1998 TOYOTA 4RUNNER height

4RUNNER (1998)
This vehicle is one of the class of
vehicles which have higher ground
clearance and narrower tread in
relation to the height of their center
of gravity to make them capable of
performing in a wide variety of off-
road applications. Specific design
characteristics give it a higher cen-
ter of gravity than ordinary cars. An
advantage of the higher ground
clearance is a better view of the
road allowing you to anticipate
problems. It is not designed for
cornering at the same speeds as
conventional two- wheel drive ve-
hicles any more than low- slung
sports cars are designed to perform
satisfactorily under off- road condi-
tions.

4RUNNER (1998)
Even if the power assist is
completely lost, the brakes will
still work. But you will have to
push the pedal hardÐmuch
harder than normal. And your
braking distance will be longer.
ANTI- LOCK BRAKE SYSTEM
(with ºABSº warning light)
The anti- lock brake system is de-
signed to automatically help prevent
lock- up of the wheels during sudden
braking or braking on slippery road
surfaces. This assists in providing
directional stab ility and steering per-
formance of the vehicle under these
circumstances.
The anti- lock brake system becomes
operative after the vehicle has accel-
erated to a speed in excess of
approximately 10 km/h (6 mph). It
stops operating when the vehicle de-
celerates to a speed below approxi-
mately 5 km/h (3 mph).
You may hear a sound in the engine
compartment for a few seconds when
the engine is started or just after the
vehicle is started. This means that the
anti- lock brake system is in the self
check mode, and does not indicate a
malfunction. Effective way to press the ºABSº
brake pedal: When the anti- lock brake
system function is in action, you may
feel the brake pedal pulsating and
hear a noise. In this situation, to let
the anti- lock brake system work for
you, just hold the brake pedal down
more firmly. Do not pump the brake.
This will result in reduced braking per-
formance.
The brake pedal pulsation caused by
the anti- lock brake system may indi-
cate hazardous road surface condi-
tions. Although the anti- lock brake
system assists in providing vehicle
control, it is still important to drive
with all due care, because the anti-
lock brake system cannot overcome
the laws of physics that act on your
vehicle:
Braking capab ility is dependent on
tire friction with the road surface.
Even though the anti- lock brake
system is operating, a driver can-
not maintain full control on certain
slippery road surfaces, when cor-
nering at high speeds, or in violent
maneuvers.
Avoid high speeds on wet roads.
The anti- lock brake system cannot
eliminate the risk of hydroplaning
and loss of tire friction. Always maintain a safe distance from
the vehicle in front of you. Compared
with vehicles not fitted with an anti-
lock brake system, your vehicle may
require a longer stopping distance in
the following cases:
Driving on rough, gravel or snow-
covered roads.
Driving with tire chains installed.
Driving on roads where the road
surface is pitted or has other differ-
ences in surface height.
CAUTION
Do not use tires other than the
manufacturer 's designated tires,
and do not mix tires or wheels of
different sizes. You may prevent
the antilock brake system from
operating at full effectiveness.
Vehicles with rear differential lock sys-
tem 'The anti- lock brake system does
not operate when the rear differential
is locked. It is normal operation for
the ºABSº warning light to be on at
this time.

4RUNNER (1998)
Part 3
STARTING AND
DRIVING
Before starting the engine
How to start the engine
Tips for driving in various
conditions
Off- road driving precautions
Winter driving tips
Tr ailer towing
How to save fuel and make
your
vehicle last longer, too
Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, seat cushion angle, head re-
straint height and steering wheel
angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts. 1. Apply the parking brake firmly.
2. Turn off unnecessary lights and ac-
cessories.
3. Manual transmission: Press the
clutch pedal to the floor and shift
the transmission into neutral. Hold
the clutch pedal to the floor until
the engine is started. A starter
safety device will prevent the start-
er from operating if the clutch ped-
al is not fully depressed.
Automatic transmission: Put the
selector lever in ºPº. If you need to
restart the engine while the vehicle
is moving, put the selector lever in
ºNº. A starter safety device will pre-
vent the starter from operating if the
selector lever is in any drive position.
4. Automatic transmission only: De-
press the brake pedal and hold it
to the floor until driving off.
How to start the engineÐ
(a) Before cranking

4RUNNER (1998)
CAUTION
Do not drive with the snow
tires incorrectly inflated.
Never drive over 120 km/h (75
mph) with any type of snow
tires.
TIRE CHAIN SELECTION
Use the tire chains of correct size.
Regulations regarding the use of
tire chains vary according to loca-
tion or type of road, so always
check them before installing chains.
CHAIN INSTALLATION
Install the chains on the rear tires
as tightly as possible. Do not use
tire chains on the front tires. Re-
tighten chains after driving 0.5Ð1.0
km (1/4Ð1/2 mile).
When installing chains on your tires,
carefully follow the instructions of the
chain manufacturer.
If wheel covers are used, they will be
scratched by the chain band, so re-
move the covers before putting on the
chains.
CAUTION
Do not exceed 50 km/h (30
mph) or the chain manufactur-
er 's recommended speed limit,
whichever is lower.
Drive carefully avoiding bumps,
holes, and sharp turns, which
may cause the vehicle to bounce.
Avoid sharp turns or locked-
wheel braking, as use of chains
may adversely affect vehicle
handling.
Replacing wheels
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion,
the wheel should be replaced.
If you fail to replace damaged wheels,
the tire may slip off the wheel or they
may cause loss of handling control.
WHEEL SELECTION
When replacing wheels, care should
be taken to ensure that the wheels
are replaced by ones with the same
load capacity, diameter, rim width,
and offset.
Correct replacement wheels are avail-
able at your Toyota dealer.
A wheel of a different size or type
may adversely affect handling, wheel
and bearing life, brake cooling,
speedometer/odometer calibration,
stopping ab ility, headlight aim, bumper
height, vehicle ground clearance, and
tire or snow chain clearance to the
body and chassis.