1998 TOYOTA LAND CRUISER steering

H20912
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS-19
2294 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3. Vehicle involved in collision and airbag is deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
(a) Do a diagnostic system check (See page DI-692).
(b) Do a visual check which includes the following items with
the steering wheel pad (with airbag) removed from the ve-
hicle.

Check that the metal part where the steering wheel
pad is to be installed is not deformed.

Check the damage on the spiral cable connector
and wire harness.
HINT:

Do not repair the metal part where the steering wheel pad
is to be installed even if any deformation is found. Always
replace the steering wheel assembly with a new one.

There should be no interference between the steering
wheel pad and steering wheel, and the clearance should
be uniform all the way around when the new steering
wheel pad is installed on the steering wheel.

RS0BD-08
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS-29
2304 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
HINT:
For step 1 to 9, refer to page SR-24.
1. INSTALL SPIRAL CABLE
2. INSTALL COLUMN UPPER AND LOWER COVERS
3. INSTALL LOWER NO. 1 PANEL
4. INSTALL INSTRUMENT CLUSTER FINISH PANEL
5. INSTALL FRONT DOOR OPENING TRIM LH
6. INSTALL COWL SIDE TRIM LH
7. INSTALL FRONT DOOR SCUFF PLATE LH
8. INSTALL STEERING WHEEL
9. INSTALL STEERING WHEEL PAD
10. INSPECT SRS WARNING LIGHT (See page DI-692)

RS0B9-10
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS-17
2292 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
HINT:
For step 1 to 9, refer to page SR-14.
1. REMOVE STEERING WHEEL PAD
2. REMOVE STEERING WHEEL
3. REMOVE FRONT DOOR SCUFF PLATE LH
4. REMOVE COWL SIDE TRIM LH
5. REMOVE FRONT DOOR OPENING TRIM LH
6. REMOVE INSTRUMENT CLUSTER FINISH PANEL
7. REMOVE LOWER NO. 1 PANEL
8. REMOVE COLUMN UPPER AND LOWER COVERS
9. REMOVE SPIRAL CABLE

RS0SM-01
RS-28
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
2303 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the steering wheel pad, steering wheel or spiral cable.
CaseReplacing part
If the airbag has been deployed.Steering wheel pad
If the steering wheel pad has been found to be faulty in troubleshooting.Steering wheel pad
If the spiral cable has been found to be faulty in troubleshooting.Spiral cable
If the steering wheel pad has been found to be faulty during checking items
(See page RS-18).Steering wheel pad
If the steering wheel has been found to be faulty during checking items (See
page RS-18).Steering wheel
If the spiral cable has been found to be faulty during checking items (See
page RS-18).Spiral cable
If the steering wheel pad has been dropped.Steering wheel pad
CAUTION:
For removal and installation of the steering wheel pad, see page SR-14 and SR-24, and be sure to
follow the correct procedure.

RS0BU-07
H19947
Front Airbag Sensor LHFront Airbag Sensor RHFront Passenger
Airbag Assembly
Seat Belt
Pretensioner RH
Airbag Sensor Assembly Seat Belt
Pretensioner LHSpiral Cable
Curtain Shield Airbag
Sensor Assembly LHCurtain Shield Airbag
Sensor Assembly RH Side and Curtain Shield Airbag
Sensor Assembly LH
Side and Curtain Shield Airbag
Sensor Assembly RH Side Airbag Assembly LHSide Airbag Assembly RH Curtain Shield Airbag
Assembly LH
Curtain Shield Airbag
Assembly RH Steering Wheel Pad
(w/ Airbag)
RSCA Off
Switch
Seat Position Sensor
Assembly
RS-96
- SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
2371 Author
: Date
:
2004 LAND CRUISER (RM1071U)
WIRE HARNESS AND CONNECTOR
LOCATION

F04811
Vacuum HoseSR0LZ-06
SR-8
- STEERINGAIR CONTROL VALVE
2217 Author
: Date
:
2004 LAND CRUISER (RM1071U)
AIR CONTROL VALVE
INSPECTION
1. TURN AIR CONDITIONING SWITCH OFF
2. CHECK IDLE-UP
(a) Start the engine and run it at idle.
(b) Fully turn the steering wheel.
(c) Check that the engine rotations decrease when the vacu-
um hose of the air control valve is pinched.
(d) Check that the engine rotations increase when the hose
is released.

P06717
SR0LW-04
- STEERINGDRIVE BELT
SR-3
2212 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DRIVE BELT
INSPECTION
INSPECT DRIVE BELT
Visually check the belt for excessive wear, frayed cords, etc.
If any defect has been found, replace the drive belt.
HINT:
Cracks on the rib side of a belt are considered acceptable. If the
belt has chunks missing from the ribs, it should be replaced.

SR0LX-04
R11229
Normal Abnormal SR-4
- STEERINGPOWER STEERING FLUID
2213 Author
: Date
:
2004 LAND CRUISER (RM1071U)
POWER STEERING FLUID
BLEEDING
1. CHECK FLUID LEVEL (See page SR-5)
2. JACK UP FRONT OF VEHICLE AND SUPPORT IT
WITH STANDS
3. TURN STEERING WHEEL
With the engine stopped, turn the wheel slowly from lock to lock
several times.
4. LOWER VEHICLE
5. START ENGINE
Run the engine at idle for a few minutes.
6. TURN STEERING WHEEL
(a) With the engine idling, turn the wheel to left or right full
lock position and keep it there for 2-3 seconds, then turn
the wheel to the opposite full lock position and keep it
there for 2-3 seconds.
(b) Repeat (a) several times.
7. STOP ENGINE
8. CHECK FOR FOAMING OR EMULSIFICATION
If the system has to be bled twice specifically because of foam-
ing or emulsification, check for fluid leaks in the system.
9. CHECK FLUID LEVEL (See page SR-5)