1998 TOYOTA 4RUNNER flat tire

4RUNNER (1998)
A safety chain must always be
used between the towing vehicle
and the trailer. Leave sufficient
slack in the chain for turns. The
chain should cross under the
trailer tongue to prevent the
tongue from dropping to the
ground in case it becomes dam-
aged or separated. For correct
safety chain procedures, follow
the hitch or trailer manufactur-
er 's recommendations.
CAUTION
If the total trailer weight ex-
ceeds 453 kg (1000 lb.), trailer
brakes are required .
Never tap into your vehicle's
hydraulic system as it would
lower its braking effectiveness .
Never tow a trailer without us-
ing a safety chain securely atta-
ched to both the trailer and the
vehicle. If damage occurs to the
coupling unit or hitch ball,
there is danger of the trailer
wandering over into another
lane.
TIRES
Ensure that your vehicle's tires are
properly inflated. See Chapter 7- 2
for instructions.
The trailer tires should be inflated
to the pressure recommended by
the trailer manufacturer in respect
to the total trailer weight.
TRAILER LIGHTS Trailer lights must comply with fed-
eral, state/provincial and local re-
gulations. See your local recre-
ational vehicle dealer or rental
agency for the correct type of wir-
ing and relays for your trailer.
Check for correct operation of the
turn signals and stop lights each
time you hitch up. Direct splicing
may damage your vehicle's electri-
cal system and cause a malfunc-
tion of your lights.
BREAK- IN SCHEDULE Toyota recommends that you do
not tow a trailer with a new vehicle
or a vehicle with any new power
train component (engine, transmis-
sion, differential, wheel bearing,
etc.) for the first 800 km (500
miles) of driving. MAINTENANCE
If you tow a trailer, your vehicle
will require more frequent
maintenance due to the additional
load. For this information, please
refer to the scheduled maintenance
information in the ºOwner 's Manual
Supplement/Maintenance Scheduleº.
Retighten all fixing bolts of the
towing ball and bracket after
approximately 1000 km (600 miles)
of trailer driving.
PRE- TOWING SAFETY CHECK
Check that your vehicle remains
level when a loaded or unloaded
trailer is hitched. Do not drive if
the vehicle has an abnormal nose-
up or nose- down condition, and
check for improper tongue load,
overload, worn suspension or other
possible causes.
Make sure the trailer cargo is se-
curely loaded so that it cannot
shift.
Check that your rear view mirrors
conform to any applicable federal,
state/provincial or local regulation.
If not, install the rear view mirrors
required for towing purpose.

4RUNNER (1998)
Slow down and downshift be-
fore descending steep or long
downhill grades. Do not make
sudden downshifts.
Avoid holding the brake pedal
down too long or too frequent-
ly. This could cause the brakes
to overheat and result in re-
duced braking efficiency.Getting more kilometers/mileage from
a liter/gallon of fuel is easyÐjust take
it easy. It will help make your vehicle
last longer, too. Here are some specif-
ic tips on how to save money on both
fuel and repairs:
Keep your tires inflated at the
correct pressure. Underinflation
causes tire wear and wastes fuel.
See Chapter 7- 2 for instructions.
Do not carry unneeded weight in
your vehicle. Excess weight puts
a heavier load on the engine, caus-
ing greater fuel consumption.
Avoid lengthy warm- up idling.
Once the engine is running smooth-
ly, begin drivingÐbut gently. Re-
member, however, that on cold win-
ter days this may take a little
longer.
Accelerate slowly and smoothly.
Avoid jackrabbit starts. Get into
high gear as quickly as possible.
Avoid long engine idling. If you
have a long wait and you are not
in traffic, it is better to turn off the
engine and start again later.
Avoid engine lug or overrevving.
Use a gear position suitable for the
road on which you are travelling.
Avoid continuous speeding up
and slowing down. Stop- and- go
driving wastes fuel.
Avoid unnecessary stopping and
braking. Maintain a steady pace.
Try to time the traffic signals so
you only need to stop as little as
possible or take advantage of
through streets to avoid traffic
lights. Keep a proper distance from
other vehicles to avoid sudden
braking. This will also reduce wear
on your brakes.
Avoid heavy traffic or traffic
jams whenever possible.
Do not rest your foot on the
clutch or brake pedal. This
causes needless wear, overheating
and poor fuel economy.
Maintain a moderate speed on
highways. The faster you drive,
the greater the fuel consumption.
By reducing your speed, you will
cut down on fuel consumption.
Keep the front wheels in proper
alignment. Avoid hitting the curb
and slow down on rough roads.
Improper alignment not only causes
faster tire wear but also puts an
extra load on the engine, which, in
turn, wastes fuel.
How to save fuel and make
your vehicle last longer, to
o

4RUNNER (1998)
Part 4
IN CASE OF AN
EMERGENCY
If your vehicle will not start
If your engine stalls while
driving
If your vehicle overheats
If you have a flat tire
If your vehicle needs to be
towed
If you cannot shift automatic
transmission selector lever
If you lose your keys
Before making these checks, make
sure you have followed the correct
starting procedure given in ºHow to
start the engineº in Part 3 and that
you have sufficient fuel.
If the engine is not turning over or
is turning over too slowlyÐ
1. Check that the battery terminals are tight and clean.
2. If the battery terminals are O.K., switch on the interior light.
3. If the light is out, dim or goes out when the starter is cranked, the
battery is discharged. You may try
jump starting. See º(c) Jump start-
ingº for further instructions.
If the light is O.K., but the engine still
will not start, it needs adjustment or
repair. Call a Toyota dealer or quali-
fied repair shop.
NOTICE
Do not pull- or push- start the ve- hicle. It may damage the vehicleor cause a collision when the en-
gine starts. Also the three- way
catalytic converter may overheatand become a fire hazard.
If the engine turns over at its nor-
mal speed but will not startÐ
1. Check that all the push- on connec- tors are tight. (For example, con-
nections at the spark plugs, ignition
coil and/or distributor)
2. If the connectors are O.K., the en- gine may be flooded because of
repeated cranking. See º(b) Start-
ing a flooded engineº for further
instructions.
If your vehicle will not start
Ð
(a) Simple checks

4RUNNER (1998)
3. Visually check to see if the engine drive belt (fan belt) is broken or
loose. Look for obvious coolant
leaks from the radiator, hoses, and
under the vehicle. However, note
that water draining from the air
conditioning is normal if it has
been used.
CAUTION
When the engine is running, keep
hands and clothing away from the
moving fan and engine drive
belts.
4. If the engine drive belt is brokenor the coolant is leaking, stop the
engine immediately. Call a Toyota
dealer for assistance.
5. If the engine drive belt is O.K. and there are no obvious leaks, you
may help the engine cool down
more quickly by running it at about
1500 rpm for a few minutes with
the accelerator pedal lightly de-
pressed.
6. Check the coolant reservoir. If it is dry, add coolant to the reservoir
while the engine is running. Fill it
about half full.
CAUTION
Do not attempt to remove the ra-
diator cap when the engine and
radiator are hot. Serious injury
could result from scalding hot
fluid and steam blown out under
pressure.
7. After the engine coolant tempera-ture has cooled to normal, again
check the coolant level in the res-
ervoir. If necessary, bring it up to
half full again. Serious coolant loss
indicates a leak in the system. You
should have it checked as soon as
possible at your Toyota dealer. If you have a flat tireÐ
1. Reduce your speed gradually, keep- ing a straight line. Move cautiously
off the road to a safe place well
away from the traffic. Avoid stop-
ping on the center divider of a
highway. Park on a level spot with
firm ground.
2. Stop the engine and turn on your emergency flashers.
3. Firmly set the parking brake and put the transmission in ºPº (auto-
matic) or reverse (manual).
4. Have everyone get out of the ve- hicle on the side away from traffic.
5. Read the following instructions thoroughly.
CAUTION
When jacking, be sure to observe
the following to reduce the possi-
bility of personal injury: Follow jacking instructions.
Do not start or run the engine
while your vehicle is supported
by the jack.

4RUNNER (1998)
Stop the vehicle on a level firm
ground, firmly set the parking
brake and put the transmission
in ºPº (automatic) or reverse
(manual). Block the wheel diag-
onally opposite to the one be-
ing changed if necessary.
Make sure to set the jack prop-
erly in the jack point. Raising
the vehicle with jack improperly
positioned will damage the ve-
hicle or may allow the vehicle
to fall off the jack and cause
personal injury.
Never get under the vehicle
when the vehicle is supported
by the jack alone.
Use the jack only for lifting
your vehicle during wheel
changing.
Do not raise the vehicle with
someone in the vehicle.
When raising the vehicle, do
not put an object on or under
the jack.
Raise the vehicle only high
enough to remove and change
the tire.NOTICE
Do not continue driving with a
deflated tire. Driving even a shortdistance can damage a tire be-yond repair.
ÐRequired tools and spare
tire

4RUNNER (1998)
2. Block the wheel diagonally oppo-
site the flat tire to keep the ve-
hicle from rolling when it is
jacked up.
When blocking the wheel, place a
wheel block from the front for the
front wheels or from the rear for the
rear wheels. ÐRemoving wheel ornament

4RUNNER (1998)
6. After making sure that no one is
in the vehicle, raise it high
enough so that the spare tire
can be installed.
Remember you will need more ground
clearance when putting on the spare
tire than when removing the flat tire.
To raise the vehicle, insert the jack
handle extension in to the jack (it is
a loose fit) and turn it clockwise with
the handle, making sure the handle
remains firmly fitted onto the jack
handle extension. As the jack touches
the vehicle and begins to fit, double-
check that it is properly positioned.
CAUTION
Never get under the vehicle when
the vehicle is supported by the
jack alone.
ÐChanging wheels
7. Remove the wheel nuts and change tires.
Lift the flat tire straight off and put it
aside.

4RUNNER (1998)
10. Reinstall the wheel ornament.
Put the wheel ornament into position
and then tap it firmly with the side or
heel of your hand to snap it into
place.
CAUTION
Take due care in handling the or-
nament to avoid unexpected per-
sonal injury.
ÐAfter changing wheels
11. Check the air pressure of the re- placed tire.
Adjust the air pressure to the specifi-
cation designated in Part 8. If the
pressure is lower, drive slowly to the
nearest service station and fill to the
correct pressure.
Do not forget to reinstall the tire infla-
tion valve cap as dirt and moisture
could get into the valve core and
possibly cause air leakage. If the cap
is missing, have a new one put on as
soon as possible.
12. Restore all the tools, jack and flat tire securely. As soon as possible after changing
wheels, tighten the wheel nuts to the
torque specified in Part 8 with a
torque wrench and have a technician
repair the flat tire.
CAUTION
Before driving, make sure all the
tools, jack and flat tire are se-
curely in place in their storage
location to reduce the possibility
of personal injury during a colli-
sion or sudden braking.