1998 JAGUAR X308 brake

Parking Brake and Actuation - P
arking Brake Control
Re
mo
val and Installation
Remov
a
l
W
A
RNING: BRAKE DUST, IF INHALED CAN DAMAGE YOUR
HEALTH. ALWAYS REMOVE BRAKE DUST USING A VACUUM
BRUSH. DO NOT USE A COMPRESSED-AIR LINE TO DISPERSE BRAKE DUST INTO THE ATMOSPHERE.
CAUTION: Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
1. Position vehi cl
e on a four-post lift.
2. Release parking brake.

3. Releas
e tension on parking brake cable.
Slacken bu

t do not remove adjustment nut.

4. Releas
e parking brake cable.
Remo

ve clip.
Re
mo
ve clevis pin.
5. Remove driver seat for access . Refer to operation 76.70.01.
6. Remove trim from hand lever. Refer to operation 76.13.63.
7. Carefully reposition carpet from around hand lever for access.

8. Disconnect park ing-br
ake, warning-light switch connector.
9. Remove hand lever from vehicle.

I
nstallation

Re
move bolts.
R

emove lever.

10
.
Remove gasket.

11
.
Remove warning-light switch from lever.
R
emove screws.
Re

move switch.

1. Inst
all warning-light switch to hand lever.
Install and tigh

ten
screws to 3 Nm.
2. Install gasket to handbrake lever.

3. Instal
l hand lever to vehicle.
Install and tighten bolts to 2

2-28 Nm.

4. Connect park
ing-brake, warnin
g-light switch connector.
5. Reposition carpet.
6. Install trim to hand lever. Refer to operation 76.13.63.
7. Install driver seat. Refer to operation 76.70.01.
8. Make sure parking brake is in the released position.

9. Connect p a
rking brake cable.
Align ca
ble
.
Inst
al
l clevis pin.
Inst
al
l clip.
10. Adjust parking brake. Refer to operation 70.35.10.

Parking Brake and Act
uation - Parking Brake Control Shroud
Re
moval and Installation
Remov

al
Installation

1.
Position ha
ndbrake lever fully up.
2. Remove trim from handbrake lever.
1. Release press stud at to p of handbrake lever trim.
2. Ease lower moulding away from boss at base of lever and slide trim upwards.
1. Slide trim over handbrake lever and position lower moulding
over boss.
2. Fasten press stud at top of trim.
3. Check that 'J' gate selector is in position P.
4. Lower handbrake lever, checki ng for freedom of movement.
5. Pull handbrake lever fully up.

Parking Brake and Actuation - P
arking Brake Shoes
Re
mo
val and Installation
Remov
a
l
W
A
RNING: BRAKE DUST, IF INHALED CAN DAMAGE YOUR
HEALTH. ALWAYS REMOVE BRAKE DUST USING A VACUUM
BRUSH. DO NOT USE A COMPRESSED-AIR LINE TO DISPERSE BRAKE DUST INTO THE ATMOSPHERE.
CAUTION: Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
1. Ra
ise rear of vehicle and support
on stands. Refer to section
100-02.
2. Remove both rear wheels.
3. Remove both rear brake discs. Refer to operation 70.10.13.

4. Re
move front shoe retaining pin.
Align hub ac

cess hole with retaining pin.
Turn pin until
it rel
eases
from backing plate.

5. Remove adju ster assembly.
Move front shoe forwards.

Remove adju
ster assembly.

6. Re
move rear shoe retaining pin.
Al
ign hub ac
cess hole with retaining pin.
Turn pin until
it rel
eases
from backing plate.
7. Remove brake shoes from parkin g brake lever-mechanism and
remove shoes from vehicle.
8. Remove return sp rings from shoes.

I
nstallation

1
. Remove upper return spring.
2. Remove lower return spring.
9. Remove brake dust and clean components, see WARNING
above.
10. Repeat procedure to remove pa rking brake shoes on opposite
side of vehicle.

1. I
nstall brake shoes to vehicle.
Install brake shoes to parkin
g brake lever-me
chanism in
the arrangement shown.

2. N
OTE: Make sure retaining pin is seated correctly in backing
plate.
Install rear shoe retaining pin.
Align hu
b access hole.
Inst

all retaining pin.

3. Inst
all adjuster assembly.
Lubricate adjuster

mechanism
with appropriate grease.
Move
front shoe forwards.
Inst

all adjuster assembly.
4. NOTE: Make sure retaining pin is seated correctly in backing

plate.
Install front
shoe
retaining pin.
Align hu
b acc
ess hole.
Inst
al
l retaining pin.
5. Make sure brake shoes are seat ed correctly in adjuster and
lever mechanism.
6. Repeat procedure to install parking brake shoes on opposite
side of vehicle.
7. Install both rear br ake discs. Refer to operation 70.10.13.
8. Set parking brake. Refer to operation 70.35.37.
9. Fit rear wheels. See section 204-04.
10. Remove stands an d lower vehicle.

Parking Brake and Ac
tuat
ion - Parking Brake Warn ing Indicator Switch
Re
moval and Installation
Remov

al
Installation
1. R
emove driver seat for access. Refer to 76.70.01.
2. Raise hand lever fully.
3. Remove trim from hand lever. Refer to operation 76.13.63.

4. R
emove screws securing
switch to hand lever.

5. Di
sconnect electrical connector from switch.

1. Di
sconnect electrical connector from switch.
2. Install switch to hand lever.
Install and tigh
ten
screws to 3 Nm.