1997 SUBARU LEGACY rotor

B2M0315B
2) Install inner and outer rotors in their original positions.
3) Install oil relief valve and relief spring.
4) Install oil pump cover.
Tightening torque:
T1: 5
+1
0N⋅m (0.5+0.1
0kg-m, 3.6+0.7
0ft-lb)
T2: 44.1±3.4 N⋅m (4.5±0.35 kg-m, 32.5±2.5 ft-lb)
B2M0319A
E: INSTALLATION
Installation is in the reverse order of removal.
Do the following:
1) Apply fluid packing to matching surfaces of oil pump.
Fluid packing:
THREE BOND 1215 or equivalent
2) Replace O-ring with a new one.
3) Be careful not to scratch oil seal when installing oil
pump on cylinder block.
CAUTION:
Apply fluid packing to oil pressure switch threads
before installation.
Fluid packing:
THREE BOND 1215 or equivalent
8
2-4SERVICE PROCEDURE
1. Oil Pump

1. Engine Lubrication System
Before troubleshooting, make sure that the engine oil level
is correct and no oil leakage exists.
Trouble Possible cause Corrective action
1. Warning light remains
on.1) Oil pressure switch
failureCracked diaphragm or oil leakage within switch Replace.
Broken spring or seized contacts Replace.
2) Low oil pressureClogged oil filter Replace.
Malfunction of oil by-pass valve of oil filter Clean or replace.
Malfunction of oil relief valve of oil pump Clean or replace.
Clogged oil passage Clean.
Excessive tip clearance and side clearance of oil
pump rotor and gearReplace.
Clogged oil strainer or broken pipe Clean or replace.
3) No oil pressureInsufficient engine oil Replenish.
Broken pipe of oil strainer Replace.
Stuck oil pump rotor Replace.
2. Warning light does not
go on.1) Burn-out bulb Replace.
2) Poor contact of switch contact points Replace.
3) Disconnection of wiring Repair.
3. Warning light flickers
momentarily.1) Poor contact at terminals Repair.
2) Defective wiring harness Repair.
3) Low oil pressureCheck for the same pos-
sible causes as listed in
1.—2)
17
2-4DIAGNOSTICS
1. Engine Lubrication System

No. Part Name Part Number Dimension mm (in) Application
1 Control piston2500 cc 31235AA000—030
13.5
0.030
0.037(0.53150.0012
0.0015), 13.50.023
0.030(0.53150.0009
0.0012),
13.50.016
0.023(0.53150.0006
0.0009), 13.50.009
0.016(0.53150.0004
0.0006)Adjusting side clear-
ance of oil pump
2200 cc 31235AA040 — 070
2 Cam ring 31241AA001 — 03117
0.010
0.017(0.66930.0004
0.0007), 170.003
0.010(0.66930.0001
0.0004),
17+0.004
0.003(0.6693+0.0002
0.0001), 17+0.011
+0.004(0.6693+0.0004
+0.0002)Adjusting side clear-
ance of oil pump
3 Vane (Oil pump) 31243AA000 — 03017
0.030
0.037(0.66930.0012
0.0015), 170.023
0.030(0.66930.0009
0.0012),
170.016
0.023(0.66930.0006
0.0009), 17+0.009
+0.016(0.6693+0.0004
+0.0006)Adjusting side clear-
ance of oil pump
4 Rotor (Oil pump) 31240AA000 — 03017
0.030
0.037(0.66930.0012
0.0015), 170.023
0.030(0.66930.0009
0.0012),
170.016
0.023(0.66930.0006
0.0009), 17+0.009
+0.016(0.6693+0.0004
+0.0006)Adjusting side clear-
ance of oil pump
5Thrust washer
(Reverse clutch)31299AA000 — 0600.7, 0.9, 1.1, 1.3, 1.5, 1.7, 1.9
(0.028, 0.035, 0.043, 0.051, 0.059, 0.067, 0.075)Adjusting end play of
reverse clutch drum
6 Bearing race 803031021 — 0270.8, 1.0, 1.2, 1.4, 1.6, 1.8, 2.0
(0.031, 0.039, 0.047, 0.055, 0.063, 0.071, 0.079)Adjusting total end
play
7 Retaining plate 31567AA350 — 4004.6, 4.8, 5.0, 5.2, 5.4, 5.6 (0.181, 0.189, 0.197, 0.205,
0.213, 0.220)Adjusting clearance
of reverse clutch
8 Retaining plate31567AA340,
31567AA190 — 2603.4, 3.6, 3.8, 4.0, 4.2, 4.4, 4.6, 4.8, 5.0
(0.134, 0.142, 0.150, 0.157, 0.165, 0.173, 0.181, 0.189,
0.197)Adjusting clearance
of high clutch
9 Retaining plate31567AA010,
31567AA060 — 1104.0, 4.2, 4.4, 4.6, 4.8, 5.0, 5.2
(0.157, 0.165, 0.173, 0.181, 0.189, 0.197, 0.205)Adjusting clearance
of forward clutch
10 Retaining plate 31567AA410 — 4708.0, 8.2, 8.4, 8.6, 8.8, 9.0, 9.2
(0.315, 0.323, 0.331, 0.339, 0.346, 0.354, 0.362)Adjusting clearance
of overrunning clutch
11Retaining plate
No. 231667AA180 — 2506.5, 6.8, 7.1, 7.4, 7.7, 8.0, 8.2, 8.4
(0.256, 0.268, 0.280, 0.291, 0.303, 0.315, 0.323, 0.331)Adjusting clearance
of low and reverse
brake
12Pressure plate
(Front)31593AA151 — 1813.3, 3.7, 4.1, 4.5
(0.130, 0.146, 0.161, 0.177)Adjusting clearance
of transfer clutch
13Thrust bearing
(35x53xT)806536020,
806535030 — 070,
0903.8, 4.0, 4.2, 4.4, 4.6, 4.8, 5.0
(0.150, 0.157, 0.165, 0.173, 0.181, 0.189, 0.197)Adjusting end play of
transfer clutch
14Washer
(38.1 x 50 x T)803038021 — 0230.95, 1.00, 1.05
(0.0374, 0.0394, 0.0413)Adjusting backlash
of differential bevel
gear
15 Drive pinion shim 31451AA050 — 1000.150, 0.175, 0.200, 0.225, 0.250, 0.275
(0.0059, 0.0069, 0.0079, 0.0089, 0.0098, 0.0108)Adjusting drive pin-
ion height
5
3-2SPECIFICATIONS AND SERVICE DATA
1. Automatic Transmission and Differential

3. Oil Pump
B3M0354A

1Retainer


2Return spring


3Pin


4Friction ring


5O-ring


6Cam ring


7Vane ring


8Vane


9Rotor


10Oil pump cover


11Thrust washer


12Seal ring (R)


13Seal ring (H)


14Thrust needle bearing


15Thrust washer

16Air breather hose


17Drive pinion shaft


18Roller bearing


19Shim


20Test plug


21Oil pump housing


22Pin


23Side seal


24Control piston


25Plane seal


26Gasket


27O-ring


28Oil seal


29Oil seal retainer


30Drive pinion collar

31Lock washer


32Lock nut


33O-ring


34O-ring


35Nipple


36Stud bolt
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 7±1 (0.7±0.1, 5.1±0.7)
T2: 13±1 (1.3±0.1, 9.4±0.7)
T3: 18±5 (1.8±0.5, 13.0±3.6)
T4: 25±2 (2.5±0.2, 18.1±1.4)
T5: 39±3 (4.0±0.3, 28.9±2.2)
T6: 41±3 (4.2±0.3, 30.4±2.2)
T7: 113±5 (11.5±0.5, 83.2±3.6)
12
3-2COMPONENT PARTS
3. Oil Pump

G3M0446
2) Remove the oil pump cover.
NOTE:
Lightly tap the end of the stator shaft to remove the cover.
G3M0447
3) Remove the retainer and return spring. Then remove
the rotor, two vane rings and nine vanes.
G3M0448
4) Remove the cam ring and control piston.
Also remove the O-ring, friction ring, two side seals, and
plain seal.
G3M0449
5) Remove two seal rings (R) and two seal rings (H).
B: INSPECTION
1) Make sure that each component is free of harmful
gouges, cuts, and dust.
90
3-2SERVICE PROCEDURE
7. Oil Pump Assembly

G3M0450
2) Selection of oil pump components (rotor, vanes, control
piston and cam ring)
(1) Using a micrometer, measure the height of the
rotor, vanes, control piston and cam ring in at least four
positions. (Measure the height at one place for each of
the nine vanes.)
NOTE:
Remove the control piston seals when measuring.
Remove the friction ring from the cam ring when mea-
suring.
G3M0451
(2) Using a depth gauge, measure the depth of the oil
pump housing from the contact/sliding surface of the
above mentioned component parts in the same manner
as above.
G3M0452
(3) Make sure that the clearances are within the speci-
fied wear limits. If the wear limit is exceeded, select
pump components so that the standard clearance can
be obtained.
Unit: mm (in)
Part name Wear limit Standard value
Rotor, control piston,
vanes0.054
(0.0021)0.030—0.044
(0.0012—0.0017)
Cam ring0.034
(0.0013)0.010—0.024
(0.0004—0.0009)
NOTE:
Select vanes which are the same height as the rotor.
G3M0453
C: ASSEMBLY
1) Coat both the O-ring and friction ring with vaseline and
attach to the cam ring. Then fit them into the oil pump
housing.
91
3-2SERVICE PROCEDURE
7. Oil Pump Assembly

G3M0454
2) Install the vane ring, rotor and vanes into the housing
in this sequence.
G3M0455
3) Install the return spring and retainer between the hous-
ing and cam ring.
G3M0456
4) Install the control piston to the oil pump housing.
NOTE:
Fit the seal in the piston groove, with the red seals facing
the top side. (Two side seals and one plain seal are
attached.)
5) Set the rotor at the center of the housing bore. Apply
ATF abundantly to each rotary portion.
G3M0446
6) Install the oil pump cover.
Tightening torque:
25±2 N⋅m (2.5±0.2 kg-m, 18.1±1.4 ft-lb)
NOTE:
Align both pivots with the pivot holes of the cover, and
install the cover being careful not to apply undue force to
the pivots.
After assembling, turn the oil pump shaft to check for
smooth rotation of the rotor.
G3M0449
NOTE:
Install the oil seal retainer and seal rings (R) and (H)
after adjusting the drive pinion backlash and tooth contact.
92
3-2SERVICE PROCEDURE
7. Oil Pump Assembly

3. Oil Pump
B3M0354A

1Retainer


2Return spring


3Pin


4Friction ring


5O-ring


6Cam ring


7Vane ring


8Vane


9Rotor


10Oil pump cover


11Thrust washer


12Seal ring (R)


13Seal ring (H)


14Thrust needle bearing


15Thrust washer

16Air breather hose


17Drive pinion shaft


18Roller bearing


19Shim


20Test plug


21Oil pump housing


22Pin


23Side seal


24Control piston


25Plane seal


26Gasket


27O-ring


28Oil seal


29Oil seal retainer


30Drive pinion collar

31Lock washer


32Lock nut


33O-ring


34O-ring


35Nipple


36Stud bolt
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 7±1 (0.7±0.1, 5.1±0.7)
T2: 13±1 (1.3±0.1, 9.4±0.7)
T3: 18±5 (1.8±0.5, 13.0±3.6)
T4: 25±2 (2.5±0.2, 18.1±1.4)
T5: 39±3 (4.0±0.3, 28.9±2.2)
T6: 41±3 (4.2±0.3, 30.4±2.2)
T7: 113±5 (11.5±0.5, 83.2±3.6)
12
3-2COMPONENT PARTS
3. Oil Pump