Page 2473 of 3115
B06412
B06415
Drain Plug
B06413Drain Plug
- MAINTENANCECHASSIS
MA-9
57 Author: Date:
(b) Differential:
Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole. If the level is low, add oil
until it begins to run out of the filler hole.
Front differential oil: See page SA-35
Rear differential oil: See page SA-95
8. REPLACE AUTOMATIC TRANSMISSION FLUID (See
page AT-3-1)
9. REPLACE TRANSFER AND DIFFERENTIAL OIL
(a) Remove the drain plug and drain the oil.
(b) Reinstall the drain plug securely.
(c) Add new oil until it begins to run out of the filler hole.
Transfer oil: See page TR-6
Front differential oil: See page SA-35
Rear differential oil: See page SA-95
10. REPACK FRONT WHEEL BEARINGS AND DRIVE
SHAFT BUSHING GREASE
(a) Change the front wheel bearing grease (See page
SA-16).
NOTICE:
Maintenance free for rear wheel bearing.
(b) Repack the drive shaft bushing grease (See page
SA-33).
11. LUBRICATE PROPELLER SHAFT AND TIGHTEN
BOLTS
(a) Lubricate chassis components, referring to the lubrication
chart. Before pumping in grease, wipe off any mud and
dust on the grease fitting.
Page 2479 of 3115
MA02R-05
MA-4
- MAINTENANCEUNDER HOOD
52 Author: Date:
2004 LAND CRUISER (RM1071U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTICE
Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance services after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the LEVEL lines on the see-through reservoir at normal tem-
perature (20°C (68°F)).
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(See page CO-14)
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check the indicator.
When the indicator color is blue, the condition is satisfactory. A red color indicates that distilled water
must be added, and white indicates that charging is necessary.
6. BRAKE FLUID LEVELS
Check that the brake fluid level is near the upper level line on the see-through reservoir.
(See page BR-4)
7. ENGINE DRIVE BELTS
Check drive belt for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
Check the level on the dipstick.
The level should be in the ºHOTº or ºCOLDº range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
Visually check the overflow plug and oil pan for fluid leaks or traces of fluid.
Page 2487 of 3115
PP1BR-03
PP-32
- PREPARATIONAUTOMATIC TRANSMISSION
91 Author: Date:
2004 LAND CRUISER (RM1071U)
LUBRICANT
ItemCapacityClassification
Automatic transmission fluid
Dry fill
Drain and refill
10.6 liters (11.2 US qts, 9.3 lmp qts)
3.0 liters (3.2 US qts, 2.6 lmp qts)ATF WS
Page 2594 of 3115
SS0OR-1 1
SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
148 Author: Date:
2004 LAND CRUISER (RM1071U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Fan shroud x Radiator assembly55144 in.´lbf
Radiator bracket x Radiator assembly Bolt
Nut18
20185
20013
15
A/C Compressor x Cylinder block4950036
Generator x Generator bracket3940029
No.1 idler pulley, No.2 idler pulley x Cylinder Block34.535025
Camshaft timing pulley x Camshaft timing tube1081,10080
Drive belt tensioner x Cylinder block1616012
Timing belt tensioner x Oil pump2627019
Crankshaft pulley x Crankshaft2452,500181
Fan bracket x Cylinder block 12 mm head
14 mm head16
32160
33012
24
No.2 timing belt cover x Cylinder block1616012
No.3 timing belt cover x Cylinder block, cylinder head7.58066 in.´lbf
Drive belt idler pulley x Fan bracket3940029
Fluid coupling x Fan bracket2121516
Exhaust manifold x Cylinder head4445033
Cylinder head x Cylinder block 1st
2nd
3rd32
Turn 90°
Turn 90°325
Turn 90°
Turn 90°24
Turn 90°
Turn 90°
Camshaft bearing cap x Cylinder head Bolt C
Others7.5
1680
16066 in.´lbf
12
Cylinder head cover x Cylinder head6.06053 in.´lbf
Engine hanger x Cylinder head3738027
Front water bypass joint, Rear water bypass joint x Cylinder head1818513
Intake manifold x Cylinder head1818513
V-bank cover bracket x Intake manifold7.58066 in.´lbf
Timing belt rear plate x Cylinder head7.58066 in.´lbf
Drive plate x Crankshaft 1st
2nd49
Turn 90°500
Turn 90°36
Turn 90°
Transmission x Cylinder block7273053
Transmission x No.1 oil pan3738027
Drive plate x Torque converter clutch4849035
Flywheel housing under cover x Transmission1818513
Frame crossmember x Body5051037
Frame crossmember x Rear engine mounting insulator7475055
Frame bracket x Engine mounting bracket3031022
PS pump x Cylinder head6263246
A/C compressor x Cylinder block, Fan bracket4950036
Main bearing cap x Cylinder block 1st
2nd27
Turn 90°275
Turn 90°20
Turn 90°
Connecting rod cap x Connecting rod 1st
2nd24.5
Turn 90°250
Turn 90°18
Turn 90°
Rear oil seal retainer x Cylinder block8.08071 in.´lbf
Engine coolant drain union x Cylinder block4950036
