1997 SSANGYONG KORANDO oil

M161 ENGINE MECHANICAL 1B2 -- 35
D AEW OO M Y_2000
Tools Required
116 589 20 33 00 Sliding Hammer
116 589 01 34 00 Threaded Pin
Removal & Installation Procedure
1. Remove the power steering belt pulley and A/C com-
pressor bracket.
2. Remove the oil line from power steering pump.
3. Rotate the crankshaft so that the piston of number,
cylinder is at ATDC20°.
4. Put the alignment marks (arrows) on the timing chain
and camshaft sprocket.
5. Remove the chain tensioner.
Installation Notice
Tightening Torque
72 -- 88 NSm (53 -- 65 lb-ft)
6. Remove the intake and exhaust camshaft sprocket
(remove the camshaft adjuster assembly in E23 en-
gine).
Installation Notice
Ti
ghteningTo rque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
TighteningTorque
2nd step: 60°±5°
Notice:The flange bolt is designed to be used only
once, so always replace with new one.
7. Remove the guide rail pin using the sliding hammer
116 589 20 33 00 (02) and the threaded pin 116 589
01 34 00 (03).
Notice:Apply the sealant on guide rail pin when installa-
tion.

1B2 -- 36 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
8. Unscrew the bolts (A).
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
9. Remove the belt pulley and vibration damper.
Installation Notice (Center Bolt)
Ti
ghteningTo rque
1st step: 200 + 20NSm
(148 + 15 lb-ft)
TighteningTorque
2nd step: 90°+10°
10. Unscrew the bolts (1, 2) on timing gear case cover
and remove the timing gear case cover.
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
Notice:Be careful not to damage the cylinder head gas-
ket.
11. Remove the radial shaft seal.
Notice:Installation note replace the seal with new one.
12. Clean the timing gear case cover and crankcase
sealing surface.
13. Replace the O -- ring with new one and apply the
sealant on the sealing surface.
Notice:Be careful not to stain the oil chamber of chain
tensioner with the sealant.
14. Installation should follow the removal precedure in
the reverse order.
15. Warm up the engine and check for oil leaks.

1B2 -- 38 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
Tools Required
601 589 03 43 00 Crankshaft Rear Seal Installer
Removal & Installation Procedure
1. Unscrew the bolts (1) and (5) and remove the closing
cover by pulling the rear cover lug (arrows).
Notice:Be careful not to damage the oil pan gasket.
2. Clean the sealing surface of the crankcase and the
rear sealing cover.
3. Check the radial shaft seal and replace it if necessary.
4. Apply the Loctite 573 to the rear cover sealing sur-
face.
5. Apply the engine oil to the dust lip of the radial shaft
seal.
Notice:Do not use the grease.
6. Install the crankshaft rear radial seal and the crank-
shaft sealing rear cover, using crankshaft rear seal in-
staller 601 589 03 43 00.
7. Install the crankshaft sealing rear cover mounting
bolts and remove the crankshaft rear seal installer
601 589 03 43 00.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
8. Installation should follow the removal procedure in
the reverse order.

1B2 -- 40 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
Components
1 Center Bolt (M18 x 50)
2 Center Bolt Washer
3 Vibration Damper and Pulley Assembly
4Key
5 Crankshaft Front Seal
6 Timing Gear Case Cover7 Crankshaft Sprocket (Camshaft Driven)
8 Crankshaft Sprocket (Oil pump Driven)
9 Crankshaft
10 Oil Pan
11 Oil Pan Gasket
12 Oil Pan Mounting Bolt (M6 x 22)
ServiceDataStandard
Permissble Deviation of The Vibration DamperRadial Runout0.6 mmp
Axial Runout0.6 mm

M161 ENGINE MECHANICAL 1B2 -- 43
D AEW OO M Y_2000
Tools Required
601 589 03 14 00 Crankshaft Front Seal Installer
Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice:Use a clean cloth not to damage the radial seal
mounting hole and the crankshaft.
2. Coat the radial sealing lip with engine oil.
3. Using the crankshaft front seal installer 601 589 03 14
00, assemble the radial seal .
4. Align the sleeve groove and the woodruff key and
tighten the center bolt until the center bolt and the
damper disk stop in the movement.
Installation Notice
Ti
ghteningTo rque
1st step: 200 + 20 NSm
(148 + 15 lb-ft)
TighteningTorque
2nd step: 90°+10°
5. Remove the crankshaft front seal installer 601 589 03
14 00, and install the belt pulley and the vibration
damper.
6. Check for leaks while operating the engine.

1B2 -- 44 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
CRANKSHAFT REAR RADIAL SEAL
Preceding Work: Removal of flywheel or drive plate
1 Special Tool
2 Special Tool3 Crankshaft Rear Seal
Tools Required
601 589 03 43 00 Crankshaft Rear Seal Installer
Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice:Use a clean cloth not to damage the radial seal
mounting hole and the crankshaft.
2. Install the special tool (2) to the crankshaft.
3. Apply the engine oil on the special tool (2).
Notice:Do not use the grease.
4. Install the radial seal on the inner parts assembler.
5. Press in the special tool (1) until the radial seal is
stopped.
6. Check for leaks while operating the engine.

M161 ENGINE MECHANICAL 1B2 -- 45
D AEW OO M Y_2000
CRANKSHAFT
Preceding Work: Removal of engine
Removal of cylinder head
Removal of timing gear case cover
Removal of crankcase sealing rear cover
Removal of oil pan
Removal of baffle plate
Removal of oil pump
1 Bearing Cap Bolt (M8 X 55 -- 10 pieces)
1ststep55NSm (41 lb-ft) .................
2nd step 90°rotation added
2 Bearing Cap
3 Upper Main Bearing4 Lower Main Bearing
5 Upper Thrust Bearing
6 Lower Thrust Bearing
8 Crankshaft

1B2 -- 46 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
Arrangement of the Thrust Bearing and the Main Bearing
1 Upper Main Bearing
2 Upper Thrust Bearing
3 Crankshaft
4 Lower Main Bearing
5 Lower Thrust BearingA Crankcase Side
B Bearing Cap Side (Oil Pan Side)
(1) -- (8) Weight Balance/Color Marking Point
j1 -- j5 Journal Main Bearing #1 -- #5
DColor Dot Marking
The color dot marking are put on the (1), (2), (4), (6), (8),
and it indicates the diameter of crankshaft journal by col-
or as below.