1998 SSANGYONG MUSSO ignition

1F1-26 M162 ENGINE CONTROLS
IDLING CONTROL AND ELECTRONIC PEDAL SYSTEM TEST
Þ 2.1· Ignition:ON
50 512.25 - 2.75 V· ·· ·
· Pedal valve
sensor:
- Power
supply

(potentiometer 2)
· Cable
· ECU
Failure
codeItem
Þ 1.0
Checking method
· Ignition:ON
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with kick
down
Test
stepRequirement
Specified
valuePossible cause
31 47
0.3 - 0.7 V
· ·· ·
· Pedal valve
sensor:
- Signal

(potentiometer 1)
160,
161,
164,
167,
4.3 - 4.8 V
· Þ 1.1
· Cable
· Pedal valve sensor
Þ 1.1
· Ignition:ON
31 324.75 - 5.25 V· ·· ·
· Pedal valve
sensor:
- Power
supply

(potentiometer 1)
· Cable
· ECU
Þ 2.0
· Ignition:ON
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with kick
down 50 48
0.1 - 0.4 V
· ·· ·
· Pedal valve
sensor:
- Signal

(potentiometer 2)
162,
163,
164,
167,
2.1 - 2.5 V· Þ 2.1
· Cable
· Pedal valve sensor
Þ 3.0
· Engine:in idling
84 87
0.3 - 0.9 V· ·· ·
· Throttle
valve
actuator:
- Signal
Throttle valve
potentiometer 1104,
105,
108,
109,
116,
119,
185,
4.0 - 4.6 V· Þ 3.1
· Cable
· E-GAS actuator
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with kick
down

M162 ENGINE CONTROLS 1F1-27
Failure
codeItem
Checking method Test
stepRequirementSpecified
valuePossible cause
Þ 3.1· Ignition:ON
84 1124.75 - 5.25 V· ·· ·
· Throttle
valve
actuator:
- Power
supply(5V)· Cable
· ECU
Þ 4.0
· Ignition:ON
68 670.8 - 2.3 V
The value will
be changed in
1.0 - 2.5V.· ·· ·
· Throttle
valve
actuator:
- Signal
Throttle valve
actuator
motor voltage
supply104,
105,
108,
109,
116,
119,
185,· ECU
· Cable
· E-GAS actuator
· Engine:in idling
- Coolant
temperature:
>70 °C 84 85
4.0 - 4.6 V Throttle valve
potentiometer 2
0.3 - 0.9 V
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with
kick down
Throttle valve
potentiometer
1+2
· Ignition:OFF
< 10 W
Throttle valve
actuator
motor
resistance68 67

M162 ENGINE CONTROLS 1F1-29
FUEL PRESSURE AND INTERNAL LEAKAGE TEST
01 Pressure Tester
02 Pressure Hose
03 Measuring Beaker
Preparation
Connection of the Equipment
1. Turn the ignition switch to "OFF" position.
2. Remove the air cleaner cross pipe.
3. Remove the cap on fuel pressure test plug and connect the
pressure hose and pressure tester.
4. Prepare the beaker for measuring the amount of fuel.
Tools Required
103 589 00 21 00 Pressure Tester
119 589 04 63 00 Pressure Hose

M162 ENGINE CONTROLS 1F1-31
FUEL PUMP TEST
Preparation
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Stop Watch
5 Measuring Beaker
Connection of the Equipment
1. Turn the ignition switch to "OFF" position.
2. Connect the test box to the ECU.0 3 Test Box
04 ECU Test Cable
Tools Required
103 589 00 21 00 Pressure Tester
210 589 00 99 00 Adaptor Line
129 589 00 21 00 Test Box
210 589 08 63 00 Ecu Test Cable

1F1-32 M162 ENGINE CONTROLS
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
1 liter of fuel
supply for
max. 35
seconds· ·· ·
· Fuel pump:
- Fuel supply
ratio· Ignition:ON
- Disconnect the fuel
return pipe and
connect the host to
beaker to collect the
supplied fuel Þ 1.0· Þ 2.0
· Check the fuel line
5 - 9 A
· ·· ·
· Fuel pump:
- Current
consumption· Ignition:ON
- Remove the fuel
relay from the fuse
and relay box in
luggage
compartment and
connect the
amperemeter
between No.1 and
No.3 in relay
box(fuel pump relay
removed position)
for measuring
current consumption Þ 2.0· Fuel pump
533
Multi tester(DC current)
31

1F1-34 M162 ENGINE CONTROLS
Figure 9. Shop Made Cable Figure 10. Fuel Injector Normal Spary Pattern
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
There should
be no leaks
and later
drops from
the injector· ·· ·
· Injector:
- Leakage test· Ignition:ON
- Remove the fuel
distributor and fuel
injector with a unit. Þ 1.0
The spray
pattern of the
injector most
show in the
figure 10.
· Ignition:ON
- Connect the shop
made cable to the
injector
- Collect the spraying
fuel with a beaker
- Connect the shop
made cable to
No.21(+) and No.3
(-) terminal in test
box Þ 2.0· Injector
533
· ·· ·
· Injector:
- Function test
and spray
pattern
check
533

1F1-36 M162 ENGINE CONTROLS
Location
Engine ECU is located at the inside of cowl side trim in right
bottom of instrument panel of passenger side.
Removal & Installation Procedure
1. Turn the ignition switch to "OFF" position.
2. Disconnect the battery negative cable
3. Remove the cowl side trim form passenger side.
4. Unscrew four securing nuts for ECU from mounting bracket.
Installation Notice
5. Pulling out the ECU from bracket.
6. Disconnect the vehicle side coupling(B).
7. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm

M162 ENGINE CONTROLS 1F1-39
Engine Connector
Pin No.Abbreciation
Decription
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80EV5
EV6
EV1
EV4
EV2
EV3
M+
M-
TM.31
ZSC16
ZSA25
ZSB34
NWS
-
-
-
-
MT
GND
LT Injector-cylinder 2
Injector-cylinder 4
Injector-cylinder 1
Injector-cylinder 6
Injector-cylinder 5
Injector-cylinder 3
E-GAS motor plus
E-GAS motor minus
Power ground TM.31
Ignition coil cylinder 1+6
Ignition coil cylinder 2+5
Ignition coil cylinder 3+4
Camshaft control
-
-
-
-
Engine coolant temperature
Temperature ground
Intake air temperature