VER-2A (DIESEL)
NOTE: If Accelerator Pedal Position Sensor (APPS), battery, Engine
Control Module (ECM) or Powertrain Control Module (PCM) has\
been disconnected or replaced, APPS must be reprogrammed and
correct vehicle mileage and Vehicle Identification Number
(VIN) must be programmed into PCM to prevent Diagnostic
Trouble Codes (DTCs) from being set in Anti-Lock Brake System\
(ABS) module and Supplemental Restraint System (SRS) module\
.
To program PCM and clear DTCs from ABS and SRS modules,
proceed to appropriate procedure listed below. On models
equipped with a Smart Key Immobilizer Module (SKIM), if
replacing Powertrain Control Module (PCM), secret key data
must also be updated to enable engine starting. To update
secret key data, proceed to appropriate procedure listed
below.
CAUTION: DO NOT attempt to adjust screws or disassemble APPS. Settings
are preset at factory and are not intended to by changed.
Procedure For Programming APPS
Reassemble all components. Turn ignition switch to ON or RUN
position without starting engine. Slowly press accelerator pedal to
floor once and slowly release. This procedure programs APPS
calibration in ECM. Go to step 1)).
Procedure For Programming PCM & Clearing DTCs From ABS & SRS
Modules
Connect scan tool to Data Link Connector (DLC). Using scan
tool, enter correct VIN and mileage into PCM. Using scan tool
manufacturer's instructions, clear DTCs from ABS and SRS modules. Go
to step 1)).
Procedure For Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC). Go to ENGINE
and then MISC menus on scan tool. Place SKIM in SECURED ACCESS MODE by
using appropriate Personal Identification Number (PIN) for this
vehicle. PIN may be obtained from owner, vehicle's invoice, or from
manufacturer. Select UPDATE THE SECRET KEY DATA. Data will be
transferred from Smart Key Immobilizer Module (SKIM) to PCM. Go to
step 1)).
1) If PCM has not been replaced, and TEST VER-2A (DIESEL) is\
being performed after a No Trouble Code (NTC) test, inspect vehicle to\
ensure all engine components are connected. Reassemble and reconnect
components as necessary. Check if initial symptom still exists. If
initial symptom exists, check for Technical Service Bulletins (TSBs)
that apply to vehicle and see TEST NTC-1A: NO TROUBLE CODE TEST MENU
in ENGINE PERFORMANCE, or appropriate TROUBLE SHOOTING - NO CODES

4) Using scan tool, monitor pretest enabling conditions until
all conditions have been met. Once all enabling conditions are met,
observe appropriate monitor for DTC on scan tool. If repaired DTC has
reset or is seen on monitor while on road test, repair is not
complete. Check for related Technical Service Bulletins (TSBs) and
return to appropriate test. If no DTCs return, test is complete. Go to
step 6).
5) If another DTC exists, return to appropriate test(s). If
no DTCs return, test is complete. Go to next step.
6) Turn ignition on, with engine off. Using scan tool, erase
DTCs. Turn ignition off. Disconnect scan tool. Test is complete.
TEST VER-5A (DIESEL)
NOTE: If Accelerator Pedal Position Sensor (APPS), battery, Engine
Control Module (ECM) or Powertrain Control Module (PCM) has\
been disconnected or replaced, APPS must be reprogrammed and
correct vehicle mileage and Vehicle Identification Number
(VIN) must be programmed into PCM to prevent Diagnostic
Trouble Codes (DTCs) from being set in Anti-Lock Brake System\
(ABS) module and Supplemental Restraint System (SRS) module\
.
To program PCM and clear DTCs from ABS and SRS modules,
proceed to appropriate procedure listed below. On models
equipped with a Smart Key Immobilizer Module (SKIM), if
replacing Powertrain Control Module (PCM), secret key data
must also be updated to enable engine starting. To update
secret key data, proceed to appropriate procedure listed
below.
CAUTION: DO NOT attempt to adjust screws or disassemble APPS. Settings
are preset at factory and are not intended to by changed.
Procedure For Programming APPS
Reassemble all components. Turn ignition switch to ON or RUN
position without starting engine. Slowly press accelerator pedal to
floor once and slowly release. This procedure programs APPS
calibration in ECM. Go to step 1)).
Procedure For Programming PCM & Clearing DTCs From ABS & SRS
Modules
Connect scan tool to Data Link Connector (DLC). Using scan
tool, enter correct VIN and mileage into PCM. Using scan tool
manufacturer's instructions, clear DTCs from ABS and SRS modules. Go
to step 1)).
Procedure For Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC). Go to ENGINE
and then MISC menus on scan tool. Place SKIM in SECURED ACCESS MODE by
using appropriate Personal Identification Number (PIN) for this
vehicle. PIN may be obtained from owner, vehicle's invoice, or from
manufacturer. Select UPDATE THE SECRET KEY DATA. Data will be
transferred from Smart Key Immobilizer Module (SKIM) to PCM. Go to
step 1)).
1) If PCM has not been replaced, inspect vehicle to ensure
all engine components are connected. Reassemble and reconnect
components as necessary. If any DTCs have not been diagnosed, return
to appropriate test(s). If all DTCs have been diagnosed and repaired,
go to next step.
2) Ensure fuel tank is at least 1/4 full. Ensure A/C is off.
Proper way to ensure DTC is repaired is to connect scan tool to Data
Link Connector (DLC) and allow Powertrain Control Module (PCM) to ru\
n
a DTC SPECIFIC GOOD TRIP COUNTER for 2 minutes. If DTC SPECIFIC GOOD

BO DY C O NTR O L C O M PU TE R

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Body Control Computer Tests
Ram Pickup
NOTE: See BODY CONTROL COMPUTER - INTRODUCTION article before
proceeding with following test. Body control computer in RWD
trucks is the Central Timer Module (CTM).
SYMPTOM IDENTIFICATION
IDENTIFYING VEHICLE EQUIPMENT & SYSTEM PROBLEMS
NOTE: For connector terminal identification wiring diagrams, see
BODY CONTROL COMPUTER - INTRODUCTION article.
NOTE: Perform a visual inspection before proceeding with this test.
Ensure battery is fully charged.
1) Connect scan tool to Data Link Connector (DLC). DLC is a
16-pin connector located under left side of dash, to left of steering
wheel. Turn ignition switch to ON position. If scan tool display is
not blank, go to next step. If scan tool display is blank, see
appropriate VEHICLE COMMUNICATIONS article.
2) Using scan tool, select SYSTEM MONITORS, then CCD BUS
TEST. Scan tool will perform a CCD bus test. If scan tool displays BUS
OPERATIONAL, go to next step. If scan tool displays any message except
BUS OPERATIONAL, see appropriate VEHICLE COMMUNICATIONS article.
3) Using scan tool, select READ DTCs. If any Diagnostic
Trouble Codes (fault messages) are present, go to appropriate fault
message. If no fault messages are present, identify customer
complaint. See following list for possible fault messages and customer
complaint symptoms. Problems listed are diagnosed using a scan tool.
These problems may occur separately or in various combinations. When
diagnosing a system with many apparent problems, a sequence of tests
may be required. After repairs, ensure problem(s) or failure(s) have\
been corrected.
CHIME SYSTEM
* CHIME INOPERATIVE - ENGINE TEMPERATURE CRITICAL
* CHIME INOPERATIVE - KEY IN IGNITION & LF DOOR OPEN
* CHIME INOPERATIVE AT ALL TIMES
* CHIME INOPERATIVE WITH EXTERIOR LIGHTS ON
* CHIME INOPERATIVE WITH LOW OIL PRESSURE
* CHIME INOPERATIVE WITH DRIVER DOOR OPEN
DOOR AJAR SYSTEM
* OPEN LEFT DOOR AJAR CIRCUIT
* OPEN RIGHT DOOR AJAR CIRCUIT
* SHORTED LEFT DOOR AJAR CIRCUIT
* SHORTED RIGHT DOOR AJAR CIRCUIT
INSTRUMENT CLUSTER
* ALL GAUGES INOPERATIVE
* ANY CCD CLUSTER WARNING LIGHT INOPERATIVE
* ANY HARD WIRED CLUSTER WARNING LIGHT INOPERATIVE

14) Connect test light to ground and probe Orange/Black wire
of door lock actuator connector. If test light illuminates while door
unlock switch is pressed, repair open Orange/Black wire between door
lock actuator and Central Timer Module (CTM). CTM is located behind
right kick panel. If test light does not illuminate while door unlock
switch is pressed, go to next step.
15) Access CTM 18-pin connector C2. Remove connector cover.
Do not disconnect connector. Using an external voltmeter, measure
voltage between ground and CTM 18-pin connector C2 terminal No. 9
(Pink/Black wire). If voltage is more than 9.5 volts while door unlock\
switch is pressed, repair open Pink/Black wire. If voltage is 9.5
volts or less while door unlock switch is pressed, replace CTM.
16) Disconnect inoperative lock switch connector. Using an
external voltmeter, measure voltage between ground and Red wire of
door lock switch connector. If voltage is more than 9.5 volts, repair
open Red wire between door lock switch connector and voltage source.
If voltage is 9.5 volts or less, go to next step.
17) Reconnect door lock switch connector. Measure voltage
between ground and backprobe Pink/Violet wire of door lock switch
connector. If voltage is more than 9.5 volts, go to next step. If
voltage is 9.5 volts or less, replace door lock switch.
18) Access CTM 18-pin connector "B". Remove connector cover.
Do not disconnect connector. Using an external voltmeter, measure
voltage between ground and CTM 18-pin connector "B" terminal No. 13
(Pink/Dark Green wire). If voltage is more than 9.5 volts, replace
CTM. If voltage is 9.5 volts or less, repair open Pink/Dark Green wire
between CTM and door lock switch.
REMOTE KEYLESS ENTRY PROBLEM
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select SYSTEM MONITORS, then CCD BUS TEST.
If scan tool displays BUS OPERATIONAL, go to next step. If scan tool
does not display BUS OPERATIONAL, go to appropriate VEHICLE
COMMUNICATIONS article.
2) Using scan tool select BODY COMPUTER. If scan tool
displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool does not display NO RESPONSE, go to next step.
3) Operate door locks with Remote Keyless Entry (RKE)
transmitter. If doors locked when transmitter was actuated, system is
currently functioning properly. If doors do not lock when transmitter
was actuated, go to next step.
4) Ensure transmitter battery voltage is 3.2 volts. Turn
ignition on. Place transmission in park and disarm anti-theft system.
Using scan tool, select MISCELLANEOUS, then PROGRAM RKE. If BCM IS IN
PROGRAMMING MODE does not appear, exit and select PROGRAM RKE again.
Press any transmitter button. A single chime will announce RKE module
accepted transmission. Repeat procedure for all transmitters used with
vehicle. Operate door locks from reprogrammed transmitter. If door
locks operate properly, system has been repaired. If door locks do not
operate properly, go to next step.
5) Using scan tool, reprogram a known good transmitter:
Operate door locks with reprogrammed transmitter. If doors locked
properly, replace transmitter. If doors did not lock properly, replace
CTM.

right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external voltmeter, measure voltage between ground and
CTM 18-pin connector C2 terminal No. 18 (Black/Red wire). If voltage
is more than 9.5 volts, replace CTM. If voltage is 9.5 volts or less,
repair open in Black/Red wire between CTM and horn relay.
6) Remove security relay from Power Distribution Center
(PDC). Turn ignition on. Connect a test light between battery source
and headlight relay connector terminal No. 85 (Red/Dark Blue wire).
Using scan tool, actuate relay. If test light illuminates, replace
security relay. If test light does not illuminate, go to next step.
7) Using an external voltmeter, measure voltage between
battery voltage and security relay connector terminal No. 86
(Red/Orange wire). If voltage is more than 9.5 volts, go to next step.\
If voltage is 9.5 volts or less, repair open in Red/Orange wire
between battery source and security relay.
8) Reinstall security relay. Locate Central Timer Module
(CTM). CTM is located behind right kick panel. Disconnect CTM 18-pin
connector C2. Using an external voltmeter, measure voltage between
ground and CTM 18-pin connector C2 terminal No. 6 (Red/Dark Blue
wire). If voltage is more than 9.5 volts, replace CTM. If voltage is
9.5 volts or less, repair open in Red/Dark Blue wire between CTM and
security relay.
9) Disconnect overhead console 12-pin connector. Using an
external voltmeter, measure voltage between battery and overhead
console 12-pin connector terminal No. 11 (Black wire). Using scan
tool, actuate VTSS indicator light. If voltage is about 10 volts,
replace overhead console. If voltage is not about 10 volts, go to next
step.
10) Measure voltage between ground and overhead console 12-
pin connector terminal No. 5 (Pink wire). Turn ignition on. If voltage\
is more than 10 volts, go to next step. If voltage is 10 volts or
less, repair open Pink wire.
11) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external ohmmeter, measure resistance between ground and
CTM 18-pin connector C2 terminal No. 8 (Black wire). If resistance is
5 ohms or more, replace CTM. If resistance is less than 5 ohms, repair
open Black wire between CTM and VTSS indicator light.
12) Using scan tool, place VTSS in diagnostic mode and follow
directions on screen. If TURN KEY TO ACC POSITION is not displayed, go
to step 24). If NO RESPONSE after turning key to accessory position or
TURN KEY TO ACC POSITION is displayed longer than 15 seconds, go to
next step. If neither response is received, go to step 14).
13) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Gain access to CTM 18-pin connector C2. Ensure key
is in accessory position. Using an external voltmeter, measure voltage
between ground and backprobe of CTM 18-pin connector C2 terminal No. 5
(Dark Blue/White wire). If voltage is more than 10 volts, replace CTM.\
If voltage is 10 volts or less, repair open Dark Blue/White wire
between CTM and junction block.
14) Remove key from ignition. Wait 2 seconds after performing
each of the following actions. Open, then close both door. Operate
power door lock switch to lock, then unlock position. Rotate key both
directions in both doors. Ensure each operation is successful. If any
operation is unsuccessful, see VTSS SYMPTOM DIRECTORY table for repair
of failed operation. If all operations are successful, go to step 22).
VTSS SYMPTOM DIRECTORY









\









\









\









\









\









\









\








Problem Circuit Go To
Driver's Door Open Or Close ............................... Step 15)

CO M PU TE R R ELE A R N P R O CED URES

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
DaimlerChrysler Computer Relearn Procedures
INTRODUCTION
Vehicles equipped with engine or transmission/transaxle
computers may require a computer relearn procedure after the vehicle
battery is disconnected. Vehicle computers memorize and store vehicle
operation patterns for optimum driveability and performance. When the
vehicle battery is disconnected, this memory is lost, resulting in a
driveability problem. Depending on the vehicle and how it is equipped,
the following driveability problems may exist:
* Rough or unstable idle.
* Hesitation or stumble.
* Rich or lean running.
* Poor fuel mileage.
* Harsh or poor transmission/transaxle shift quality.
Default data is used until NEW data from each key start is
stored. As the computer restores its memory from each new key start,
driveability is restored.
Driveability problems may occur during the computer relearn
stage. To accelerate computer relearn process after battery removal
and installation, specified computer relearn procedures should be
performed. See appropriate procedures under specified manufacturer.
COMPUTER RELEARN PROCEDURES
ALL MODELS
NOTE: Read all procedures listed to determine why each procedure is
to be performed before proceeding.
Vehicle Driveability Computer Relearn Procedure
Manufacturer does not provide a specified computer relearn
procedure for obtaining proper driveability. If vehicle battery was
disconnected or Powertrain Control Module (PCM) was replaced, driving
the vehicle will enable the PCM to perform a computer relearn
procedure for obtaining proper driveability. Inform customer that
driveability may differ from what they are accustomed to until the PCM
completes the computer relearn procedure.
NOTE: If Powertrain Control Module (PCM) was replaced, the correct
vehicle mileage and Vehicle Identification Number (VIN) must
be programmed into the PCM to prevent Diagnostic Trouble
Codes (DTCs) from being set in the Anti-Lock Brake System
(ABS) module and Supplemental Restraint System (SRS) module\
.
To program PCM and clear DTCs from ABS and SRS modules,
proceed to appropriate procedure listed. If replacing
Powertrain Control Module (PCM) on models equipped with a
Smart Key Immobilizer Module (SKIM), the secret key data must\
also be updated to enable engine starting. To update secret
key data, proceed to appropriate procedure listed.
Programming PCM & Clearing DTCs From ABS & SRS Modules
Connect scan tool to Data Link Connector (DLC) below driver's\
side of instrument panel. Using scan tool, enter correct VIN and
mileage into PCM. Using scan tool manufacturer's instructions, clear