1997 TOYOTA SUPRA center console
[x] Cancel search: center consolePage 22 of 1807
MT06N-01
D01920
Shift Lever Knob
Upper Console Panel
Shift Lever Boot
RetainerShift Lever Retainer
Shift and Select Lever
Boot No.1
x5
Service Hole
Cover
Starter
Pipe Support Bracket
Service Hole Cover
Ground Cable
Engine Under Cover
Oxygen SensorExhaust Front Pipe Exhaust Tail Pipe Exhaust Center PipePropeller ShaftCrossmember Brace
Heat Insulator Engine Rear
Mounting
Adjusting Washer BushingTransmission Shift Lever
Clutch Release Cylinder
N´m (kgf´cm, ft´lbf)Shift and Select Lever
Boot No.2
Oxygen Sensor Cover
: Specified torqueRear Engine Mounting
Member
Non-reusable part Gasket
Gasket
Gasket
Gasket
19 (195, 14)
72 (730, 53)
12 (120, 9)
79 (805, 58)
49 (500, 36)
19 (195, 14)
56 (570, 41)
12 (120, 9)
37 (380, 27)
12 (120, 9)
25 (260, 19)13 (135, 10)
39 (400, 29)
5.5 (55, 48 in.´lbf)
13 (130, 9)
13 (130, 9)
5.5 (55, 48 in.´lbf)
Heat Insulator72 (730, 53)
39 (400, 29)
25 (250, 18)19 (195, 14)
19 (195, 14)
7.8 (80, 69 in.´lbf)
Bushing
19 (195, 14)
Normal Roof:
Sport Roof:
58 (590, 43)
Transmission
Crossmember
Brace
20 (200, 14)
25 (250, 18)
58 (590, 43)
MT-2
- MANUAL TRANSMISSION (V160)MANUAL TRANSMISSION UNIT
1570 Author: Date:
1997 SUPRA (RM502U)
MANUAL TRANSMISSION UNIT
COMPONENTS
Page 491 of 1807
SRS AIRBAG COMPONENT REPLACEMENT (cont'd) PAGE 5 of 6
Component Replacement Notes
Note 1 ± Replace the following items:
Instrument panel
Center console bracket support
Note 2 ± Replace the following items if deformed:
Instrument panel
Instrument panel reinforcement
Glove compartment
Glove compartment door
Note 3 ± Replace the following items:
Instrument panel reinforcement
Glove compartment
Glove compartment door
Note 3a ± Replace the following items:
Instrument panel
Instrument panel reinforcement
Glove compartment door
Note 4 ± If the SRS wire harness assembly is damaged:
Use a repair wire specially designed for use in the SRS airbag system at the front
sensor (P/N 82988±24010).
OR
Replace the entire wire harness assembly.
Note 4a ± Replace wire harness if damaged.
Repair only if wire harness connector is damaged.
Note 4b ± Replace wire harness if damaged.
Note 5 ± Replace the following items if deformed:
Steering wheel
Spiral cable
Note 6 ± Replace center airbag sensor assembly if:
Center airbag sensor assembly has been found faulty in troubleshooting
Center airbag sensor assembly has been found faulty during the following checks:
1. Deformation of the bracket or case
2. Vinyl seal broken
3. Damage to connector
Center airbag sensor assembly has been dropped.
Page 496 of 1807
SRS COMPONENT REPLACEMENT (cont'd) PAGE 4 of 4
Component Replacement Notes
Note 1 ± Visually inspect and replace the following items if deformed:
Instrument panel and center console bracket support
Note 2 ± Visually inspect and replace the following items if deformed:
Instrument panel and Instrument panel reinforcement
Glove compartment and glove compartment door
Note 2a ± Same as note 2 without involving the glove compartment.
Note 3 ± If the SRS wire harness is damaged only at the connectors to the front
sensors:
Use a repair wire specially designed for use in the SRS airbag system at the front sensor
(PN 82988±24010/50010/33010).
OR
Replace the entire wire harness assembly.
Note 3a ± Replace the entire wire harness if damaged or has been found to be faulty
during troubleshooting.
Note 4 ± Replace the following items if deformed or if diagnostic tests show a fault:
Steering wheel (If the horn button contact plate has been deformed, never attempt to
repair it±always replace the steering wheel).
Spiral cable
Note 5 ± Replace center airbag sensor assembly if:
Center airbag sensor assembly has been found faulty in troubleshooting.
Center airbag sensor assembly shows evidence of the following:
1. Deformation of the bracket or case
2. Vinyl seal broken
3. Damage to connector
Center airbag sensor assembly has been dropped.
Note 6 ± Replace side impact sensors and side airbag assembly with seat cover if
deployed. Side airbag circuits are independent from each other, and one
side may deploy while the other does not.
Note 7 ± 1998 Tacoma is equipped with a passenger airbag cutoff switch. If the
switch is ªOFFº when impact occurs, replace the switch. If the switch is in
the ªONº position when impact occurs, and the passenger airbag deploys,
check the switch as directed by the Repair Manual.
Page 501 of 1807
SRS AIRBAG COMPONENT REPLACEMENT (cont'd) PAGE 5 of 6
Component Replacement Notes
Note 1 ± Replace the following items:
Instrument panel
Center console bracket support
Note 2 ± Replace the following items if deformed:
Instrument panel
Instrument panel reinforcement
Glove compartment
Glove compartment door
Note 3 ± Replace the following items:
Instrument panel reinforcement
Glove compartment
Glove compartment door
Note 3a ± Replace the following items:
Instrument panel
Instrument panel reinforcement
Glove compartment door
Note 4 ± If the SRS wire harness assembly is damaged:
Use a repair wire specially designed for use in the SRS airbag system at the front
sensor (P/N 82988±24010).
OR
Replace the entire wire harness assembly.
Note 4a ± Replace wire harness if damaged.
Repair only if wire harness connector is damaged.
Note 4b ± Replace wire harness if damaged.
Note 5 ± Replace the following items if deformed:
Steering wheel
Spiral cable
Note 6 ± Replace center airbag sensor assembly if:
Center airbag sensor assembly has been found faulty in troubleshooting
Center airbag sensor assembly has been found faulty during the following checks:
1. Deformation of the bracket or case
2. Vinyl seal broken
3. Damage to connector
Center airbag sensor assembly has been dropped.
Page 1308 of 1807
S00926
Upper Console Panel
Shift & Select Lever BootShift Lever
Shift Lever Knob
Shift Control Rod
Fuel Return Hose
Fuel Inlet Hose A/T
PS Vane Pump
A/C CompressorGround Strap
PS Pump Bracket M/T
Clutch Release Cylinder (M/T)Rear Support Member
Exhaust Pipe AssemblyPropeller Shaft
PS Pressure Feed Hose
No.2 Front Exhaust Pipe
Pipe Support BracketHeated Oxygen SensorHeat InsulatorCenter Floor
Crossmember Brace Ring
Ring Gasket
Gasket
Gasket
Non-reusable partSport Roof EM-56
- ENGINE MECHANICAL (2JZ-GTE)ENGINE UNIT
1161 Author: Date:
1997 SUPRA (RM502U)
Page 1581 of 1807
R07283
A
B
Matchmarks SR-12
- STEERINGTILT STEERING COLUMN
1896 Author: Date:
1997 SUPRA (RM502U)
4. REMOVE THESE PARTS:
(See page BO-54)
(a) Console upper panel
(b) Cluster finish panel
(c) Cluster finish panel RH
(d) Cluster finish panel LH
(e) Cluster finish center panel
(f) Finish panel
(g) Finish lower LH panel
(h) Heater to register No.2 duct
5. REMOVE COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Remove the 4 screws.
(b) Disconnect the connectors and airbag connector.
6. REMOVE SPIRAL CABLE
(See page BE-16)
NOTICE:
Do not disassemble the cable or apply oil to it.
7. DISCONNECT INTERMEDIATE SHAFT
(a) Place matchmarks on the intermediate shaft and control
valve shaft.
(b) Loosen bolt B and remove bolt A.
8. REMOVE STEERING COLUMN ASSEMBLY
(a) Remove the brake pedal return spring.
(b) Disconnect the connectors.
(c) Loosen the hole cover clamp.
(d) Remove the 4 column assembly set nuts.
Page 1590 of 1807
SR142-01
W02982
R07283
Matchmarks A
B
R05740
Red Mark
- STEERINGTILT STEERING COLUMN
SR-21
1905 Author: Date:
1997 SUPRA (RM502U)
INSTALLATION
1. INSTALL STEERING COLUMN ASSEMBLY
(a) Torque the 4 column assembly set nuts.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(b) Connect the connectors.
(c) Install the brake pedal return spring.
(d) Tighten the hole cover clamp.
2. CONNECT INTERMEDIATE SHAFT
(a) Align the matchmarks on the intermediate shaft and con-
trol valve shaft.
(b) Torque the bolt A.
Torque: 35 N´m (360 kgf´cm, 26 ft´lbf)
(c) Torque the bolt B.
Torque: 35 N´m (360 kgf´cm, 26 ft´lbf)
3. INSTALL SPIRAL CABLE
(See page BE-16)
4. INSTALL COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Tighten the 4 screws.
(b) Connect the connectors and airbag connector.
5. INSTALL THESE PARTS:
(See page BO-59)
(a) Heater to Register No.2 duct
(b) Finish lower LH panel
(c) Finish panel
(d) Cluster finish center panel
(e) Cluster finish panel LH
(f) Cluster finish panel RH
(g) Cluster finish panel
(h) Console upper panel
6. INSTALL COLUMN UPPER AND LOWER COVERS
Tighten the 5 screws.
7. CENTER SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Turn the spiral cable counterclockwise by hand until it be-
comes harder to turn the cable.
(c) Rotate the spiral cable clockwise about 3 turns to align the
marks.
HINT:
The spiral cable will rotate about 3 turns to either left or right of
the center.