1998 SSANGYONG MUSSO lock

SECTION 8A
SEAT BELTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 8A-1
Fastener Tightening Specifications . . . . . . . . . 8A-1
Component Locator . . . . . . . . . . . . . . . . . . . 8A-2
Front Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . 8A-2
Rear Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . 8A-3
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
General Description and System
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 8A-4
Driver Seat Belt Warning . . . . . . . . . . . . . . . . 8A-4
Operation and Functional Checks . . . . . . . . . 8A-4
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Anchor BoltNlm
35 - 55

8A-4 SEAT BELT
GENERAL DESCRIPTION
AND SYSTEM OPERATION
DRIVER SEAT BELT WARNING
The driver's safety belt incorporates a safety belt reminder
light in the instment cluster remind the driver if the safety belt
is not fastened when the ignition is turnd ON.
OPERATION AND FUNCTIONAL
CHECKS
Caution:
lKeep sharp objects and potentially damaging objects
away from the seat belts.
lAvoid bending or damaging any portion of the buckle
or the latch plate.
lDo not bleach or dye the belt webbing. Use only mild
soap and water in order to clean the belts.
lWhen installing the seat belt anchor bolts and the
screws, start the bolts and screws by hand in order
to prevent crossthreading.
lDo not attempt any repairs on the retractor
mechsemblies with new assemblies.
lReplace any belts that are cut r damaged in any way.
1. Inspect all saet belt anchor bolts and the screw in order to
verify that they are secure.
2. Inspect the seat belt buckle. The buckle must lock and
unlock easily.
3. After inserting the latch into the buckle, tug sharply on the
belt. The buckle must remain locked.
4. Fully extend the shoulder belt portion to make sure that
there is no twisting or tears in the belt.
5. Let the shoulder belt retract fully. The belt should retract
easily.

SECTION 8B
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 8B-1
General Specifications . . . . . . . . . . . . . . . . . . 8B-1
Schematic and Routing Diagrams . . . . . . . . 8B-2
Air Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8B-2
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8B-3
Function Description . . . . . . . . . . . . . . . . . . 8B-4
Air Bag Module . . . . . . . . . . . . . . . . . . . . . . . . 8B-6
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 8B-7
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 8B-7
Self Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . 8B-10
Circuit Diagram . . . . . . . . . . . . . . . . . . . . . . . 8B-16
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Air bag System Deployment Time
Detection Time
Operating Temperature
Storage Temperature
Air Bag Replacement Interval
Voltage Range
Current Consumption
Acceleration Range
Max. Acceleration
Voltage Ramp
Energy Reservation
Inflator Ignition Energy
Squib Resistance
Air Bag Warning Lamp ON Time (When Ignition ON)Description
< 20ms
< 5ms
-40°C ~ +85°C
-40°C ~ +90°C
Every 10-year after installation
9-16V
5ms after ignition switch ON < 1A,
5ms ~ 5sec. <300mA, after 5sec. < 100mA
+/-50g
+/-600g pulse
0.5 ~ 2.0 V/s
150ms after battery disconnection
4.3mJ
2.15 ± 0.35 W
6 sec.
Air Bag Diagram . . . . . . . . . . . . . . . . . . . . . . 8B-17
Maintenance and Repair . . . . . . . . . . . . . . 8B-18
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 8B-18
Air Bag Module . . . . . . . . . . . . . . . . . . . . . . . 8B-18
Clock Spring . . . . . . . . . . . . . . . . . . . . . . . . . 8B-19
Air Bag Control Unit (AC4) . . . . . . . . . . . . . . 8B-21
General Description and System
Operation . . . . . . . . . . . . . . . . . . . . . . . . 8B-22
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 8B-22
Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8B-22

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-3
CAUTIONS
Failure to follow the correct service procedure can cause air bag damage or personal injury due to unexpected air
bag deployment. Before service (removal and installation of part, check for replacement), please be weal noticed of
following items for your correct service.
1. For service, turn the ignition switch to ‘LOCK’ position and wait for 30 seconds after disconnecting the negative
battery cable.
2. If the vehicle collapsed, remove the air bag ECU first to reserve the crash records.
3, Never use other vehicles’ air bag components and replace with specified new part.
4. Never disassemble or repair the air bag module, air bag unit and wiring harness to re-use.
5. Replace the air bag module and air bag unit with new if it dropped, cracked or damaged.
6. Only qualified technicians in service shop should check or repair the air bag,
7. Before service, should be well noticed of warning labels on the vehicle.
A. Sun Visor Side
[Warning]
Pull down the sun visor and see SRS air bag
warning lamp on the head lining.
B. Head Lining
[Warning]
1 . This vehicle is equipped with air bag. Air bag is
supplemental device for the seatbelt. Fasten
your seatbelt.
2. This air bag should be replaced by authorized
supplier within replacement intervals.
3. When the ignition key is turned to ON position,
SRS warning lamp will turn on for 6 sec. and go
off. In this case, the system is normal.
For the following cases, see service manual.
- SRS warning lamp does not turn on.
- SRS warning lamp does not go off.
- SRS warning lamp continues to blink.
C. Steering Wheel Body Inner
[Warning]
Before removing the steering wheel, read service
manual first. Set the front wheels straight forward
and align the center position marks of SRS clock
spring. Improper removal or installation of the
steering wheel can damage the SRS components.D. Engine Compartment
[Warning]
This vehicle is equipped with air bag. Before
checking the engine compartment, read service
manual first. Faultuy check and service can cause
SRS air bag deployment and system defects that
can be led to severe damage.
E. Battery Cable
[Warning]
Before disconnecting the battery power, read
service manual first.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-19
Air Bag
Horn (Relay)
Remote Control (Electronic Circuit)
CLOCK SPRING
General Specification
Voltage
Rating Operating Voltage
Current Rating
Air Bag Circuit Resistance
Isolating Resistance
Rotating RangeDC 12V
DC 6 - 18V
10 - 30mA(6A,0.1second)
200 - 220mA
15mA
0.16 - 0.38W(-40°C - 85°C)
5MW
2.7 - 3.1 Rotation from neutral
Position to Both Sides
Notice
lClock spring can not be repaired.
lDo not disassemble or modify.
lTo adjust to the center position, rotate clockwise until it
stops and then rotate it counterclockwise 2.3 ± 0.2
revolutions and align marks. If not, airbag system can
not work normally and driver can be injured seriously.

8B-20 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
Removal & Installation Procedure
preceding work : removal of steering wheel
1. Turn the ignition switch to “OFF” position and disconnect
the battery negative cable. Start the procedure after waiting
over 3oseconds.
2. Unscrew 3 screws from lower cover on steering column shaft
and remove the lower cover.
3. Unscrew 4 screws from clock spring and remove the clock
spring
Installation Notice
lDon’t try to repair and modify the clock spring.
lWhen aligning the neutral position, turn to clockwise until it
stops, and turn to counter clockwise until the marks are
aligned

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-21
AIR BAG CONTROL UNIT(AC4)
Removal & Installation Procedure
AC4 is installed on the center portion of the front floor tunnel.
Built-in accelerometer sensor detects collision and determines
action or non-action and ignition time.
Notice
Do not disassemble the AC4 to repair. If defective, replace it.
AC4 should not be shocked or vibrated by dropping on the
ground or bumping.
Replace the AC4 with new after air bag inflation.
1. Disconnect the negative battery cable and wait for 30
seconds before starting service.
Notice
Though battery cable is disconnected, air bag control unit
will maintain backup power for 150ms and air bag can be
inflated, so wait for min.30 seconds.
2. Remove the console box and center fascia panel assembly.
3. Remove the heater control switch and audio assembly.
4. Remove the lower side panel of the driver’s portion and
glove box.
5. Remove the lower main panel.
6. Release the lock lever of the AC4 connector and disconnect
the connector.
7. Unscrew 3 nuts and remove the AC4.
Notice
For installation, horizontal position should be secured for
the better changes of collision pulse between the vehicle
body and air bag control unit.
8. Installation should follow the removal procedure in the
reverse order.
Inspection Procedure
1. Check AC4 case and welt bolts for crack or deformation.
2. Check connector, lock lever and terminal for deformation.
Notice
Replace the AC4 with new if dust, deformation or corrosion
found.

8B-22 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
GENERAL DESCRIPTION
AND SYSTEM OPERATION
INTRODUCTION
SRS (Supplemental Restraint System) air bag protects driver
and passenger by inflating air bag under collision and seat
belt pre - tensioner is a supplemental equipment for seat belt
reducing shocks from the collision by pulling passenger’s body
against seat back at the same time of air bag inflation.
Air bag unit has diagnosis functions and indicates system
malfunctions to the driver by turning on the air bag warning
lamp.
CAUTION
Perform the service procedures for the air bag system as
ordered, if not, the air bag can be operated suddenly and it
could result in damage of air bag or injury. Before service
(removal, installation, checking and replacement of parts),
observe the following instructions and service correctly.
1. To service, turn the ignition switch to ‘LOCK’ position and
disconnect the negative battery cable and continue the
procedures after approx. 30 seconds.
2. If the vehicle is damaged due to accident, remove the air
bag ECU first to get the accident records.
3. Never use the other vehicle’s air bag parts and replace
with genuine part, if required.
4. Do not disassemble or repair the air bag module, air bag
unit and wiring harness to reuse.
5. Replace the air bag unit or air bag module if dropped,
cracked or damaged.