Page 182 of 1807
BE0DY-02
Z09367
Right Turn
Left Turn
Connector ºAº
BE1843
2
Turn Signal Light Bulbs (21W)13
Z09334
BE-26
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
2004 Author: Date:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT TURN SIGNAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Left turnA1 - A5Continuity
Neutral-No continuity
Right turnA1 - A8Continuity
If continuity is not as specified, replace the switch.
2. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the terminal 2 to battery positive (+) terminal and
the terminal 3 to battery negative (-) terminal.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, check that the bulbs flash.
HINT:
The turn signal lights should flash between 60 and 120 times
per minute.
3. INSPECT HAZARD WARNING SWITCH CONTINUITY
ConditionTester connectionSpecified condition
Switch OFF7 - 10Continuity
Switch ON7 - 8
4 - 5 - 6 - 9Continuity
Illumination circuit2 - 3Continuity
If continuity is not as specified, replace the switch.
BE3QR-01
Page 195 of 1807
Z18230
Brake Fluid Level Warning Switch
Parking Brake Switch
Telltale Light LH
Telltale Light RHVehicle Speed Sensor
Light Failure Sensor
DOME Fuse
Combination Meter
Door Courtesy Switches GAUGE Fuse
ECU-B Fuse
IGN Fuse
PANEL Fuse
TAIL Fuse Integration
Fuel Sender Gauge
: Engine Coolant Temperature Sensor
: Engine Oil Level Sensor
: Low Oil Pressure Warning Switch
: Park/Neutral Position Switch
: Vehicle Speed Sensor 2JZ-GE2JZ-GTE
1
5
4
3
2 Relay R/B No.2
J/B No.1
Meter Circuit
1
1
5 4
3
2 1
2
3
4
5
BE0E7-01
- BODY ELECTRICALCOMBINATION METER
BE-39
2017 Author: Date:
1997 SUPRA (RM502U)
COMBINATION METER
LOCATION
Page 197 of 1807
I02078
Cruise Control Indicator :Fuel Gauge
:Engine Coolant Temperature Gauge
:Tachometer
:Speedometer
D.R.L. :Daytime Running Light
* :Engine Oil Level Delay Circuit
F
E
T
S
F
E
T
S C8
A10
A11
A9
A8
A13
C11
C10
B13
B12
B2
A1
C7
C5
A14
A7
A6
A3
C1
C2
C13
A5P
R
N
D
2
LB4
B10
B6
B7
B8
B11
B1
C9
A16
C4
C6
A15
A2
B3
C12 Fuel Level Warning
MANU Indicator
O/D OFF Indicator
Brake Warning
Bulb Check Relay
TRAC Indicator
Right Turn Indicator
High Beam Indicator
Master Warning
Illumination
SNOW IndicatorLeft Turn Indicator
No. Wire Harness Side
Brake Fluid Level Warning Switch
Parking Brake Switch
USA:TAIL (RH) Fuse, PANEL Fuse
Headlight Dimmer Switch
ECT ECU
Cruise Control ECU
TRAC ECU
Ground (Engine)
Engine Coolant Temperature Sender Gauge
Fuel Sender Gauge
Ground (Signal)
Turn Signal Switch
Starter Relay Generator L Terminal Igniter
Park/Neutral Position Switch (A/T Vehicle) A1
2
3
5
6
7
8
9
10
11
13
14
15
16
BGAUGE Fuse
O/D OFF Switch
USA:TAIL (RH) Fuse, PANEL Fuse
Park/Neutral Position Switch (P)
Park/Neutral Position Switch (N)
ECT ECU
Ground (Power)
Park/Neutral Position Switch (D)
Park/Neutral Position Switch (2)
Park/Neutral Position Switch (L) Park/Neutral Position Switch (R) 1
2
3
6
7
8
10
11
124
13
Engine Oil Level Sensor
Turn Signal Switch
Ground (Power)
Fuel Sender Gauge
GAUGE Fuse
Vehicle Speed Sensor (Terminal 2)
Vehicle Speed Sensor (Terminal 3)
USA:TAIL (RH) Fuse, PANEL Fuse
Light Control Rheostat Telltail Light RH (Terminal 11)
Telltail Light LH (Terminal 1)
Telltail Light LH (Terminal 6) 1
2
6
7
8
10
11
124
135
9 CCANADA:D.R.L. No.3 Relay
Clutch Start Switch (M/T Vehicle)
CANADA:D.R.L. No.3 Relay
CANADA:D.R.L. No.3 Relay
- BODY ELECTRICALCOMBINATION METER
BE-41
2019 Author: Date:
1997 SUPRA (RM502U)
Page 198 of 1807
I02082I02081
I02080
I02079
I05022
Security Indicator
TRAC OFF Indicator
Low Oil Pressure Warning
Engine Oil Level Warning
Malfunction Indicator
ABS Indicator
No.
Combination Meter (Terminal B2)
ECM
ECM
Low Oil Pressure Warning Switch
Combination Meter (Terminal B4)
TRAC ECU, Traction Solenoid Relay
Ground
Theft Deterrent and Door Lock ECUWire Harness Side
1
2
3
4
5
6
8
9
10
No.Wire Harness Side
GAUGE Fuse
ECU-B Fuse
IGN Fuse
PANEL Fuse
Vehicle Speed Sensor (Terminal 3)
Ground
DOME Fuse
Light Control Rheostat
Combination Meter (Terminal B1)
Generator Terminal
Door Courtesy Switch
Integration Relay (Terminal 9)
Light Failure Sensor Center Airbag Sensor 1
2
3
4
5
6
8
107
11
12
14
15
16
18GAUGE Fuse
PPS ECU, Cruise Control ECU, ECM OD/TRIP
Meter
Open Door Warning
Seat Belt Warning
SRS Warning 8
6 5
3
4
110
2 9
7
10
5
14
18
12
16
15
114
6
1
8
3
2Air Conditioning Amplifier Telltale Light LH:
Telltale Light RH:
Rear Light Warning
Discharge Warning BE-42
- BODY ELECTRICALCOMBINATION METER
2020 Author: Date:
1997 SUPRA (RM502U)
2. TELLTALE LIGHT:
Page 201 of 1807
N08911
B
AC
N08959
F
1/2
E
Z09401
Ignition
Switch
BatteryWarning Light
N08933
N08993
- BODY ELECTRICALCOMBINATION METER
BE-45
2023 Author: Date:
1997 SUPRA (RM502U)
6. INSPECT FUEL RECEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
Between terminalsResistance (W)
A - BApprox. 269.7
A - CApprox. 123.5
B - CApprox. 146.2
If resistance value is not as specified, replace the fuel receiver
gauge.
7. INSPECT FUEL SENDER GAUGE RESISTANCE
Measure the resistance between terminals 2 and 3 for each
float position.
Float position: mm (in.)Resistance (W)
F: Approx. 33.8 (1.331)Approx. 4.0
1/2: Approx. 44.8 (1.764)Approx. 55.0
E: Approx. 141.1 (5.555)Approx. 107.0
If resistance value is not as specified, replace the sender
gauge.
8. INSPECT FUEL LEVEL WARNING LIGHT
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 1 and 3 on the wire harness side con-
nector.
(c) Turn the ignition switch ON, check that the warning light
lights up.
If the warning light does not light up, test the bulb or inspect wire
harness.
9. INSPECT FUEL LEVEL WARNING SWITCH OPERA-
TION
(a) Apply battery positive voltage between terminals 1 and 3
through a 3.4 W test bulb, check that the bulb lights up.
HINT:
It will take a short time for the bulb to light up.
(b) Submerge the switch in fuel, check that the bulb goes out.
If operation is not as specified, replace the sender gauge.
Page 203 of 1807
N06640
BE0044
Ignition
Switch
BatteryWarning Light
N09645
ON
OFF
N09646
ON
OFF
Z07431
Ignition
Switch
BatteryWarning Light
- BODY ELECTRICALCOMBINATION METER
BE-47
2025 Author: Date:
1997 SUPRA (RM502U)
13. INSPECT LOW OIL PRESSURE SWITCH CONTINUITY
(a) Check that there is continuity between terminal and
ground with the engine stopped.
(b) Check that there is no continuity between terminal and
ground with the engine running.
HINT:
Oil pressure should be over 29 kPa (0.3 kgf/cm
2, 4.3 psi)
If operation is not as specified, replace the switch.
14. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, check that the warning light
lights up.
If the warning light does not light up, test the bulb or inspect wire
harness.
15. INSPECT ENGINE OIL LEVEL WARNING SWITCH
CONTINUITY
(a) Check that there is continuity between terminal with the
switch in each position.
(b) Heat the switch to above 60°C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the
switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
16. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON. Check that the warning light
lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
Page 204 of 1807
N08966
BE1217
Ignition
Switch
BatteryWarning Light
N09510
BE0044
Ignition
Switch
BatteryWarning Light BE-48
- BODY ELECTRICALCOMBINATION METER
2026 Author: Date:
1997 SUPRA (RM502U)
17. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
CONTINUITY
(a) Remove the reservoir tank cap and strainer.
(b) Disconnect the connector.
(c) Check that there is no continuity between terminals with
the switch OFF (float up).
(d) Use syphon, etc. to take fluid out of the reservoir tank.
(e) Check that there is continuity between terminals with the
switch ON (float down).
(f) Pour the fluid back in the reservoir tank.
If operation is not as specified, replace the switch.
18. INSPECT BRAKE FLUID LEVEL WARNING LIGHT
(a) Disconnect the connector from the brake fluid warning
switch.
(b) Release the parking brake pedal.
(c) Connect terminals on the wire harness side of the level
warning switch connector.
(d) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or wire har-
ness.
19. INSPECT PARKING BRAKE SWITCH CONTINUITY
(a) Check that there is continuity between terminal and
switch body with the switch ON (switch pin released).
(b) Check that there is no continuity between terminal and
switch body with the switch OFF (switch pin pushed in).
If operation is not as specified, replace the switch or inspect
ground point.
20. INSPECT PARKING BRAKE WARNING LIGHT
(a) Disconnect the connector from the parking brake switch
and the brake fluid warning switch.
(b) Ground terminal on the wire harness side connector.
(c) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or inspect wire
harness.
Page 205 of 1807
Z07425
12
10
111 2 345
6
789
Wire Harness Side
Z07426
Ignition
Switch
BatteryWarning Light
- BODY ELECTRICALCOMBINATION METER
BE-49
2027 Author: Date:
1997 SUPRA (RM502U)
21. INSPECT LIGHT FAILURE SENSOR CIRCUIT
Disconnect the connector from the sensor and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 - GroundConstantContinuity*
2 - GroundConstantContinuity*
9 - GroundConstantContinuity*
10 - GroundConstantContinuity*
11 - GroundConstantContinuity
12 - GroundConstantContinuity*
3 - GroundLight control switch position OFFNo Voltage
3 - GroundLight control switch position TAIL or HEADBattery positive voltage
4 - GroundIgnition switch position LOCK or ACCNo voltage
4 - GroundIgnition switch position ONBattery positive voltage
7 - GroundStop light switch position OFFNo voltage
7 - GroundStop light switch position ONBattery positive voltage
8 - GroundEngine condition StopNo voltage
8 - GroundEngine condition RunningBattery positive voltage
*: There is the resistance because this circuit is grounded
through the bulb.
If circuit is as specified, replace the sensor.
If the circuit is not as specified, inspect the circuits connected
to other parts.
22. INSPECT LIGHT FAILURE WARNING LIGHT
(a) Disconnect the connector from the light failure sensor and
ground terminal 4 on the wire harness side connector.
(b) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or inspect wire
harness.
