1998 SSANGYONG MUSSO torque

1B3-60 OM600 ENGINE MECHANICAL
35. Connect the wires to the coolant temperature sensor and
the glow plug sensor.
36. Replace the intake manifold gasket.
37. Install the intake manifold.
Tightening Torque 25 Nm
33. Replace the gasket and install the cylinder head cover.
Tightening Torque 10 Nm
34. Install the blow-by hose.

OM600 ENGINE MECHANICAL 1B3-61
38. Replace the O-ring of heater feed pipe and install it to the
cylinder head.
Notice
For installation, clean the hole.
39. Install the bracket of heater feed pipe to the oil filter.
40. Install the fuel pipe and the accelerator control linkage.
41. Connect the fuel lines to the injection nozzles and to the
injection pump.
Box Wrench Insert 000 589 77 03 00
Tightening Torque 18 Nm

1B3-62 OM600 ENGINE MECHANICAL
43. By inserting a rod into the tensioning lever upper hole and
pulling the rod, install the bolt and then tighten the nut.
44. Install the oil dipstick tube bracket.
Tightening Torque 10 Nm
45. Hold the cooling fan with the counter holder and tighten
the bolt.
42. Install the poly V-belt.
Notice
Be careful not to contaminate the belt.
Tightening Torque 23 Nm

OM600 ENGINE MECHANICAL 1B3-67
Installation Procedure
1. Thoroughly clean the sealing surface and apply sealant.
2. Install the timing case cover.
Notice
Bolts arrangement
1.M6 x 60
2.M6 x 70
3.M6 x 40
3. Tighten the socket bolts in the chain box.
Tightening Torque 10 Nm
Tightening Torque 23 Nm
4. Tighten the oil pan bolts.
Tightening Torque10 Nm
10 Nm
23 Nm
Socket bolt
M6 bolt
M8 bolt

1B3-68 OM600 ENGINE MECHANICAL
Tightening Torque25 Nm 5. Install the flange, vibration damper and crankshaft belt
pulley.
Notice
Replace front radial seal if necessary.
6. Install the alternator bracket.
25 Nm Front
Side
7. Install the alternator
Tightening TorqueUpper - 25 Nm
Low - 25 Nm
8. Install the cylinder head cover.
Tightening Torque 10 Nm
9. Tighten the injection pump mounting bolts.
Tightening Torque 23 Nm

OM600 ENGINE MECHANICAL 1B3-69
10. Install the fuel filter.
11. Install the vacuum pump.
12. Install the power steering pump.
13. Install the power steering pump pulley.
Tightening Torque 25 Nm
Tightening Torque 10 Nm
Tightening Torque 23 Nm
Tightening Torque 32 Nm
14. Install the guide pulley bracket.
Tightening Torque 9 Nm

1B3-70 OM600 ENGINE MECHANICAL
15. Install the guide pulley (22) and fit the closing cover (20).
16. Replace the gasket (3) and install the cylinder head cover
(2).
17. Install the cooling fan belt pulley and fan clutch.
18. Install the belt tensioning device and then install the belt.
19. Install the cooling fan.
20. Fill the engine oil and check oil leaks by running the engine.
Tightening Torque 23 Nm
Tightening Torque 10 Nm

1B3-72 OM600 ENGINE MECHANICAL
Tools Required
601 589 03 43 00 Oil Seal Assmbler
Removal Procedure
1. Remove the bolts (3, 6) from end cover, By pulling out the
lugs (arrow), remove the cover.
Notice
Be careful not to damage the oil pan gasket.
2. Remove the radial seal (4) with care not to damage the
sealing surface.
Installation Procedure
1. Thoroughly clean the sealing surface of end cover and apply
Loctite 573.
2. Clean the groove of radial seal.
3. Apply Loctite 573 on the bolts and install the end cover.
Tightening Torque 10 Nm
Notice
Be careful not to damage the oil pan gasket.
4. Install the inner oil seal assembler to the crankshaft flange.
Oil Seal Assembler 601 589 03 43 00