1998 TOYOTA 4RUNNER automatic transmission

4RUNNER (1998)
(b) Starting the engine
Before starting the engine, be sure to
follow the instructions in º(a) Before
crankingº.
Normal starting procedure
The multiport fuel injection system/se-
quential multiport fuel injection system
in your engine automatically controls
the proper air- fuel mixture for starting.
You can start a cold or hot engine as
follows:
1. With your foot off the accelerator
pedal, crank the engine by turning the
key to ºSTARTº. Release it when the
engine starts.
2. After the engine runs for about 10
seconds, you are ready to drive.
If the weather is below freezing, let
the engine warm up for a few minutes
before driving.
If the engine stalls...
Simply restart it, using the correct
procedure given in normal starting.
If the engine will not startÐ
See ºIf your vehicle will not startº in
Part 4.
NOTICE
Do not crank for more than 30 seconds at a time. This mayoverheat the starter and wiringsystems.
Do not race a cold engine.
If the engine becomes difficult
to start or stalls frequently,have the engine checked im-mediately.
Always slow down in gusty cross-
winds. This will allow you much
better control.
Drive slowly onto curbs and, if
possible, at a right angle. Avoid
driving onto high, sharp- edged ob-
jects and other road hazards. Fail-
ure to do so can lead to severe
tire damage resulting in tire bursts.
When parking on a hill, turn the
front wheels until they touch the
curb so that the vehicle will not
roll. Apply the parking brake, and
place the transmission in ºPº (auto-
matic) or in first or reverse (manu-
al). If necessary, block the wheels.
Washing your vehicle or driving
through deep water may get the
brakes wet. To see whether they
are wet, check that there is no
traffic near you, and then press the
pedal lightly. If you do not feel a
normal braking force, the brakes
are probably wet. To dry them,
drive the vehicle cautiously while
lightly pressing the brake pedal
with the parking brake pulled. If
they still do not work safely, pull to
the side of the road and call a
Toyota dealer for assistance.
Tips for driving in various
conditions

4RUNNER (1998)
Use a washer fluid containing an
antifreeze solution.
This product is available at your Toyo-
ta dealer and most auto parts stores.
Follow the manufacturer 's directions
for how much to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because itmay damage your vehicle's paint.
Do not use your parking brake
when there is a possibility it could
freeze.
When parking, put the transmission
into ºPº (automatic) or into first or
reverse (manual) and block the rear
wheels. Do not use the parking brake,
or snow or water accumulated in and
around the parking brake mechanism
may freeze, making it hard to release.
Keep ice and snow from accumulat-
ing under the fenders.
Ice and snow built up under your
fenders can make steering difficult.
During bad winter driving, stop and
check under the fenders occasionally. Depending on where you are driv-
ing, we recommend you carry some
emergency equipment.
Some of the things you might put in
the vehicle are tire chains, window
scraper, bag of sand or salt, flares,
small shovel, jumper cables, etc.
Trailer towing
Your vehicle is designed primarily as
a passenger- and- load- carrying ve-
hicle. Towing a trailer will have an
adverse effect on handling, perfor-
mance, braking, durability and driving
economy (fuel consumption, etc.).
Your safety and satisfaction depend
on the proper use of correct equip-
ment and cautious driving habits. For
your safety and the safety of others,
you must not overload your vehicle or
trailer. Ask your local Toyota dealer
for further details before towing.
WEIGHT LIMITS
Before towing, make sure the total
trailer weight, gross combination
weight, gross vehicle weight, gross
axle weight and trailer tongue load
are all within the limits.
The total trailer weight and tongue
load can be measured with platform
scales found at a highway weighing
station, building supply company,
trucking company, junk yard, etc.

4RUNNER (1998)
TRAILER TOWING TIPS
When towing a trailer, your vehicle
will handle differently than when
not towing. The three main causes
of vehicle- trailer accidents are driv-
er error, excessive speed and im-
proper trailer loading. Keep these in
mind when towing:
Before starting out, check operation
of the lights and all vehicle- trailer
connections. After driving a short
distance, stop and recheck the
lights and connections. Before ac-
tually towing a trailer, practice turn-
ing, stopping and backing with a
trailer in an area away from traffic
until you learn the feel.
Backing with a trailer is difficult
and requires practice. Grip the bot-
tom of the steering wheel and
move your hand to the left to move
the trailer to the left. Move your
hand to the right to move the trail-
er to the right. (This procedure is
generally opposite to that when
backing without a trailer). Also, just
turn the steering wheel a little at
a time, avoiding sharp or prolonged
turning. Have someone guide you
when backing to reduce the risk of
an accident.
Because stopping distance may be
increased, vehicle- to- vehicle dis-
tance should be increased when
towing a trailer. For each 16 km/h
(10 mph) of speed, allow at least
one vehicle and trailer length bet-
ween you and the vehicle ahead.
Avoid sudden braking as you may
skid, resulting in jackknifing and
loss of control. This is especially
true on wet or slippery surfaces.
Avoid jerky starts or sudden accel-
eration. If your vehicle has a
manual transmission, prevent ex-
cessive clutch slippage by keeping
engine rpm low and not racing the
engine. Always start out in first
gear.
Avoid jerky steering and sharp
turns. The trailer could hit your ve-
hicle in a tight turn. Slow down
before making a turn to avoid the
necessity of sudden braking.
Remember that when making a
turn, the trailer wheels will be clos-
er than the vehicle wheels to the
inside of the turn. Therefore, com-
pensate for this by making a larger
than normal turning radius with y-
our vehicle.
Crosswinds and rough roads will
adversely affect handling of your
vehicle and trailer, causing sway.
Pay attention to the rear from time
to time to prepare yourself for be-
ing passed by large trucks or
buses, which may cause your ve-
hicle and trailer to sway. If swaying
happens, firmly grip the steering
wheel and reduce speed immedi-
ately but gradually. Never increase
speed. Steer straight ahead. If you
make no extreme correction with
the steering or brakes, the vehicle
and trailer will stabilize.
Be careful when passing other ve-
hicles. Passing requires consider-
able distance. After passing a ve-
hicle, do not forget the length of
your trailer and be sure you have
plenty of room before changing
lanes.
In order to maintain engine braking
efficiency, do not use fifth gear
(manual transmission) or overdrive
(automatic transmission).

4RUNNER (1998)
Because of the added load of the
trailer, your vehicle's engine may
overheat on hot days (at tempera-
tures over 30 C [85 F]) when go-
ing up a long or steep grade with
a trailer. If the engine coolant tem-
perature gauge indicates overheat-
ing, immediately turn off the air-
conditioning (if in use), pull off the
road and stop in a safe spot. Refer
to ºIf your vehicle overheatsº in
Part 4 of this manual.
Always place wheel blocks under
both the vehicle and trailer wheels
when parking. Apply the parking
brake firmly. Put the transmission
in Pº (automatic) or in first or re-
verse (manual). Avoid parking on a
slope with a trailer, but if it cannot
be avoided, do so only after per-
forming the following:
1. Apply the brakes and hold.
2. Have someone place wheel blocks under both the vehicle and trailer
wheels.
3. When the wheel blocks are in place, release your brakes slowly
until the blocks absorb the load.
4. Apply the parking brake firmly. 5. Shift into first or reverse (manual)
or ºPº (automatic) and turn off the
engine. When restarting out after parking on
a slope:
1. With the transmission in ºPº posi- tion (automatic) or the clutch pedal
depressed (manual), start the en-
gine. (With an automatic transmis-
sion, be sure to keep the brake
pedal depressed.)
2. Shift into gear.
3. Release the parking brake (also foot brake on automatic transmis-
sion vehicles) and slowly pull or
back away from the wheel blo cks.
Stop and apply your brakes.
4. Have someone retrieve the blo cks.
CAUTION
Do not exceed 72 km/h (45
mph) or the posted towing
speed limit, whichever is lower.
Because instab ility (swaying) of
a towing vehicle- trailer com-
bination usually increases as
the speed increases, exceeding
72 km/h (45 mph) may cause
loss of control.

4RUNNER (1998)
Part 4
IN CASE OF AN
EMERGENCY
If your vehicle will not start
If your engine stalls while
driving
If your vehicle overheats
If you have a flat tire
If your vehicle needs to be
towed
If you cannot shift automatic
transmission selector lever
If you lose your keys
Before making these checks, make
sure you have followed the correct
starting procedure given in ºHow to
start the engineº in Part 3 and that
you have sufficient fuel.
If the engine is not turning over or
is turning over too slowlyÐ
1. Check that the battery terminals are tight and clean.
2. If the battery terminals are O.K., switch on the interior light.
3. If the light is out, dim or goes out when the starter is cranked, the
battery is discharged. You may try
jump starting. See º(c) Jump start-
ingº for further instructions.
If the light is O.K., but the engine still
will not start, it needs adjustment or
repair. Call a Toyota dealer or quali-
fied repair shop.
NOTICE
Do not pull- or push- start the ve- hicle. It may damage the vehicleor cause a collision when the en-
gine starts. Also the three- way
catalytic converter may overheatand become a fire hazard.
If the engine turns over at its nor-
mal speed but will not startÐ
1. Check that all the push- on connec- tors are tight. (For example, con-
nections at the spark plugs, ignition
coil and/or distributor)
2. If the connectors are O.K., the en- gine may be flooded because of
repeated cranking. See º(b) Start-
ing a flooded engineº for further
instructions.
If your vehicle will not start
Ð
(a) Simple checks

4RUNNER (1998)
CAUTION
When making the connections, to
avoid serious injury, do not lean
over the battery or accidentally
let the jumper cables or clamps
touch anything except the correct
battery terminals or the ground.
5. Start your engine in the normal
way. After starting, run it at about
2000 rpm for several minutes with
the accelerator pedal lightly de-
pressed.
6. Carefully disconnect the cables in the exact reverse order: the nega-
tive cable and then the positive
cable.
7. Carefully dispose of the battery cover clothsÐthey may now con-
tain sulfuric acid.
8. If removed, replace all the battery vent plugs.
If the cause of your battery discharg-
ing is not apparent (for example,
lights left on), you should have it
checked. If your engine stalls while driving...
1. Reduce your speed gradually, keep- ing a straight line. Move cautiously
off the road to a safe place.
2. Turn on your emergency flashers.
3. Try starting the engine again.
If the engine will not start, see ºIf
your vehicle will not startº.
CAUTION
If the engine is not running, the
power assist for the brakes and
steering will not work so steering
and braking will be much harder
than usual.
If your vehicle overheats
If your engine coolant temperature
gauge indicates overheating, if you
experience a loss of power, or if
you hear a loud knocking or ping-
ing noise, the engine has probably
overheated. You should follow this
procedure... 1. Pull safely off the road, stop the vehicle and turn on your emergen-
cy flashers. Put the transmission in
ºPº (automatic) or neutral (manual)
and apply the parking brake. Turn
off the air conditioning if it is being
used.
2. If coolant or steam is boiling out of the radiator or reservoir, stop the
engine. Wait until the steam sub-
sides before opening the hood. If
there is no coolant boiling over or
steam, leave the engine running.
CAUTION
To help avoid personal injury,
keep the hood closed until there
is no steam. Escaping steam or
coolant is a sign of very high
pressure.
If your engine stalls while
driving

4RUNNER (1998)
Stop the vehicle on a level firm
ground, firmly set the parking
brake and put the transmission
in ºPº (automatic) or reverse
(manual). Block the wheel diag-
onally opposite to the one be-
ing changed if necessary.
Make sure to set the jack prop-
erly in the jack point. Raising
the vehicle with jack improperly
positioned will damage the ve-
hicle or may allow the vehicle
to fall off the jack and cause
personal injury.
Never get under the vehicle
when the vehicle is supported
by the jack alone.
Use the jack only for lifting
your vehicle during wheel
changing.
Do not raise the vehicle with
someone in the vehicle.
When raising the vehicle, do
not put an object on or under
the jack.
Raise the vehicle only high
enough to remove and change
the tire.NOTICE
Do not continue driving with a
deflated tire. Driving even a shortdistance can damage a tire be-yond repair.
ÐRequired tools and spare
tire

4RUNNER (1998)
Only when you cannot receive a
towing service from a Toyota dealer
or commercial tow truck service,
tow your vehicle carefully in accor-
dance with the instructions given in
ºÐEmergency towingº in this Part.
Proper equipment will help ensure that
your vehicle is not damaged while be-
ing towed. Commercial operators are
generally aware of the state/provincial
and local laws pertaining to towing.
Your vehicle can be damaged if it is
towed incorrectly. Although most oper-
ators know the correct procedure, it is
possible to make a mistake. To avoid
damage to your vehicle, make sure
the following few precautions are ob-
served. If necessary, show this page
to the tow truck driver. TOWING PRECAUTIONS:
Use a safety chain system for all tow-
ing, and abide by the state/provincial
and local laws. The wheels and axle
on the ground must be in good condi-
tion. If they are damaged, use a tow-
ing dolly.
Two- wheel drive modelsÐ
(a) Towing with wheel lift type
truck
From frontÐ Manual transmission:
We recommend using a towing dolly
under the rear wheels. If you do not
use a towing dolly, release the park-
ing brake and put the transmission
in neutral.
Automatic transmission:
Use a towing dolly under the rear
wheels.
NOTICE
Never tow a vehicle with an auto-
matic transmission from the frontwith the rear wheels on theground, as this may cause serious
damage to the transmission.
From rearÐ Place the ignition key in
the ºACCº position.
NOTICE
When lifting wheels, take care
to ensure adequate groundclearance for towing at the op-posite end of the raised vehicle.
Otherwise, the bumper and/orunderbody of the towed vehiclewill be damaged during towing.
Do not tow with the key re-moved or in the ºLOCKº posi-tion, as the steering lock mech-
anism is not strong enough tohold the front wheels straight
while towing.
(b) Using flat bed truck