1998 TOYOTA 4RUNNER warning

4RUNNER (1998)
Tire surface and wheel nuts
Check the tires carefully for cuts,
damage or excessive wear. See Chap-
ter 7- 2 for additional information.
When checking the tires, make sure
no nuts are missing, and check the
nuts for looseness. Tighten them if
necessary.
Tire rotation
Rotate the tires every 12000 km (7500
miles). See Chapter 7- 2 for additional
information.
Fluid leaks
Check underneath for leaking fuel, oil,
water or other fluid after the vehicle
has been parked for a while. If you
smell fuel fumes or notice any leak,
have the cause found and corrected
immediately.
Doors and engine hood
Check that all doors including back
door operate smoothly and all latches
lock securely. Make sure the engine
hood secondary latch secures the
hood from opening when the primary
latch is released. INSIDE THE VEHICLE
Items listed below should be
checked regularly, e.g. while per-
forming periodic services, cleaning
the vehicle, etc.
Lights
Make sure the headlights, stop lights,
tail lights, turn signal lights, and other
lights are all working. Check headlight
aim.
Service reminder indicators and
warning buzzers
Check that all service reminder indica-
tors and warning buzzers function
properly.
Steering wheel
Check that it has the specified free-
play. Be alert for changes in steering
condition, such as hard steering or
strange noise.
Seats
Check that all seat controls such as
seat adjusters, seatback recliner, etc.
operate smoothly and that all latches
lock securely in any position. Check
that the head restraint move up and
down smoothly and that the locks hold
securely in any latched position. For
folding- down rear seatbacks, swing- up
rear seat cushions and detachable
temporary third seat, check that the
latches lock securely.Seat belts
Check that the seat belt system such
as buckles, retractors and anchors op-
erate properly and smoothly. Make
sure the belt webbing is not cut,
frayed, worn or damaged.
Accelerator pedal
Check the pedal for smooth operation
and uneven pedal effort or catching.
Clutch pedal
Check the pedal for smooth operation.
Brake pedal
Check the pedal for smooth operation
and that the pedal has the proper
clearance. Check the brake booster
function.
Brakes
At a safe place, check that the brakes
do not pull to one side when applied.
Parking brake
Check that the lever has the proper
travel and that, on a safe incline, your
vehicle is held securely with only the
parking brake applied.

4RUNNER (1998)
Replacement with used wheels is not
recommended as they may have been
subjected to rough treatment or high
mileage and could fail without warning.
Also, bent wheels which have been
straightened may have structural dam-
age and therefore should not be used.
Never use an inner tube in a leaking
wheel which is designed for a tube-
less tire. Aluminum wheel precautions
After driving your vehicle the first
1600 km (1000 miles), check that
the wheel nuts are tight.
If you have rotated, repaired or
changed your tires, check that the
wheel nuts are still tight after driv-
ing 1600 km (1000 miles).
When using tire chains, be careful
not to damage the aluminum
wheels.
Use only the Toyota wheel nuts
and wrench designed for your alu-
minum wheels.
When balancing your wheels, use
only Toyota balance weights or
equivalent and a plastic or rubber
hammer.
As with any wheel, periodically
check your aluminum wheels for
damage. If damaged, replace im-
mediately.

4RUNNER (1998)
J80003
Instrument panel
14. HEAD(LH) 10 A: Left- hand head-
light
15. DRL 7.5 A: Daytime running light
system
16. HEAD (LO RH) 10 A: Right- hand
headlight(low beam)
17. HEAD (LO LH) 10 A: Left- hand
headlight(low beam)
18. HEAD (HI RH) 10 A: Right- hand
headlight(high beam)
19. HEAD (HI LH) 10 A: Left- hand
headlight(high beam)
20. ACC 15 A: Car audio system, pow-
er antenna, clock, power rear view
mirror control 21. ECU- B 7.5 A:
SRS airbag warning
light
22. 4WD 20 A: A.D.D. control system,
four- wheel drive control system,
rear differential lock system
23. TURN 10 A: Turn signals lights,
emergency flashers
24. GAUGE 10 A: Gauges and meters,
back window defogger, daytime
running light system, air condition-
ing system, electric moon roof
25. ECU- IG 10 A: cruise control sys-
tem, anti- lock brake system, elec-
tronically controlled automatic
transmission system, power anten-na
26. WIPER 20 A: windshield wipers
and washer, back window wiper 27. IGN 7.5 A:
SRS airbag system,
multiport fuel injection system / se-
quential multiport fuel injection sys-
tem, discharge warning light

4RUNNER (1998)
Uniform tire quality grading
This information has been prepared in
accordance with regulations issued by
the National Highway Traffic Safety
Administration of the U.S. Department
of Transportation. It provides the pur-
chasers and/or prospective purchasers
of Toyota vehicles with information on
uniform tire quality grading.
Your Toyota dealer will help answer
any questions you may have as you
read this information.
DOT quality gradesÐAll passenger
vehicle tires must conform to Fed-
eral Safety Requirements in addition
to these grades. These quality
grades are molded on the sidewall.
Treadwear ÐThe treadwear grade is a
comparative rating based on the wear
rate of the tire when tested under
controlled conditions on a specified
government test course. For example,
a tire graded 150 would wear one and
a half (1- 1/2) times as well on the
government course as a tire graded
100. The relative performance of tires
depends upon the actual conditions of
their use, however, and may depart
significantly from the norm due to
variations in driving habits, service
practices and differences in road char-
acteristics and climate. Traction A, B, C
ÐThe traction
grades, from highest to lowest, are A,
B, and C, and they represent the
tire's ability to stop on wet pavement
as measured under controlled condi-
tions on specified government test
surfaces of asphalt and concrete. A
tire marked C may have poor traction
performance.
Warning: The traction grade assigned
to this tire is based on braking
(straight ahead) traction tests and
does not include cornering (turning)
traction.
Temperature A, B, C ÐThe tempera-
ture grades are A (the highest), B,
and C, representing the tire's resis-
tance to the generation of heat and its
ability to dissipate heat when tested
under controlled conditions on a speci-
fied indoor laboratory test wheel. Sus-
tained high temperature can cause the
material of the tire to degenerate and
reduce tire life, and excessive temper-
ature can lead to sudden tire failure.
The grade C corresponds to a level of
performance which all passenger car
tires must meet under the Federal Mo-
tor Vehicle Safety Standard No. 109.
Grades B and A represent higher lev-
els of performance on the laboratory
test wheel than the minimum required
by law. Warning: The temperature grades for
this tire are established for a tire that
is properly inflated and not over-
loaded. Excessive speed, underinfla-
tion, or excessive loading, either sepa-
rately or in combination, can cause
heat buildup and possible tire failure.