1998 NISSAN GT-R warning

ELECTRIC SUPER HICAS
Trouble Diagnosis
with CONSULT (Cont'd)
connector for
'@g SELECT DlAG MODE
SELF-DIAG RESULTS i
DATA MONITOR
ACTIVE TEST
ECM PART NUMBER
u
1 I lhil SELECT MONITOR ITEM I 1
SELECTION FROM MENU
I Il
I
START I
ACTIVE TEST PROCEDURE
After connecting CONSULT to data link connector, start the
engine.
Touch "START", "HICAS and "ACTIVE TEST".
Touch 'SIMULATE" and "SELECT MONITOR ITEM".
Turn the steering wheel right or left to make the rear actuator
operate.
Reference values in normal condition
-- -
0" (Neutral) I 2.4V I 2.4V I No (Approx OV)
Steering angle
sensor
ECM PART NUMBER
Rear steering
angle main sensor
--
R 90"
L 90"
After connecting CONSULT to data link connector, turn ignition
switch ON.
Touch "START', "HICAS" and "ECM PART NUMBER7'.
Part number printed on the control unit label and part number
shown on the CONSULT screen are as follows:
2-door model: 28505
AAI
00
4-door model: 28505 AAll 0
Trouble Diagnosis with Self-diagnosis
Rear steering
angle sub-sensor
4.4V
0.4V
DESCRIPTION
If the system detects some error while vehicle is running, it notifies
the driver of a malfunction
by turning ON the HICAS warning lamp,
and at the same time, it halts the normal control and enters the
fail-safe mode.
Motor current
SELF-DIAGNOSIS PROCEDURE
4.4V
0.4V
1. Start the engine.
2. Within 10 seconds after the engine has started, turn the steer-
ing wheel more than
20" right-to-left and repeat this
5 times or
more, and then depress the brake pedal
5 times or more.
Yes (Variable)

ELECTRIC SUPER HICAS
Trouble
Diagnosis with Self-diagnosis (Cont'd)
DIAGNOSTIC ITEM INPUT
1. Move the vehicle one or two meters at a very low speed.
2. Turn the steering wheel more than 20" right-to-left once or
more.
Example: Motor power supply and steering
angle neutral signal are abnormal.
1s ,
2H z
ON
OFF
/ r Second / / I I display
Tens Units Tens
Units starts.
Example: Motor power supply and steering
angle neutral signal are abnormal.
1s- ,
0.8s A - ,2S , ,1.8S -
ON I-- '1 7, OFF- -.-- -
5s 55 1s 1.8s v".2S I_
/ -j- &lnd,
display
Tens Units Tens Units starts.
/
(12) (23) STE0109D
DISPLAY OF SELF-DIAGNOSTIC RESULTS
The results of self-diagnosis are shown by flash patterns of HlCAS BR
warning lamp.
Display when past data shows that fail-safe function
has been activated previously
Only an abnormal item is indicated by the pattern shown in the ~8 left figure. The pattern is repeated.
Display when past data shows that fail-safe function
has not been activated previously EL
If all items are normal, HlCAS warning lamp flashes at a fre-
quency of
4 Hz. sD
If system is in fail-safe mode, only an abnormal item is indi-
cated by the pattern shown in the left figure. The pattern
is
repeated.
MALFUNCTION CODE CHART
Malfunction code No. 1 Diagnostic item
11 I Control unit
2
1 [ ~ze speed signal
12
13
22 I Steering angle signal
Motor
power supply
Motor output --
23 ]Steering angle neutral signal
24 I Rear steering angle main sensor signal
2
5 I Rear steering angle sub-sensor signal
33
I Engine speed signal
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
If past record shows that fail-safe function has been activated
previously, use CONSULT, or leave the battery disconnected for
more than
30 minutes to clear the memory.

ELECTRIC SUPER HICAS
Symptom Chart (Cont'd)
Diagnostic item
Self-diagnosis CONSULT
-
Mal-
f unc-
tion
code No.
Cannot enter self-diagnosis mode. Diagnostic item
HICAS warning lamp is not tumed ON by switching the ignition
3N.
IICAS warning lamp is turned ON by switching the ignition ON but
s not turned OFF by starting the engine.
llumination of HICAS warning lamp has occurred after engine
;tarted. Diagnostic
item
Steering effort does not change with vehicle speed.
rhere is an abnormal noise.
Self-diagnosis with CONSULT displays
"CODE54".

TROUBLE DIAGNOSES - Su~plemental Restraint Svstem (SRS)
-
connector for
SELF-DlAG [CURRENT] C
* NO SELF DIAGNOSTIC
FAILURE INDICATED.
FURTHER TESTING
MAY BE REQUIRED. $ *
-1 PRINT
Preliminary Check
Check battery voltage and specific gravity.
When battery voltage drops to less than approx. 9V, the
"AIR BAG" warning lamp starts flashing (indicating a mal-
function).
Gj
Check the connections of component connectors.
Check that the fuse is not blown.
3F
Trouble Diagnoses with CONSULT
SELF-DIAGNOSIS PROCEDURE
Connect CONSULT to data link connector on the vehicle.
Turn ignition switch "ON".
83
Touch "AIR BAG" on the CONSULT screen.
Touch an appropriate mode key on "SELECT DlAG MODE"
screen.
gL
The self-diagnostic result for the selected mode is displayed.
Repair or replace the malfunctioning part according to the
self-
diagnostic result.
89
Touch "PRINT, if printout is required.
After
repairing the malfunction, touch "SELF-DIAG
[CURRENT]", and after checking that "NO SELF DIAGNOSTIC
FAILURE INDICATED" is shown on the display, touch
"ERASE.
For seat belt pre-tensioner system, the diagnostic proce-
dure
is completed when "NO SELF DIAGNOSTIC FAILURE
INDICATED"
is displayed.
FURTHER TESTING MAY BE REQUIRED. * *
* NO SELF DIAGNOSTIC
FAILURE INDICATED.
t
PRINT SRS609
9. Return to "SELECT DlAG MODE" screen and touch "SELF-
DlAG
[PAST]".
10. After checking that "NO SELF DIAGNOSTIC FAILURE INDI-
CATED" is displayed on the "SELF-DIAG [PAST]" screen, fin-
ish the diagnosis.

TROUBLE DIAGNOSES - Supplemental Restraint System (SRS)
Trouble Diagnoses with CONSULT (Cont'd)
TROUBLE DIAGNOSIS RECORD
If a malfunction has occurred but is not recorded on seif-diagnosis,
it may be caused by some past malfunction. In such a case, past
malfunctions can be found
by selecting "TROUBLE DlAG
RECORD" in Diagnosis mode.
The "TROUBLE DlAG RECORD" can be selected for SRS air
bag system only.
Trouble Diagnoses without CONSULT
SRS AIR BAG SYSTEM
Self-diagnosis
The diagnosis modes are User mode and Diagnosis mode.
Switching between the two modes is accomplished by using
ignition switch
and driver door switch.
When lamp is not flashing (indicating no malfunction) in User mode, operating the door switch cannot change
the mode to Diagnosis mode.
When no malfunction is detected in Diagnosis mode, turning the ignition switch from "OFF" to "ON" changes
the mode to User mode. SRB0395D
User mode
Turn diver door switch 'ON" and 'OFF" at least 5 times within 7 seconds after sw~tching the
No malfunction is detected. (Lamp OFF)
IGN SW: ON
ON
OFF- 7 sec.
System is malfunctioning. (Lamp flashes)
Diagnosis
mode
User mode
ON
OFF
b A k Turn driver door switch "ON" and "OFF at
least 5, times
within 7 seconds after sw~tching
the ignition "ON".
IGN SW: OFF to ON IGN SW: OFF to ON
ignition
"ON".
-
- -
0.5 see. 0.5 sec.
Air bag is deployed or all of diagnosis sensor unit, air bag power supply circuit and AIR BAG warning lamp cir-
cuit are malfunctioning. (Lamp ON)
ON
OFF
Either air bag sensor unit or AIR BAG warning lamp circuit is malfunctioning. (Lamp OFF)
IGN SW: ON
OFF + SRB0412D
The display indicating a malfunction (flashes) keeps operation
until reset. If, however, the malfunction is a low battery volt-
age (less than 9V), the display changes from flashing to nor-
mal operation when the battery voltage has returned to normal
(more than
9V).

TROUBLE DIAGNOSES - Supplemental Restraint System (SRS)
Trouble Diagnoses without CONSULT (Cont'd)
Diaanosis mode
Malfunctioning part
- --- -
Diagnostic item Warning
lamp fiash pattern
No malfunction is detected.
IGN SW: ON
AIR BAG warning lamp (LED) is checked. Unit: sec.
Driver air bag module
Two flashes
Short-circuit between wires I
Diagnosis sensor unit Unit
malfunction
u H-+H 2 2 0.5 Unit: sec.
Seven flashes
ON F
OFF 7 3 C --
y HHft H 2 0.5 2 Unit: sec.
Passenger air bag mod-
ule Open
circuit
Eight flashes
Shorted to power supply circuit ON
OFF 7 Shorted to ground
Short-circuit between wires
2 2 0.5 2 Unit: sec.
Driver side air bag
- -
Open circuit One flash
ON
OFF
7
2 3 0.5 Unit: sec.
Passenger side air bag
Driver satellite sensor
Passenger satellite sen-
sor
After
after
Open circuit I Two flashes
w+ 2 6.5 % Unit: sec.
Satellite sensor malfunction I
Open circuit I Three flashes - -- -- -
Shorted to power supply circuit I -- -- pp - -
Shorted to ground
Short-circuit between wires Diagnosis sensor unit malfunction
Satellite sensor malfunction
Open circuit Shorted to power supply circuit
Shorted to ground
Short-circuit between wires
ON 1
OFF 7
Unit: sec.
Four flashes ON
OFF
2 0.5 0.5 Unit: sec.
Diagnosis sensor unit malfunction I -04630

TROUBLE DIAGNOSES - Supplemental Restraint System (SRS)
Trouble Diagnoses without CONSULT (Cont'd)
How to erase self-diagnostic results (Reset)
After repairing the system and while staying in Diagnosis mode,
check that the system has returned to normal; then, turn
tion switch
"OFF' and then back "ON". The mode returns
mode and the diagnosis record is erased.
SEAT BELT PRE-TENSIONER SYSTEM
Self-diagnosis
Only User mode is available.
.User mode
Driver seat belt
(Seat belt buckle
switch) Warning
lamp flash pattern
Malfunctioning part
Fastened (OFF)
IGN SW: ON
Unfastened (ON)
Fastened (OFF)
I IGN SW: ON System restored
+o.s Sec.
Unfastened (ON)
( IGN SW: ON Fastened I
-'n~0.5 sec.
I I -+OS sec. I
&
Driver and passenger
seat belt pre-tensioner
circuits
Diagnosis sensor unit
the igni-
to User
Diagnostic item
No malfunction is
detected.
No malfunction is
detected.
Shorted to power sup-
ply circuit
Open circuit
Shorted to ground
Diagnosis sensor unit
malfunction
The display indicating a malfunction (flashes) changes to the display indicating no malfunction when the malfunction is
repaired.
After pre-tensioner is activated, the warning lamp stays "ON".

TROUBLE DIAGNOSES - Supplemental Restraint System (SRS)
Symptom Chart
Trouble phenomenon I Malfunctioning unit I Possible cause
I I Warning lamp and internal circuit of combination meter are
BAG warning lamp does
not turn on. (All other warn-
ing lamps turn on.)
L-L .. AIR BAG warning lamp does I
I Harness between diagnosis sensor unit and combination
AIR
BAG warning lamp circuit
Air bag power supply circuit
not turn off (always ON). (AIR BAG warning lamp circuit
I meter is faulty (open).
faulty.
P-$ ;
Harness between
diagnosis sensor unit and combination 'bJ
Diagnosis sensor unit
0 Air bag power fuse has blown.
0 Air bag power harness is faulty.
meter is faulty
(shorted).
Diagnosis sensor unit is faulty.
I23
Diagnosis sensor unit
0 Internal circuit of combination meter is faulty. BR
Diagnosis sensor unit is faulty.
AIR BAG warning lamp
flashes.
When driver seat belt is
fas-
lamp does not illuminate for
seconds. (All other warning
Low battery voltage (Less than 9V)
Conduct either diagnosis with CONSULT (self-diagnosis, trouble diagnosis record) or diagnosis ST
without CONSULT (self-diagnosis), and repair the malfunctioning part.
After repairing the malfunctioning part, erase the memory for malfunction record.
Warning lamp and internal circuit of combination meter are 1
tened(buckleswitchisoff)
and ignition switch is turned
on, the SEAT BELT warning
1 Air bag power
SEATBELTwarninglampcircuit
circuit faulty.
Harness between
diagnosis sensor unit and combination HA
meter is faulty (open).
Air bag power fuse has blown.
0 Air bag power harness is faulty.
lamps illuminate.)
When driver seat belt is fas-
tened (buckle switch is off)
When driver seat belt is fas-.
I I
Diagnosis sensor unit
and ignition switch is turned
on, the SEAT BELT warning
lamp does not turn off
7 sec-
onds later.
tened (buckle switch is off)
I I
-.
0 Diagnosis sensor unit is faulty.
SEAT
BELT warning lamp circuit
,
and ignition switch is turned
on, the SEAT BELT warning
fa> Harness between diagnosis sensor unit and combination su
meter is faulty (shorted).
Driver seat belt buckle switch circuit
Diagnosis sensor unit
Seat belt pre-tensioner circuit
Harness between combination meter and driver seat belt
buckle switch is faulty (shorted).
Driver seat belt buckle switch is faulty (sticking).
Diaqnosis sensor unit is faultv.
Conduct either diagnosis with CONSULT or diagnosis with-
out CONSULT, and repair the malfunctioning part.
lamp turns on, and
7 sec- I I
onds later, flashes.
When driver seat belt is not
fastened (buckle switch is on)
I I Driver seat belt buckle switch ground harness is faulty
lamp turns off about
7 sec-
onds later.
and ignition switch
is tumed
on, the SEAT BELT warning
tence).
Driver seat
belt buckle switch circuit I !::);eat belt buckle switch is faulty (contact intermit-
If the flashing of AIR BAG warning lamp is caused by low battery voltage, self-diagnosis mode cannot be switched from User
mode to Diagnosis mode. In this case, diagnosis with CONSULT displays "NO SELF-DIAGNOSTIC FAILURE INDICATED".