1998 SSANGYONG MUSSO belt

1B1-42 M162 ENGINE MECHANICAL
1 Center Bolt (M18 x 50)......1st step 200- 220 Nm
2nd step 90°+10°
2 Vibration Damper Disk
3 Bolt (M6 x 20, 6 pieces).....................7.7-9.5 Nm
BELT PULLEY AND VIBRATION DAMPER
Preceding Work : Removal of cooling fan and viscous clutch
Removal of fan shroud
Removal of drive belt
4 Vibration Damper Assembly
5 Woodruff Key
6 Bolt (M6 x 12, 4 pieces)......................... 9-11 Nm
7 Cooling Fan Pulley

M162 ENGINE MECHANICAL 1B1-45
CRANKSHAFT FRONT RADIAL SEAL
Preceding Work : Removal of belt pulley and vibration damper
1 Center Bolt (M18 x 50)
................................ 1st step 200-220 Nm
2nd step 90° +10°
2 Center Bolt Washer
3 Sleeve (Special Tool)
4 Crankshaft Front Seal
5 Key
Tools Required
601 589 03 14 00 Sleeve
Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice
Use a clean cloth not to damage the radial seal mounting
hole and the crankshaft.
5. Remove the sleeve and install the belt pulley and the
vibration damper.
6. Check for leaks while operating the engine. 2. Coat the radial sealing lip with engine oil.
3. Using the sleeve, assemble the radial seal .
4. Align the sleeve groove and the woodruff key and tighten
the center bolt until the center bolt and the damper disk
stop in the movement.
Installation Notice
Tightening Torque1st step 200 - 220Nm
2nd step 90° + 10°

SECTION 1B2
M161 ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1B2-2
Fastener Tightening Specifications . . . . . . . . 1B2-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1B2-4
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1B2-4
Maintenance and Repair . . . . . . . . . . . . . . 1B2-9
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1B2-9
Engine Assembly . . . . . . . . . . . . . . . . . . . . . 1B2-9
Crankcase Ventilation System . . . . . . . . . . 1B2-17
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-21
Power Steering Pump and A/C Bracket . . . 1B2-22
Hydraulic Engine Mounting Insulator . . . . . . 1B2-25
Poly V-Belt . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-28
Tensioning Deivce . . . . . . . . . . . . . . . . . . . . 1B2-30
Tensioning Device Shock Absorber . . . . . . 1B2-31
Poly V-Belt Inspection . . . . . . . . . . . . . . . . . 1B2-32
Cylinder Head Cover . . . . . . . . . . . . . . . . . 1B2-35
Cylinder Head Front Cover . . . . . . . . . . . . . 1B2-37
Cylinder Head . . . . . . . . . . . . . . . . . . . . . . . 1B2-39
Timing Gear Case Cover . . . . . . . . . . . . . . 1B2-44
Crankshaft Sealing Rear Cover . . . . . . . . . 1B2-47
Belt Pulley and Vibration Damper . . . . . . . . 1B2-49
Crankshaft Front Radial Seal . . . . . . . . . . . 1B2-52
Crankshaft Rear Radial Seal . . . . . . . . . . . 1B2-53
Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-54
Flywheel/Driven Plate . . . . . . . . . . . . . . . . . 1B2-60
Camshaft Adjuster . . . . . . . . . . . . . . . . . . . 1B2-62
TABLE OF CONTENTS
Camshaft Sprocket Bolt . . . . . . . . . . . . . . . 1B2-65
Camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-66
Camshaft Timing Position . . . . . . . . . . . . . . 1B2-69
Valve Spring . . . . . . . . . . . . . . . . . . . . . . . . 1B2-72
Valve Stem Seal . . . . . . . . . . . . . . . . . . . . . 1B2-76
Chain Tensioner . . . . . . . . . . . . . . . . . . . . . 1B2-77
Timing Chain . . . . . . . . . . . . . . . . . . . . . . . . 1B2-80
Tensioning Rail . . . . . . . . . . . . . . . . . . . . . . 1B2-85
Cylinder Head Guide Rail . . . . . . . . . . . . . . 1B2-86
Crankcase Guide Rail . . . . . . . . . . . . . . . . . 1B2-87
Crankshaft Sprocket . . . . . . . . . . . . . . . . . . 1B2-88
Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-90
Connecting Rod . . . . . . . . . . . . . . . . . . . . . 1B2-93
Piston Ring . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-95
Oil Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-97
Engine Oil and Oil Filter Element . . . . . . . . 1B2-99
Oil Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1B2-101
Oil Pressure Relief Valve . . . . . . . . . . . . . 1B2-103
Oil Non-Return Valve . . . . . . . . . . . . . . . . 1B2-104
Oil Dipstick Guide Tube . . . . . . . . . . . . . . 1B2-105
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . 1B2-106
Core Plugs in Crankcase . . . . . . . . . . . . . 1B2-106
Cylinder Bore . . . . . . . . . . . . . . . . . . . . . . 1B2-108
Crankcase Mating Surface . . . . . . . . . . . . 1B2-110
Cylinder Head Mating Surface . . . . . . . . . 1B2-112

1B2-2 M161 ENGINE MECHANICAL
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
N
· ·· ·
·m
35 - 40
10 - 15
5 - 10
21 - 25
30
56 - 66
50 - 60
22.5 - 27.5
41.5 - 49.5
22.5 - 27.5
22.5 - 27.5
9 - 11
9 - 11
9 - 11
9 - 11
22.5 - 27.5
10
+90°
55
+90°
+90°
22.5 - 27.5
22.5 - 27.5
9 - 10
9 - 10
200
+90°
40
+90°
45
+90°
35
9 - 11
20
+90°
20
+90°
20 / + 90°
20 / + 90°
22.5 - 27.5Application
Power Steering Hydraulic Lines
A/C High Pressure and Liquid Hose
Radiator Support Menber Bolt
Fuel Supply and Return Hose to Fuel Distributor
Exhaust Manifold and Pipe
Propeller Shaft to Transmission
Engine Mounting Nut
Alternator Carrier Bolt
Belt Pulley Bolt
Steering Pump Bolt
A/C Bracket Bolt
Intake Air Duct Bolt
Ignition Cable Cover Bolt
Cylinder Head Cover Bolt
Camshaft Adjuster Bolt
Cylinder Head Front Cover Bolt
Flange Bolt in Exhaust Camshaft Sprocket
Cylinder Head Bolt
Cooling Fan Bracket Bolt
Timing Gear Case Cover Bolt M8
M6
Crankshaft Rear Cover Bolt
Vibration Damper Center Bolt
Connecting Rod Bearing Cap Bolt
Flywheel Stretch Bolt
Amarture Bolt in Flywheel
Ring and Seal Cover Nut in Flywheel
Sprocket Bolt to Exhaust Camshaft
Camshaft Adjuster Flange Bolt
Intake Flange Shaft Bolt
Exhaust Camshaft Sprocket Bolt
Camshaft Bearing Cap Bolt

M161 ENGINE MECHANICAL 1B2-21
ALTERNATOR
Removal & Installation Procedure
1. Remove the drive belt.
2. Remove the alternator.
3. Unscrew the alternator carrier bolts (1,2,3) and remove the
carrier (4).
Installation Notice
Tightening Torque 22.5 - 27.5 Nm
Notice
Apply 3Nm of torque when mounting the bolt (1); apply 25 ±
2.5Nm of torque when mounting the bolts (2), and (3); and
then tighten the bolt (1) with 25 ± 2.5Nm of torque.
4. Installation should follow the removal procedure in the
reverse order. 1 Bolt (M8 X 40, 3 pieces).................22.5-27.5 Nm
2 Bolt (M8 X 70, 2 pieces).................22.5-27.5 Nm3 Bolt (M8 X 85, 1 piece)...................22.5-27.5 Nm
4 Alternator Bracket

1B2-22 M161 ENGINE MECHANICAL
POWER STEERING PUMP AND A/C BRACKET
Preceding Work : Removal of cooling fan and shroud
Removal of drive belt
1 Nut .................................................35.2-28.8 Nm
2 Washer
3 Belt Pulley
4 Bolt (M8 X 91, 2 pieces).................22.5-27.5 Nm
5 Power Steering Pump
6 Bracket
7 Washer
8 Bolt (M8 X 20, 2 pieces).................22.5-27.5 Nm9 Washer
10 Bolt (M8 X 105,4 pieces)................22.5-27.5 Nm
11 A/C Compressor
12 Bolt (M8 X 50, 5 pieces, M8 X 80,
5 pieces)........................................22.5-27.5 Nm
13 A/C Bracket
14 Vent Hose
15 Bracket Gasket...................................... Replace

M161 ENGINE MECHANICAL 1B2-23
Removal & Installation Procedure
1. Remove the belt pulley after removal of poly v-belt.
Installation Notice
2. Disconnect the hydraulic pipe of the power steering pump
and drain the oil.
3. Unscrew the bolts (arrows) and remove the steering pump.
Installation Notice Notice
Pull the tensioning pulley counterclockwise as shown in the
figure.
4. Remove the compressor after disconnecting the wiring
connector and refrigerant pipe of A/C compressor.
Notice
Discharge all the refrigerant before removing the pipes.
Tightening Torque 40.5 - 49.5 Nm
Tightening Torque 22.5 - 27.5 Nm

1B2-28 M161 ENGINE MECHANICAL
POLY V-BELT
Preceding Work : Removal of cooling fan
1 Poly V-belt (2,155 mm)
2 Belt Tensioning Pulley
Removal & Installation Procedure
1. Release the belt tension by turning the stud on the cap with
12 sided wrench or spanner counterclockwise.
2. Remove the poly v-belt.
Notice
Check the belt for damage and tensioning pulley bearing
point for wear and replace them if necessary.
3. Install the belt after prying the tensioning pulley.
3 Belt Tensioner