1998 JAGUAR X308 light

Exterior Lighting - Front Side Marker Lamp Bulb
Removal and Installation
Removal

1. Applying firm hand pressure to front end, pivot lamp assembly
for access to rear end.

2. Exercising care to avoid dama ging paintwork, use a small
screwdriver at rear end of lamp, to press and release retaining
tang.

3. Withdraw lamp from bumper for access and disconnect harness multiplug.

4. Rotate bulb holder 1/4 turn counter-clockwise to release it
from lamp assembly.
5. Withdraw bulb from holder.

Exterior Lighting - Front Turn Signal Lamp Bulb
Removal and Installation
Removal

1. Applying firm hand pressure to inner end, pivot indicator lamp
assembly for access to outer end.

2. Exercising care to avoid dama ging paintwork, use a small
screwdriver at outer end of lamp, to press and release retaining clip.

3. Withdraw lamp from bumper for access and disconnect harness multiplug.

4. Rotate bulb holder 1/8 turn to release it from lamp assembly.
5. Withdraw bulb holder and remove bulb.

Exterior Lighting - Headlamp Assembly
Removal and Installation
Removal
1. Remove radiator grill. Refer to 76.55.03.
2. Remove radiator grill surro und. Refer to 76.55.15.
3. Remove headlamp trim panel. Refer to 76.11.23.

4. Disconnect headlamp levelling actuator if fitted.

5. Disconnect headlamp assembly harness connector.

6. Remove headlamp assembly to body lower nuts.
7. Remove headlamp to body upper nuts.

Exterior Lighting - Headlamp Leveling Motor
Removal and Installation
Removal
Installation



1. Disconnect harness multiplug from headlamp levelling
actuator.

2. Rotate actuator 1/4 turn inwards, tilt forward end downward
and withdraw assembly from headlamp.
1. With forward end tilted downward , position actuator assembly
on headlamp.
2. Align actuator with headlamp an d rotate it 1/4 turn outwards
to engage and fully seat.
3. Connect harness multiplug to actuator.
4. Carry out headlamp beam al ignment to the appropriate
alignment equipment instructions.

Exterior Lighting - High Beam Headlamp
Removal and Installation
Removal
Installation
1. Remove headlamp assembly fo r access. Refer to 86.41.33.

2. Release bulb holder securing tangs and position holder for
access.

3. Rotate pilot bulb holder 1/4 turn and withdraw holder.
4. Invert headlamp assembly.

5. Release headlamp unit adju sting screws and pivot.
1. Install headlamp unit on adjusting screw and pivot seats.

Exterior Lighting - High Beam Headlamp Bulb
Removal and Installation
Removal
Installation

1.
Open hood and install fender cover.

2. Release headlamp bulb holder locking tangs and remove holder from headlamp.
3. CAUTION: If the bulb is to be re-fitted, the glass must
not be touched with the bare hand . Failure to observe this caution
will result in premature bulb failure
Position bulb holder for access and remove bulb.
1. CAUTION: Headlamp bulbs are of the halogen type and
must not be handled with bare hands. Failure to observe this
caution will result in premature bulb failure.
Install headlamp bulb in holder.
2. Install bulb holder in headlamp ensuring that securing tangs
are fully seated.
3. Remove fender cover and close hood.

Exterior Lighting - High Mounted Stoplamp
Removal and Installation
Removal
Installation

1. Remove lamp cover.
1. Depress two tangs at base of lamp carrier and withdraw cover.

2. Disconnect lamp harness connector.

3. Remove module.
1. Release spring clips at each end of lamp lens module and withdraw module from carrier.

4. Remove lamp carrier.
Release lamp carrier lower securing tangs.
Slide carrier upwards to release and remove carrier from
backlight.
1. Ensure that rubber insulating pads are installed on lamp
carrier.

Exterior Lighting - High Mounted Stoplamp Bulb
Removal and Installation
Removal
Installation

1. Remove cover from stop lamp.
1. Depress two tangs at base of lamp cover and withdraw cover.

2. Remove lamp module.
1. Release spring clips at each end and remove lamp module from carrier.

3. CAUTION: Exercise care to avoid contact with reflective
surfaces.
Withdraw lens and remove re levant bulb from module.

1. CAUTION: Exercise care to avoid contact with reflective
surfaces.
Install new bulbs as nece ssary and install lens.
2. Install module.
1. Slide module into carrier and seat securing clip at