1998 SSANGYONG MUSSO ignition

1F1-68 M162 ENGINE CONTROLS
Camshaft Position Sensor Power Supply
Inspection
1. Turn the ignition switch to 'ON' position.
2. Disconnect the camshaft position sensor connector.
3. Measure the voltage between the No.1 and No.3 pin of
camshaft position sensor while the ignition switch is in "ON"
position.
Notice
If the measured value is not within the specified value, check
the cable.Notice
The signal voltage will be changed in the range of 1.2 -
1.7V.
Camshaft Position Sensor Output Wave
Inspection
1. Connect the test box to the ECU.
2. Measure the output wave between the ECU terminal No.104
and No.106 using the scanner or the oscilloscope while the
engine speed is at idle.
Notice
Replace the camshaft position sensor if cannot get the
output wave as shown in the figure.
Specified Value 11 - 14 V
Specified Value 1.2 - 1.7 V
Camshaft Position Sensor Signal Voltage
Inspection
1. Connect the test box to the ECU.
2. Measure the voltage between the ECU terminal No.11 and
No.106 while the engine speed is at idle.

M162 ENGINE CONTROLS 1F1-73
Oxygen Sensor Signal Voltage Inspection
1. Measure the oxygen sensor signal voltage between the ECU
terminal No.11 and No.9. Maintain the engine speed ia at
idle while the coolant temperature is over 80°C.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Voltage Inspection
1. Measure the oxygen sensor heating voltage between the
ECU terminal No.11 and No.9. Maintain the engine speed ia
at idle while the coolant temperature is over 80°C.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Current Consumption
Inspection
1. Measure the oxygen sensor heating current consumption
between the ECU terminal No.9 and No.5 while the ignition
switch is in "ON" position.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Specified Value 0.2 - 2.0 A
Specified Value -0.2 - 1.0 V
Specified Value 11 - 14

1F1-76 M162 ENGINE CONTROLS
2. Measure the resistance between the coolant temperature
sensor terminal No.1 and No.4 with the coolant temperature
sensor disconnected.
Inspection
1. Measure the coolant sensor input voltage between the ECU
terminal No.79 and No.78 while the ignition switch in "ON"
position.
Notice
Replace wiring and coolant temperature sensor if out of
specified value.
allowable error :±5%
allowable error :±5%
Voltage (V)
3.57
1.22
0.78
Temperature (°C)
20
30
40
Resistance (W)
2,500
322
185
Temperature (°C)
20
30
40

SECTION 1F2
M161 ENGINE CONTROLS
TABLE OF CONTENTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F2-2
Fastener Tightening Specifications . . . . . . . . 1F2-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F2-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F2-3
Schematic and Routing Diagrams . . . . . . . 1F2-4
E23 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F2-4
E23 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F2-5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-6
Self Diagnosis Socket Pin Numbers and
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F2-6
Self Diagnosis Failure Code (for E23 ENG) . 1F2-7
Test Box Connection . . . . . . . . . . . . . . . . . . 1F2-10
Fuel Injection System Test . . . . . . . . . . . . . 1F2-11
Ignition System Test . . . . . . . . . . . . . . . . . . 1F2-20
Idling Control and Electronic Pedal
System Test . . . . . . . . . . . . . . . . . . . . . . . 1F2-25
Air Conditioner Control System Test . . . . . . 1F2-27
Fuel Pressure and Internal Leakage Test . . 1F2-28
Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F2-30Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F2-32
Maintenance and Repair . . . . . . . . . . . . . 1F2-34
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F2-34
ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-34
Fuel Pressure Regulator . . . . . . . . . . . . . . 1F2-45
Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F2-49
Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-54
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-57
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-58
Purge Switchover Valve . . . . . . . . . . . . . . . 1F2-62
Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F2-64
Crankshaft Position Sensor . . . . . . . . . . . . 1F2-66
Camshaft Position Sensor . . . . . . . . . . . . . 1F2-68
Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F2-70
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F2-73
Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F2-75
Coolant Temperature Sensor . . . . . . . . . . . 1F2-76
Accelerator Pedal Module . . . . . . . . . . . . . . 1F2-79

1F2-6 M161 ENGINE CONTROLS
DIAGNOSIS
SELF DIAGNOSIS SOCKET PIN NUMBERS AND DESCRIPTIONS
1 Ground
2 Ignition 1
3 Battery Power Supply (Fuse NO.17)
4 REKES :PIN 6
5 Engine Speed Signal :MSE PIN 60
6 TCCU(Part-time)
7 STICS(PIN 26)
8-
9-
10 Air Bag(PIN 20)
11 Remote Engine Start Unit(PIN 10)12 -
13 Brake System
(ABS 5.3:PIN 11, ABS/ABD 5.3:PIN 46)
14 MSE 3.62S/3.53S(ECU Data Output:PIN 58)
15 TOD(PIN 20)
1 6 Immobilizer
17 -
1 8 TCU(PIN 23)
19 -
2 0 K-LINE(ECS:PIN 23)

M161 ENGINE CONTROLS 1F2-7
No ignition voltage output(NO.1 ignition coil;
1, 4cylinder)
No ignition voltage output(NO.2 ignition coil;
2, 3cylinder)
Cranshaft position sensor adaption failure
Start signal recognition failure
No.1 injector short(PWR)
No.1 injector open/short(GND)
No.2 injector short(PWR)
No.2 injector open/short(GND)
No.3 injector short(PWR)
No.3 injector open/short(GND)
No.4 injector short(PWR)
No.4 injector open/short(GND)
High oxygen sensor voltage
Low oxygen sensor amplifying voltage
Oxygen sensor operating failure
Not excessive lean indication in oxygen
sensor(during coasting)
Oxygen sensor heater short(power)
Oxygen sensor heater open/short(GND)
Low oxygen sensor voltage
Short learning control failure
Lambda control failure (rich stop)
Lambda control failure (lean stop)
Lambda idle adaptation failure(above rich
threshold)
Lambda idle adaptation failure(below lean
threshold)
learning control failure(rich, low load) Coolant temperature sensor open
Coolant temperature sensor short
Coolant temperature sensor signal failure
Intake temperature sensor open
Intake temperature sensor short
Intake temperature sensor signal failure
Low battery voltage
HFM sensor signal failure
HFM sensor signal failure (Low)
HFM sensor signal failure (High)
Crankshaft position sensor signal failure
(no engine revolution signal)
Crankshaft position sensor signal failure
(rpm > max. value)
No.1 cylinder recognition failure
Crankshaft position sensor signal failure
(gab recognition failure)
Transmission coding failure
Transponder signal communication failure
CAN communication failure : TCU(A/T only)
CAN communication failure :
communication initialization failure
Fuel pump relay short(PWR)
Fuel pump relay open/short(GND)
Purge valve short
Purge valve open/short
Condenser fan(HI) relay short(PWR)
Condenser fan(HI) relay short(GND)
No.1 knock sensor signal failure
No.1 cylinder synchronization failure 00
01
02
03
04
05
08
09
10
11
17
18
19
20
21
25
26
31
34
35
40
41
44
45
56
58
Failure
codeDescriptionFailure
codeDescription
64
65
67
71
72
73
74
75
76
77
78
79
80
81
82
83
86
87
89
93
96
97
98
99
100
SELF DIAGNOSIS FAILURE CODE (FOR E23 ENG)

M161 ENGINE CONTROLS 1F2-11
FUEL INJECTION SYSTEM TEST
Failure
codeItem
Þ 1.0
Checking method
· Ignition:ON
Test
stepRequirementSpecified
valuePossible cause
10 1211 -14V
· ·· ·
· ECU:power
supply
- terminal 30
(TM.30)
Þ 2.2· ·· ·
· Power
supply:
- terminal 87
(TM.87)· Ignition:ON· Power supply cable
· OVPR 08,
·Þ 1.1
·Þ 1.2
Þ 1.1
· Ignition:ON
10 211 -14V· ·· ·
· Ground
cable:
- Battery
ground· Ground cable
· Ground conditionDiagnosis
socket
69 2
Diagnosis
socket
Þ 1.2· Ignition:ON
11211 -14V· ·· ·
· Power
supply:
- terminal 30
(TM.30)· Power supply cable
Diagnosis
socket
Þ 2.0· Ignition:ON
51111 -14V· ·· ·
· ECU:power
supply
- terminal 87
(TM.87)08,·Þ 1.1
·Þ 2.1
Þ 2.1
· Ignition:ON 11 -14V· ·· ·
· Ground
cable
- Electronic
ground· Ground cable
52
Diagnosis
socket
111
Diagnosis
socket· Ignition:OFF
11 -14V
< 1V
Þ 3.0
· Engine:in Cranking
52· Cable
· Ignition Swith 11 -14
(during engine
cranking)
· ·· ·
· Start signal:
- terminal 50
(TM.50)

1F2-12 M161 ENGINE CONTROLS
Failure
codeItem
09,
10,
11,
Checking method Te s t
stepRequirementSpecified
valuePossible cause
Þ 4.0· ·· ·
· HFM sensor
signal
105 81· Ignition:ON0.9 - 1.1V· Þ 4.1 - 4.3
· Cable
· External air inflow
· HFM sensor
· Engine:in Idle
(Coolant temperature
: > 70°C )1.3 - 1.7V
Þ 4.1
105 4
· Ignition:ON
· HFM sensor
connector removed4.7 - 5.2V
· Cable
· ECU coupling
· ·· ·
· HFM sensor:
- 5V power
supplyHFM
sensor
Þ 4.2
3 108· Ignition:ON
· HFM sensor
connector removed4.7 - 5.2V
· Þ 4.3
· Cable
· ·· ·
· HFM sensor:
- 5V power
supplyHFM
sensor
Þ 4.3
104 2· Ignition:ON
· HFM sensor
connector removed11 - 14V
· Cable
· OVPR
· ·· ·
· HFM sensor:
- 12V power
supplyHFM
sensor
03,
04,
05,Þ 5.0· ·· ·
· Intake air
temperature
sensor:
- Voltage105 80· Ignition:ON· Þ 5.1
· ECU
Þ 5.1· Ignition:OFF
· No.2 ECU coupling
removed 105 80
· Cable
· HFM sensor
· ·· ·
· Intake air
temperature
sensor:
- Resistance
: voltage value
is increased
when engine
rpm is
increased
± 5%
°C
10
20
30
40
50
60
± 5%W
3600
2420
1662
1166
853
600 °C
10
20
30
40
50
60V
3.1
2.65
2.18
1.76
1.4
1.1