1998 NISSAN GT-R oil filter

TROUBLE DIAGNOSES
Line Pressure Test (Cont'd)
JUDGEMENT OF LINE PRESSURE TEST
At idle
speed
At stall
speed Judgement
Line pressure is low in all
positions.
Line pressure is low in par-
ticular position.
Line pressure is
high.
Line pressure increase is
poorer than that measured at
idle speed.
Line pressure increases but
does not reach specification.
Line pressure is low in par-
ticular position. Possible
causes
Pressure supply system malfunction or low oil pump output
Examples:
0 Oil pump wear
Control piston damage
Pressure regulator valve or plug sticking, and weak spring
Fluid pressure leakage between oil strainer and pressure regulator valve through oil Eg
Pump
Low idle speed
After line pressure is supplied from manual valve, fluid pressure may leak between devices
or circuits of corresponding position.
1
Malfunctions of sensors or pressure regulation function. El
Examples:
Misadjustment of throttle position sensor
PJT fluid temperature sensor damaged ST
Poor operation of line pressure solenoid (stuck with OFF status, clogged filter, or open
harness)
Pressure modifier valve sticking F%
Pressure regulator valve or plug sticking
Malfunctions of sensors or pressure regulation function
Examples:
EILA
Misadjustment of throttle position sensor
TCM, ECM.TCM damaged la
Poor operation of line pressure solenoid (stuck or shorted with ON status)
Pressure regulator valve and plug sticking
Pressure modifier valve sticking
sf$
Pilot valve sticking and pilot filter clogged
Malfunctions of pressure supply system, sensors, or pressure regulation function
Examples:
Misadjustment of throttle position sensor
Control piston damage
Poor operation of line pressure solenoid, and filter sticking or clogged
Pressure regulator valve and plug sticking
Pressure modifier valve sticking
Pilot valve sticking and pilot filter clogged
After line pressure is supplied from manual valve, fluid pressure
may leak between devices
or circuits of corresponding position.
Stall Test
1. Check engine oil level. If necessary, add oil.
2. Drive vehicle for approximately 10 minutes until A/T fluid
reaches normal operating temperature between
50 and 80°C,
and check A/T fluid level. If necessary, add AfT fluid.
When ambient temperature is
20°C,
A/T fluid operating tem-
perature usually becomes between 50 and
80°C for approxi-
mately
10 minutes' drive in urban traffic.
3. Set parking brake and block wheels.
4. Statt engine, depress brake pedal, and move selector lever to
"D" position.

ENGINE MECHANICAL I RB~ODE (UB) ]
STANDARD AND REPAIR LIMIT
Firing order I 1-5-3-6-2-4
Compression pressure
MPa
(kg/cm2)/rpm
Distortion limit mm
- - -- --- - Ignition advance device
Electronically-controlled ignition advance
Engine
oil capacity
e
Spark plug standard
Limit
. Limit
of variation between cylinders
Intake manifold
Intake manifold collector
Exhaust manifold
Cylinder head
Cvlinder block
lgnition timing (during no feed back control) 1.23
(1 2%)/300
0.93 (9.5)1300
0.1 (1.0)/300
0.1 0.1
0.3
0.2
0.1
Without filter
With filter
MakerlTypeISpark
plug gap mm
Engine idling speed
W'
Idle base speed (during no feed back control)
rPm
Density of
COIHC at idling speed
Wppm Approx.
3.8
Approx. 4.2
NG WPFR5G-11 11.0
- 1
-1
650-.50
(N or P position for
A/T)
600 (N or P position for AlT)
Less than O.l/Less than 50
I New I Used I Limit
Valve
clearance
(INTIEXH)
mm
Deflection
amount of accessory V-belt
Measured with tension gauge
N (kg) Hot
engine
.
Cold engine (at ambient temperature)
Measured by pushing at 98 N (10 kg)
mm 0.36+0.062/0.53+0.062
0.31 1~,0.04/0.50i0.04
Fuel tank capacity
e
Engine coolant total capacity [with reservoir tank (max. level)] e
Thermostat opening temperature [start to open - full open]
"C
Radiator cap opening pressure
MPa (kg/cm2) Approx.
65
Approx. 9.4 82 - 95
0.06
- 0.1 0 (0.6 - 1 .O)
A/C compressor belt
Power
steering pump belt
Fan belt
Power steering pump belt
1 8-10 1 10-12 1 16
667
- 755
(68
- 77)
A/C compressor belt 1 6-8 1 7-9 / 12
Fan belt
1 3-5 1 4-6 1 7.5
559 - 637
(57
- 65)
SEC.117 Power steering
Fan belt pump be1 t
284 (29)

ENGINE MECHANICAL
STANDARD AND REPAIR LIMIT
Firing order
Compression pressure
MPa (kg/cm2)/rpm
-
Intake manifold
Intake manifold collector
--- - Standard Limit
Limit of variation between
cylinders
0.1
0.1
Distortion limit mm
Engine oil capacity
P
Spark plug
Deflection amount of accessory
V-belt Power steering pump
belt
I
- -- - - 1.26 (1 2.8)/300
0.96 (9.8)/300
0.1
(1 .OY300
Measured with tension gauge Exhaust
manifold
Cylinder head
Cylinder block
Without filter
With filter
MakerKype/Spark
plug gap
mrn
I "
650.-50 (N or P position for CVT)
600 (N or P position for AIT)
Less than O.l/Less than 50
15U600
0.36~0.06210.53~0.062
0.31 -.0.04/0.50~0.04
Approx. 65
Approx. 9.4
82 - 95
0.06 - 0.10 (0.6 - 1 .O)
"
Engine idling speed rpm
Idle base speed (during no feed back control)
rpm
Density of
COIHC at idling speed
%/ppm
Ignition timing (during no feed back control)
BTDCO/rpm
I NC compressor err
0.3
0.2
0.1
Approx. 3.8
Approx. 4.2
NGWPFR5G-11/1.0
- 1.1
lanition
advance device
1
Valve clearance (INTIEXH) mm
(kg)
/ Fan belt Electronicallv-controlled
ianition
advance
Hot engine
Cold engine (at ambient temperature)
I power steerina DU~D belt 1 8-10
Fuel tank capacity
Q
Engine
coolant total capacity [with reservoir tank (max. level)] e
Thermostat opening temperature [start to open - full open] OC
Radiator cap opening pressure
MPa (kg/crn2)
,
I Fan belt 1 3-5
Measured
by pushing at 98
N (10 kg)
mm
I SEC.! I7 Power steering I
*I I 1
AK compressor belt 1 6-8
Fan belt pump beit
Used 1 Limit

ENGINE MECHANICAL
STANDARD AND REPAIR LIMIT
Distortion limit mm
- - Intake manifold
Intake manifold collector
1 -5-3-6-2-4
1.20 (1
2.2)/300
0.90 (9.2)/300
0.1 (1.0)/300
Firing order
-- - 0.1
0.1
- -- - ( Cylinder block 0.1
Compression
pressure
MPa
(kg/cm2)/rpm
Exhaust manifold
Cvlinder head
Engine oil capacity Standard
Limit
-
Limit of variation between cylinders
0.3
0.2
- - -- - Spark plug I ~akerfl~~e/~~ark plug gap mm r NGKPFRGG-11/1.0 - 1.1
Without
filter
'with
filter
ignition advance device
I Electronically-controlled ignition advance
Approx.
3.9
Aoorox.
4.3
Engine idling speed
rPm
Idle
base speed (during no feed back control)
Pm
650-e50
(N or P position for
A/T)
600 (N or P position for AQ
Density of COIHC at idling speed
Wppm
Ignition timing (during no feed back control)
BTDCO/rpm Less
thanbl~ess than 50
15dY600
Valve clearance
(INT/EXH) mm
Deflection amount of accessory V-belt Hot
engine
Cold engine (at ambient temperature)
Measured
with tension gauge
(kg)
I
SEC.117 Power steering
Fan belt pump belt
0.36+0.062/0.53i0.062
0.3
1 20 .04/0.50a0.04
Fuel tank capacity
4
Engine coolant total capacity [with reservoir tank (max. level)] t
Thermostat opening temperature [start to open - full open]
OC
Radiator cap opening pressure
MPa (kg/cm2)
Power steering pump belt
Measured by pushing at 98
N (1 0 kg)
mm Approx.
65
Approx. 9.4
82
- 95
0.06
- 0.1 0 (0.6 - 1 .O)
New 1 Used 1 Limit
AfC
compressor belt
Fan belt
,
667 - 755
(68
- 77)
Power steering pump belt
' AfC compressor belt
Fan belt
559 - 637 284 (29)
(57 - 65)
667
- 755
(68
- 77)
667
- 755
(68
- 77)
559 - 637 284 (29)
(57 - 65)
559 - 637 284 (29) (57 - 65)
8-
10
6-8
3 - 5
- 10 - 12 16
7-9 12
4
- 6 7.5