1998 JAGUAR X308 battery

Generator and Regulator - Voltage Regulator
Removal and Installation
Removal

1. Disconnect the batt ery ground cable.
Remove the battery cover.
2. Remove the generator from the vehicle. Refer to Operation
86.10.02.

3. Remove the nut from the main terminal and remove the
insulator.

4. Remove the ground tag.
1. Remove the nut which secures the ground tag.
2. Remove the screw which secures the ground tag and remove the tag.
5. Remove the two remaining nuts which secure th e rear cover
and remove the cover.

2. Note the locating flat on the insulator and in the rear cover.
3. Install the nut to the main terminal.
10. Install the generator to the vehicle. Refer to Operation
86.10.02.
11. Connect the battery and in stall the battery cover.
Refer to the Battery Reconnection Procedure 86.15.15.

Audio Unit - Capacitor
Removal and Installation
Removal
Installation



1. Disconnect the batt ery ground cable.
Remove the battery cover.
2. Raise the vehicle on a ramp.

3. Remove the suppr ession module.
1. Disconnect the multi-plug from the mounting bracket clip.
2. Disconnect the multi-plug.
3. Remove the bolts which secure the suppression module to the mounting bracket.
4. Remove the su ppression module.
1. Installation is th e reverse of the re moval procedure.
2. Reconnect the battery ground cable and fit the battery cover.
Reset the radio inform ation and the clock.

Speakers - Door Speaker
Removal and Installation
Removal
Installation

1.
Disconnect battery ground cable (IMPORTANT, see SRO
86.15.19 for further information).
2. Remove door casing; refer to 76.34.01.

3. Remove speaker from door casing.
Remove four screws.
Remove speaker.
1. Installation is a reversal of the removal procedure.
2. Reconnect battery ground cable (IMPORTANT, see SRO
86.15.15 for further information).

Speakers - Rear Door Speaker
Removal and Installation
Removal
Installation

1.
Disconnect battery ground cable (IMPORTANT, see SRO
86.15.19 for further information).
2. Remove door casing; refer to 76.34.04.

3. Remove speaker from door casing.
Remove four screws.
Remove speaker.
1. Installation is a reversal of the removal procedure.
2. Reconnect battery ground cable (IMPORTANT, see SRO
86.15.15 for further information).

Exterior Lighting - Fog Lamp Switch
Removal and Installation
Removal
Installation



1. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Remove instrument pa nel veneer panel. Refer to 76.47.24.

3. Remove combined front and rear fog lamp switch pack.
Use a small screwdriver to re lease upper retaining tag.
Position switch for access to connector.
Disconnect connector and remove switch.
1. Position switch pack at instrument panel.
2. Connect harness connector to switch pack
3. Install switch pack in panel, ensuring that retaining tangs are
fully seated.
4. Install instrument panel veneer panel. Refer to 76.47.24.
5. Connect ground cable to batter y terminal and install battery
cover. Refer to 86.15.15.

Exterior
Lighting - License Plate Lamp
Rem
oval and Installation
Remov

al
Installation
1.

Remove battery cover and disconnect ground cable from battery
terminal. Refer to 86.15.19.
2. Remove trunk lamp assemblies. Refer to 86.45.16
3. Remove trunk lid upper trim finisher. Refer to 76.43.79.

4.

From inside trunk lid, press tang at each side of lamp and push
lamp outwards.

5.

Withdraw number plate lamp from trunk lid for access and
disconnect lamp harness multiplug.

6.

Remove and discard foam seal from lamp.
1. Install new foam seal to number plate lamp.
2. Position number plate lamp at trunk lid and connect harness
multiplug.
3. Install number plate lamp in trunk lid aperture ensuring that seal
seats correctly.
4. Install trunk upper trim finisher. Refer to 76.43.79.
5. Install trunk lamp assemb lies. Refer to 86.45.16.
6. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.

Interior Lighting - Luggage Compartment Lamp
Removal and Installation
Removal
Installation

1.
Remove battery cover and disc onnect ground cable from
battery terminal.Refer to 86.15.19.

2. Carefully release lamp tangs from trunk lid trim, position lamp
for access, disconnect harness multiplug and remove lamp from trunk.
1. Position lamp at trunk lid and connect harness multiplug.
2. Ensuring that harness is routed correctly, finally position and
fully seat lamp in trunk lid liner.
3. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.