1998 TOYOTA LAND CRUISER AUX
[x] Cancel search: AUXPage 180 of 3115
01*6
(Communica-
tion Control)D7 Connection
Check ErrorComponent in which this code is re-
corded has been disconnected from
system after engine start.
Or, when this code was recorded,
radio receiver assembly was dis-
connected. Check harness for power supply of
radio receiver assembly.
Check harness for communication
system of radio receiver assembly.
Check harness for power supply of
stereo component amplifier.
Check harness for communication
system of stereo component ampli-
fier.
Transmission
Error DC
*2 01
(Communication
Control)Transmission to component shown
by auxiliary code has bee failed.
(This code does not necessarily
mean actual failure.)If same auxiliary code is recorded in
other component(s), check harness
for power supply and communica-
tion system of components shown
sub code.
Master Reset
(Momentary
Interruption) DD
*3 01
(Communication
Control) Check harness for power supply
of radio receiver assembly.
Check harness for communica-
tion system of radio receiver as-
sembly.
If error occurs frequently, replace
radio receiver assembly.
Registration
Completion
Instruction
Error E0
*1 01
(Communication
Control)ºRegistration Completion Instruc-
tionº command fromradio receiver
assembly cannot be received.Since this DTC is provided for engi-
neering, it may be detected when
no actual failure exists.
ON/OFF
Instruction
Parameter
Error E2 01
(Communication
Control)Error is detected in ON/OFF control
command from radio receiver as-
sembly.Replace radio receiver assembly.
Registration
Request
Transmission E3 01
(Communication
Control)Since this DTC is provided for engi-
neering, it may be detected when
no actual failure exists. Registration Request command
is output from slave component.
By reception of connection check
Instruction, Registration Request
command is output from sub-mas-
ter component.After engine is started, radio receiv-
er assembly assembly was discon-
nected from system.
Master Error DF
*4 01
(Communication
Control)Due to defective condition of com-
ponent with a display, master func-
tion is switched to audio equip-
ment . Error occurs in communica-
tion between sub-master (audio)
and master component. Check harness for power supply
of radio receiver assembly.
Check harness for communica-
tion system of radio receiver as-
sembly.
Check harness for communica-
tion system between radio receiver
assembly and sub-master compo-
nent.
Audio proces-
sor ON error E1
*1 01
(Communication
Control)While source equipment is operat-
ing, AMP output is stopped. Check harness for power supply of
radio receiver assembly
Check harness for communication
system of radio receiver assembly.
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists. BE-144
- BODY ELECTRICALAUDIO SYSTEM
2517 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 181 of 3115
Physical address: 1F4 RSA Panel (Main AVC-LAN)
01
(Communica-
tion Control)D6
*1Absence of
MasterComponent in which this code is re-
corded has been disconnected from
system with ignition in ACC or ON.
Or, when this code was recorded, ra-
dio receiver assembly was discon-
nected. Check harness for power supply of
radio receiver assembly.
Check harness for communication
system of radio receiver assembly.
Check harness for power supply of
RSA panel.
Check harness for communication
system of RSA panel. HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Logical addressDTC
Diagnosis itemDiagnosis content
Countermeasure and inspeced parts
Transmission
Error DC
*2 01
(Communication
Control)Transmission to component shown
by auxiliary code has bee failed.
(This code does not necessarily
mean actual failure.)If same auxiliary code is recorded in
other component(s), check harness
for power supply and communica-
tion system of components shown
sub code.
Master Reset
(Momentary
Interruption) DD
*3 01
(Communication
Control) Check harness for power supply
of radio receiver assembly.
Check harness for communica-
tion system of radio receiver as-
sembly.
If error occurs frequently, replace
radio receiver assembly.
Registration
Completion
Instruction
Error E0
*1 01
(Communication
Control)ºRegistration Completion Instruc-
tionº command fromradio receiver
assembly cannot be received.Since this DTC is provided for engi-
neering, it may be detected when
no actual failure exists.
Registration
Request
Transmission E3 01
(Communication
Control)Since this DTC is provided for engi-
neering, it may be detected when
no actual failure exists. Registration Request command
is output from slave component.
By reception of connection check
Instruction, Registration Request
command is output from sub-mas-
ter component. After engine is started, radio receiv-
er assembly was disconnected
from system.
Master Error DF
*4 01
(Communication
Control)Due to defective condition of com-
ponent with a display, master func-
tion is switched to audio equip-
ment . Error occurs in communica-
tion between sub-master (audio)
and master component. Check harness for power supply
of radio receiver assembly.
Check harness for communica-
tion system of radio receiver as-
sembly.
Check harness for communica-
tion system between radio receiver
assembly and sub-master compo-
nent.
01*6
(Communica-
tion Control)D7 Connection
Check ErrorComponent in which this code is re-
corded has been disconnected from
system after engine start.
Or, when this code was recorded,
radio receiver assembly was dis-
connected. Check harness for power supply of
radio receiver assembly.
Check harness for communication
system of radio receiver assembly.
Check harness for power supply of
RSA panel.
Check harness for communication
system of RSA panel.
- BODY ELECTRICALAUDIO SYSTEM
BE-145
2518 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 182 of 3115
No Response
to Connection
Check 01 *3
(Communication
Control)Component shown by auxiliary code
is or had been disconnected from
system after engine start.
D9 Check harness for power supply
system of component shown by
auxiliary code.
Check harness for communica-
tion system of component shown by
auxiliary code. D8
Last Mode Error 01 *2
(Communication
Control)Component operated (sounds and/
or images were provided) before en-
gine stop is or has been discon-
nected with ignition switch in ACC or
ON. Check harness for power supply
system of component shown by
auxiliary code.
Check harness for communica-
tion system of component shown by
auxiliary code. D9
No Response
to ON/OFF
InstructionNo response is identified when
changing mode (audio and visual
mode change). Detected when
sound and picture does not change
by button operation. DA 01
(Communication
Control) Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
If error occurs again, replace
component shown by auxiliary
code.
Mode Status
Error DB 01 *2
(Communication
Control)Dual alarm is detected. Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
Physical address: 16A, 16C RSA Panel (Sub AVC-LAN)
Transmission
Error DC 01 *4
(Communication
Control)Transmission to component shown
by auxiliary code has been failed.
(Detecting this DTC does not nec-
essary mean actual failure.) If same auxiliary code is recorded
in other component, check harness
for power supply and communica-
tion system of components shown
sub code.
Slave Reset
(Momentary
Interruption) DE 01 *3
(Communication
Control)After engine is started, slave com-
ponent was disconnected from sys-
tem. Check harness for power supply
of component shown by auxiliary
code.
Check harness for communica-
tion system of component shown by
auxiliary code.
HINT:
*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.
*2: It may be stored when the engine key is turned 1 min. angain after engine start.
*3: It may be stored when the engine key is turned again after engine start.
*4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition
switch in ACC or ON, this code is stored.
Logical addressDTC
Diagnosis itemDiagnosis content
Countermeasure and inspeced parts
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
Plural Frame
Abort E4 01
(Communication
Control)Plural frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
BE-146
- BODY ELECTRICALAUDIO SYSTEM
2519 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 184 of 3115
ON/OFF
Instruction
Parameter
Error E2 01
(Communication
Control)Error is detected in ON/OFF control
command from DVD player.Replace DVD player.
Registration
Request
Transmission E3 01
(Communication
Control)Since this DTC is provided for engi-
neering, it may be detected when
no actual failure exists. Registration Request command
is output from slave component.
Registration connection check
Instruction, Registration Request
command is output from sub-mas-
ter component.
Multiple Frame
Abort E4 01
(Communication
Control)
Multiple frame transmission is
aborted.Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
01
(Communica-
tion Control)22 RAM ErrorAbnormal condition of RAM is
detected.Replace DVD player.
Physical address: 250 (DVD Auto Changer) (Sub AVC-LAN)
01
(Communica-
tion Control)D6
*1Absence of
MasterComponent in which this code is re-
corded has been disconnected from
system with ignition in ACC or ON.
Or, when this code was recorded, ra-
dio receiver assembly was discon-
nected. Check harness for power supply of
radio receiver assembly.
Check harness for communication
system of radio receiver assembly.
Check harness for power supply of
DVD auto changer.
Check harness for communication
system of DVD auto changer. Logical addressDTC
Diagnosis itemDiagnosis content
Countermeasure and inspeced parts
01*6
(Communica-
tion Control)D7 Connection
Check ErrorComponent in which this code is re-
corded has been disconnected from
system after engine start.
Or, when this code was recorded,
radio receiver assembly was dis-
connected. Check harness for power supply of
radio receiver assembly.
Check harness for communication
system of radio receiver assembly.
Check harness for power supply of
DVD auto changer.
Check harness for communication
system of DVD auto changer.
Transmission
Error DC
*2 01
(Communication
Control)Transmission to component shown
by auxiliary code has bee failed.
(This code does not necessarily
mean actual failure.)If same auxiliary code is recorded in
other component(s), check harness
for power supply and communica-
tion system of components shown
sub code.
Master Reset
(Momentary
Interruption) DD
*3 01
(Communication
Control) Check harness for power supply
of radio receiver assembly.
Check harness for communica-
tion system of radio receiver as-
sembly.
If error occurs frequently, replace
radio receiver assembly. After engine is started, radio receiv-
er assembly assembly was discon-
nected from system.
BE-148
- BODY ELECTRICALAUDIO SYSTEM
2521 Author: Date:
2004 LAND CRUISER (RM1071U)
Page 2470 of 3115
MA02V-02
- MAINTENANCEBODY
MA-1 1
59 Author: Date:
2004 LAND CRUISER (RM1071U)
BODY
INSPECTION
1. TIRE ROTATION
Check the owner's manual supplement in which the maintenance schedule is shown.
2. FINAL INSPECTION
(a) Check the operation of the body parts:
Hood:
Auxiliary catch operates properly
Hood locks securely when closed
Front and rear doors:
Door locks operate properly
Doors close properly
Back door:
Door lock operates properly
Seats:
Seat adjusts easily and locks securely in any position
Front seat back locks securely in any position
Folding-down rear seat backs look securely.
(b) Be sure to deliver a clean car. Especially check:
Steering wheel
Shift lever knob
All switch knobs
Door handles
Seats