1997 SSANGYONG KORANDO torque

1B2 -- 10 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
11. Remove the hydraulic pipe of power steering.
Notice:Completely drain the oil.
12. Discharge the refrigerant from A/C system, and dis-
connect the discharge pipe and suction pipe from
the compressor.
13. Remove the fuel feed and return line.
Notice:Before removing the fuel lines, release the pres-
sure in the fuel system.
Installation Notice
Tightening Torque
21 -- 25 NSm (15 -- 18 lb-ft)
14. Disconnect the terminals from the generator.

1B2 -- 12 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
21. Separate the hose toward engine from canister
purge solenoid valve and canister. Refer toSection
1F2, Engine Control.
22. Remove the automatic transmission oil cooler line
retaining bolts from the automatic transmission side
and oil pan side.
23. Remove the automatic transmission oil cooler line
retaining bolts from engine side and oil pan side.
24. Separate the vacuum hose for brake booster.
25. Separate the other vacuum hoses.
26. By rotating the crankshaft from the front of engine,
remove the 6 torque converter mounting bolts from
the engine ring gear plate.
Installation Notice
Tightening Torque
42 NSm (31 lb-ft)

M161 ENGINE MECHANICAL 1B2 -- 13
D AEW OO M Y_2000
27. Remove the exhaust manifold and exhaust pipe.
Installation Notice
Tightening Torque
30 NSm (22 lb-ft)
28. Remove the transmission. Refer toSection 5A, Au -
tomatic Transmission.
29. Install a chain to the bracket of engine, by using a
hoist or crane.
30. Remove the engine mount nuts.
Installation Notice
Tightening Torque
70 NSm (52 lb-ft)
31. Carefully separate the engine assembly from the ve-
hicle.
32. Installation should follow the removal procedure in
the reverse order.

1B2 -- 18 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
GENERATOR
1 Bolt (M8 X 40, 3 pieces)
22.5-- 27.5 NSm (16.6-- 20.3 lb-ft) .............
2 Bolt (M8 X 70, 2 pieces)
22.5-- 27.5 NSm (16.6-- 20.3 lb-ft) .............3 Bolt (M8 X 85, 1 piece)
22.5-- 27.5 NSm (16.6--20.3 lb-ft) .............
4 Generator Bracket
Removal & Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the drive belt.
3. Remove the generator.
4. Unscrew the generator carrier bolts and remove the
carrier.
Installation Notice
Tightening Torque
25 NSm (18 lb-ft)
Notice:Apply 3 Nm of torque when mounting the bolt
(1) ; apply 25 Nm of torque when mounting the bolts (2),
and (3) ; and then tighten the bolt (1) with 25 Nm of
torque.
5. Installation should follow the removal procedure in
the reverse order.

M161 ENGINE MECHANICAL 1B2 -- 19
D AEW OO M Y_2000
ENGINE MOUNT
Removal & Installation Procedure
1. Unscrew the upper engine mount nuts and remove
the engine.
Installation Notice
Tightening Torque
70 NSm (52 lb-ft)
2. Unscrew the lower nuts.
Installation Notice
Tightening Torque
38 NSm (28 lb-ft)
3. Remove the hydraulic engine mounting insulator.
4. Installation should follow the removal procedure in
the reverse order.

1B2 -- 22 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
TENSIONING DEVICE
Preceding Work: Removal of tensioning device shock absorber
1 Bolt (M8 x 75, 2 pieces) +
Washer 22.5-- 27.5 NSm (16.6-- 20.3 lb-ft) ......
2 Bolt (M8 x 25, 1 pieces) +
Washer 22.5-- 27.5 NSm (16.6-- 20.3 lb-ft) ......3 Tensioning Device
4 Stud bolt
5 Tensioning Arm
Removal & Installation Procedure
1. Turn the stud bolt to counterclockwise.
2. Insert the pin (111 589 01 15 00) into the hole in ten-
sioning arm.
3. Unscrew the bolts (1, 2) and remove the tensioning
device.
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
4. Installation should follow the removal procedure in
the reverse order.

M161 ENGINE MECHANICAL 1B2 -- 23
D AEW OO M Y_2000
TENSIONING DEVICE SHOCK ABSORBER
1 End Cover
2 Bolt 40.5-- 49.5 NSm (29.9-- 36.5 lb-ft) .........
3 Tensioning Pulley
4 Bolt (M8 X 25) + Washer
22.5-- 27.5 NSm (16.6-- 20.3 lb-ft) .............5 Tensioning Device
6 Bolt (M8 X 35) + Washer
22.5-- 27.5 NSm (16.6--20.3 lb-ft) .............
7 Shock Absorber
Removal & Installation Procedure
1. Remove the end cover (1).
2. Remove the bolt (2) and remove the tensioning pulley
(3).
Installation Notice
Tightening Torque
40.5 -- 49.5 NSm
(29.9 -- 36.5 lb-ft)
3. Unscrew the bolts (4,6) and remove the shock ab-
sorber (7).
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)

M161 ENGINE MECHANICAL 1B2 -- 27
D AEW OO M Y_2000
Removal & Installation Procedure
1. Remove the intake air duct.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
2. Remove the spark plug cover.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
Notice:Release 3 screws from the spark plug cover and
remove the cover for M161 Engine coil.
3. Remove the spark plug connector and ignition cable.
4. Unscrew the bolts (3) and remove the head cover and
the gasket.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
Notice:Replace the gasket with a new one if necessary.
5. Installation should follow the removal procedure in
the reverse order.
6. Check for oil leaks by operating the engine.