1998 SSANGYONG MUSSO ignition

SECTION 1D3
OM600 ENGINE COOLING
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1D3-1
General Specifications . . . . . . . . . . . . . . . . . 1D3-1
Fastener Tightening Specifications . . . . . . . . 1D3-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1D3-2
Cooling Circulation . . . . . . . . . . . . . . . . . . . . 1D3-2
Thermostat Operation . . . . . . . . . . . . . . . . . 1D3-3
Cooling System Leakage Test . . . . . . . . . . . 1D3-4
Maintenance and Repair . . . . . . . . . . . . . . 1D3-5On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1D3-5
Drain and Filling of Coolant . . . . . . . . . . . . . 1D3-5
Coolant Pump . . . . . . . . . . . . . . . . . . . . . . . . 1D3-6
Coolant Pump Housing . . . . . . . . . . . . . . . . . 1D3-8
Cooling Fan Clutch . . . . . . . . . . . . . . . . . . . 1D3-10
Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1D3-12
Cooling Sub-System . . . . . . . . . . . . . . . . . . 1D3-14
Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . 1D3-16
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Application
Coolant
Mixing Ratio (Water : anticorrosion)
CapacityDescription
ALUTEC P- 78
50 : 50
10.5L - 11L
9.5L - 10L
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Coolant Pump Bolt
Belt Pulley Bolt
Coolant Pump Housing Return Pipe Bolt
Thermostat Bolt
Cooling Fan Clutch Socket Bolt (Center)
Cooling Fan Clutch Socket Bolt (Side)
Radiator Bolt
Coolant Sub-tank BoltN
· ·· ·
·m
10
10
10
10
45
10
3 - 7
3 - 7
FASTENER TIGHTENING SPECIFICATIONS
662LA
661LA

SECTION 1E1
M162 ENGINE ELECTRICAL
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1E1-1
Alternator Specifications . . . . . . . . . . . . . . . . 1E1-1
Starting Motor Specifications . . . . . . . . . . . . 1E1-2
Battery Specifications . . . . . . . . . . . . . . . . . . 1E1-2
Fastener Tightening Specifications . . . . . . . . 1E1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1E1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1E1-3
Maintenance and Repair . . . . . . . . . . . . . . 1E1-4
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1E1-4
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-4
Starting Motor . . . . . . . . . . . . . . . . . . . . . . . . 1E1-5
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-6
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-7
Ignition Cable . . . . . . . . . . . . . . . . . . . . . . . . 1E1-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 1E1-12
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-12
SPECIFICATIONS
ALTERNATOR SPECIFICATIONS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Application
Output Voltage
Current
Resistance Between Rotor Core and Slip RingDescription
12 - 14 V
115 A
¥ W

1E1-2 M162 ENGINE ELECTRICAL
N·m
14 - 18
4 - 5
45 - 50
12 - 15
6 - 7
35 - 48
12 - 18
12 - 18
12 - 18
9 - 11
9 - 11
25 - 30
STARTING MOTOR SPECIFICATIONS
Application
Voltage
Output PowerDescription
12 V
1.7 KW
BATTERY SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Capacity
Specific Gravity
Max. Tolerance Between CellsDescription
75 AH
³ 1.24
³ 0.04
Application
Alternator Terminal B+Nut
Alternator Terminal D+Nut
Alternator Combinction Bolt
Battery Cable Nut on Starting Motor
Electric Wire Nut on Starting Motor
Starting Motor Mounting Nut
Battery Mounting Bracket Nut
Battery Negative Cable
Battery Positive Cable
Ignition Cable Cover Bolt
Ignition Cable Bolt
Spark plug

M162 ENGINE ELECTRICAL 1E1-7
1 Ignition Coil Cable Cover
2 Bolt (M6 X 60, 7 pieces)......................... 9-11 Nm
3 Spark Plug
SPARK PLUG
Preceding Work : Removal of intake air duct
T1/1Ignition Coil : Cylinder 2 and 5
T1/2Ignition Coil : Cylinder 3 and 4
T1/3Ignition Coil : Cylinder 1 and 6

1E1-8 M162 ENGINE ELECTRICAL
Tools Required
120 589 09 00 Spark Plug Wrench
Replacement Procedure
1. Remove the seven bolts (2) and remove the ignition cable
cover.
Installation Notice
Tightening Torque 9 - 11 Nm
Tightening Torque 9 - 11 Nm
Tightening Torque 9 - 11 Nm
2. Remove the two bolts (M6 X 25) from each ignition cable
and remove the ignition cable.
Installation Notice
3. Remove the spark plug using the special tool.
Installation Notice
Spark Plug Wrench 120 589 02 09 00

M162 ENGINE ELECTRICAL 1E1-9
IGNITION CABLE
Preceding Work : Removal of intake air duct
1 Control Cable Connection
2 Ignition Cable
3 Spark Plug Connector
4 Coupling Plug5a, 5b Secondary Voltage Connection
E Iron Core
L1 Secondary Ignition Coil
L2 Primary Ignition Coil

1E1-10 M162 ENGINE ELECTRICAL
Functions
1. Firing order : 1-5-3-6-2-4
2. The ignition cables are located on the cylinder head cover.
Each ignition coil provides the high voltage to two spark
plugs simultaneously.
- T1/1 : cylinder 2 and 5
- T1/2 : cylinder 3 and 4
- T1/3 : cylinder 1 and 6
Removal & Installation Procedure
1. Disconnect the negative battery cable (1).
2. Remove the ignition cable connector from the ignition cable.
3. Disconnect the secondary spark plug connectors from the
each spark plugs and remove the ignition cable.
Installation Notice 3. The secondary output voltage (5a) is supplied to the No.2
cylinder spark plug through the spark plug connector. The
secondary output voltage (5b) is supplied to the No.5 cylinder
spark plug through the ignition cable. The guide pin (W)
acts as a ground while the ignition cable is operated.
lMake sure that the ignition cables are correctly routed.
lExactly install the ignition cable guide pin into the vehicle
to be grounded.
4. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm

M162 ENGINE ELECTRICAL 1E1-11
Circuit Diagram
Inspection & Maintenance Procedure (for MSE)
1. While the ignition switch is in 'OFF' position, remove the
wiring connectors (1 and 15) from ignition coil and measure
the primary resistance between terminal No.1 and No.15.
2. During engine cranking, measure primary voltage (T1/1)
between ECU terminal No. 71 and No. 69. Notice
If out of specified value, replace the ignition coil.
Specified Value 0.9 - 1.6 W (20°C)
Specified Value 200 - 350 V
Notice
lMeasure remaining cables.
- T1/2 : No. 72 and 69.
- T1/3 : No. 70 and 69.
lIf out of specified value, check ignition cable and ECU.
3. Using a multi-tester, measure the secondary coil resistance
between 5a and 5b.
Specified Value 6 - 8.5 kW