1998 SSANGYONG MUSSO ignition

M161 ENGINE CONTROLS 1F2-35
Location
Engine ECU is located at the inside of cowl side trim in right
bottom of instrument panel of passenger side.
Removal & Installation Procedure
1. Turn the ignition switch to "OFF" position.
2. Disconnect the battery negative cable
3. Remove the cowl side trim form passenger side.
4. Unscrew four securing nuts for ECU from mounting bracket.
Installation Notice
5. Pulling out the ECU from bracket.
6. Disconnect the vehicle side coupling(B).
7. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm

1F2-38 M161 ENGINE CONTROLS
Engine Connector
Pin No.Abbreviation
Description
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80-
-
EV1
EV4
EV2
EV3
M+
M-
TM.31
-
ZSB23
ZSA14
NWS
EGR
-
SLP
-
MT
GND
LT -
-
Injector-cylinder 1
Injector-cylinder 2
Injector-cylinder 3
Injector-cylinder 4
E-GAS motor plus
E-GAS motor minus
Power ground TM.31
-
Ignition coil cylinder 2+3
Ignition coil cylinder 1+4
Camshaft control
EGR (Exhaust Gas Recirculation)
-
Second air pump relay
-
Engine coolant temperature
Intake air temperature ground
Intake air temperature

1F2-42 M161 ENGINE CONTROLS
Pin No.
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Abbreviation Description
-
-
Injector-cylinder 1
Injector-cylinder 2
Injector-cylinder 3
Injector-cylinder 4
E-GAS motor plus
E-GAS motor minus
Power ground TM.31
-
Ignition coil cylinder 2+3
Ignition coil cylinder 1+4
Camshaft control
-
Second air pump relay
-
Engine coolant temperature
Temperature ground
Intake air temperature
Hot film air mass signal
-
-
E-GAS potentiometer ground
E-GAS potentiometer 2 signal
-
E-GAS potentiometer 1 signal
-
-
-
-
-
EV1
EV4
EV2
EV3
M+
M-
TM.31
-
ZSB23
ZSA14
NWS
-
-
SLP
-
MT
GND
LT
HFM
-
-
-
IP2S
-
IP1S
-
-
--
-
l
l
l
l
l
l
l
-
l
l
l
-
-
¡
-
l
l
l
l
-
-
l
l
-
l
-
-
-
-
-
l
l
l
l
l
l
l
-
l
l
l
-
-
¡
-
l
l
l
l
-
-
l
l
-
l
-
-
-
E23 ENG,
4speed A/T E23 ENG,
5speed A/T

1F2-44 M161 ENGINE CONTROLS
Removal & Installation Procedure
· ·· ·
·When removing the ECU only
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Unscrew the left and right bolt (3) on bolt (1) and auxiliarly
bracket and remove the auxiliarly bracket from the bracket
assembly (2).
Installation Notice
5. Unscrew the four bolts (5) and disconnect the ECU (6) from
the bracket assenbly.
Installation Notice
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque6 - 8 Nm
5 - 7 Nm(1)
(3)
Tightening Torque 5 - 7 Nm
8. Unscrew the bolts (5) and disconnect the ECU (6) from the
bracket assenbly.
Installation Notice · ·· ·
·When Removing the ECU with ABS or ABS/ASR Unit
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Disconnect the coupling from ABS or ABS/ASR unit.
5. Unscrew the bolt (1) and the left and right flange nuts.
6. Remove the ECU with ABS or ABS/ASR unit assembly.
7. Unscrew the left and right bolt (3) on the auxiliary bracket
and remove the auxiliary bracket from the bracket assembly.
Installation Notice
Tightening Torque 6 - 8 Nm
Tightening Torque 5 - 7 Nm
Tightening Torque 5 - 7 Nm
9. Installation should follow the removal procedure in the
reverse order.

1F2-50 M161 ENGINE CONTROLS
Tightening Torque
22.5 - 27.5 Nm
Tightening Torque22.5 - 27.5 Nm
Removal & Installation Procedure
1. Discharge the fuel pressure from the fuel pressure test
connector by pushing service valve (arrow).
2. Disconnect the battery ground cable.
3. Disconnect the vacuum hose from the fuel pressure
regulator.
4. Disconnect the cable from ignition coil.
5. Remove the fuel return and supply line.
Installation Notice
Notice
lFor removal, cover around parts with cloths not to
bestained by fuel.
lIn case of checking the injector only, do not remove the
fuel return and supply line.
6. Remove the four injector connectors (arrows).
7. Unscrew the two combination bolts (8).
Installation Notice

M161 ENGINE CONTROLS 1F2-51
9. Installation should follow the removal procedure in the
reverse order.
10. Check for fuel pressure and internal leakage by operating
the engine. 8. Pull out the injector from intake manifold and remove the
fuel distributor.
Notice
Replace the injector O-ring with new one.
Ignition Coil & Cable
lIgnition coil T1/1 No.1 cylinder + No.4 cylinder
lInition coil T1/2 No.1 cylinder + No.4 cylinder

1F2-52 M161 ENGINE CONTROLS
Fuel Pressure Test
1. Turn the ignition switch to "OFF" position.
2. Remove the fuel pressure test connector.
Vacuum Hose Connected (bar) 3.2-3.6
Vacuum Hose Disconnected (bar) 3.7-4.2
5. Replace the pressure regulator diaphragm if out of the
specification. 3. Connect the fuel pressure gauge to the fuel pressure test
connector.
4. Test the fuel pressure at idling by operating the engine.

M161 ENGINE CONTROLS 1F2-55
Removal & Installation Procedure
1. Remove the O-ring.
Check for damage and replace it if necessary.
2. Remove the injector bracket from the injector.
Installation Notice
Exactly seat the anti-twist lock into the square groove in
injector.
3. Separate the injector from the fuel distributor.
Inspection & Maintenance
Inspection of the Injector operation and spray pattern
1. Connect the contact box to the ECU.
2. Connect the shop made test plug to the injector and place
it into the tank.
3. Position the ignition switch to ON.
4. Connect the pin 63(+) and 69(-) of the contact box with a
test cable.
5. Check the injector spray pattern.
Notice
Replace the injector if the injector spray pattern is abnormal
or the fuel doesn't inject.
Injector Resistance Inspection
1. Remove the injector connector.
2. Measure the injector coil resistance using a resistance
tester.
Notice
Replace the injector if the measured values is out of the
specified values. Check the connector and wire connection
between the ECU and the injector if the measured values
are normal.
Specified Value
14 - 17 W