1997 SSANGYONG KORANDO belt

SSANGYONG MY2002
8A-4 SEAT BELTS
REAR SEAT BELT
1 Rear Seat Belt Upper Anchor
2 Rear Seat Belt Webbing Hanger
3 Rear Center Seat Belt
4 Rear Center Seat Belt Buckle5 Rear Seat Belt Buckle
6 Rear Seat Belt Lower Anchor
7 Rear Seat Belt Retractor
8 Rear Seat Belt Dust Cover
KAA8A020

SEAT BELTS 8A-5
SSANGYONG MY2002


yy yy
yy
ON-VEHICLE SERVICE
THREE-POINT FRONT SEAT BELT
WITH PRETENSIONER
Caution: the sensing and diagnosis module (SDM)
can maintain sufficient voltage to deploy the air-
bags and pretensioner for 0.15 minutes after the
ignition is OFF and the fuse has been removed. If
the airbags or pretensioners are not disconnected,
do not begin service until one minute has passed
after disconnecting power to the SDM. Otherwise,
injury could result.
Removal and installation Procedure
1. Turn the ignition switch to LOCK and remove the
key.
2. Remove the plastic cap to reveal the lower B-pillar
seat belt anchor.
3. Remove the bolt and the lower B-pillar seat belt
anchor.
Installation Notice
KAA8A030
KAA8A040
4. Remove the lower quarter trim panel. Refer to Sec-
tion 9G, Interior Trim.
5. Disconnect the pretensioner connector.
6. Remove the bolt, screw and the seat belt retractor
(pretensioner).
Installation Notice
REPAIR PROCEDURES
Tightening Torque 45 Nm (33 lb-ft)
Tightening TorqueBolt 45 Nm (33 lb-ft)

SSANGYONG MY2002
8A-6 SEAT BELTS
KAA8A070
KAA8A060
KAA8A050
7. Remove the plastic cap to reveal the upper B-
pillar seat belt anchor.
8. Remove the bolt and B-pillar seat belt anchor.
Installation Notice
9. Installation should follow the removal procedure
in the reverse order.
Tightening Torque 45 Nm (33 lb-ft)
FRONT SEAT BELT HEIGHT
ADJUSTER
Removal and installation Procedure
1. Remove the front seat belt upper B-pillar anchor
bolt.
Installation Notice
2. Remove the rear seat belt upper anchor bolt.
Installation Notice
3. Remove the rear upper quarter trim panel. Refer
to Section 9G, Interior Trim.
4. Remove the bolts and seat belt height adjuster.
Installation Notice
5. Installation should follow the removal procedure
in the reverse order.
THREE-POINT REAR OUTBOARD
SEAT BELT
Removal and installation Procedure
1. Remove the plastic cap to reveal the seat belt
lower anchor bolt.
2. Remove the lower anchor bolt.
Installation Notice
Tightening Torque 45 Nm (33 lb-ft)
Tightening Torque 45 Nm (33 lb-ft)
Tightening Torque 45 Nm (33 lb-ft)
Tightening Torque 45 Nm (33 lb-ft)

SEAT BELTS 8A-7
SSANGYONG MY2002


yyyy yyyy
yyyy
KAA8A090
KAA8A100
KAA8A110
KAA8A080
3. Remove the lower quarter trim panel. Refer to Sec-
tion 9G Interior Trim.
4. Remove the bolt, screw and seat belt retractor.
Installation Notice
5. Remove the plastic cap to reveal the bolt.
6. Remove the upper anchor bolt.
Installation Notice
7. Installation should follow the removal procedure
in the reverse order.
TWO-POINT LAP REAR CENTER
SEAT BELT
Removal and installation Procedure
1. Fold the rear seat cushion.
2. Remove the bolts and the seat belt anchors.
Installation Notice
3. Installation should follow the removal procedure
in the reverse order.
CHILD SEAT TETHER ANCHOR
Removal and installation Procedure
1. Open the tether anchor access cap if equipped.
2. Remove the bolt and the tether anchor.
Installation Notice
3. Installation should follow the removal procedure
in the reverse order.
Tightening TorqueBolt 45 Nm (33 lb-ft)
Tightening TorqueBolt 45 Nm (33 lb-ft)
Tightening TorqueBolt 45 Nm (33 lb-ft)
Tightening TorqueBolt 19 Nm (14 lb-ft)

SSANGYONG MY2002
8A-8 SEAT BELTS
N•m
19
45
45
45Lb-Ft
14
33
33
33 Child Seat Tether Anchor Bolt
Seat Belt Anchor Bolt
Seat Belt Height Adjuster Bolt
Seat Belt Retractor BoltLb-In
-
-
-
-Application
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS

SEAT BELTS 8A-9
SSANGYONG MY2002
SCHEMATIC AND ROUTING DIAGRAM
SEAT BELT & TENSION REDUCER
KAA8A120

SECTION 8B
SUPPLEMENTAL RESTRAINTS SYSTEM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
other-wise noted.
TABLE OF CONTENTS
Description and Operation...................................8B-3
Supplemental Restraint System (SRS)..................8B-3
Airbag Modules...................................................8B-3
Front Seat Belt Pretensioners...............................8B-4
Sensing and Diagnostic Module (SDM)................8B-4
Airbag Warning Lamp ..........................................8B-5
Clock Spring........................................................8B-5
Wiring Harness Connectors..................................8B-5
Components Locator............................................8B-6
SRS Component and Wiring Location View...........8B-6
Diagnostic Information and Procedures..............8B-7
Diagnostic Trouble Codes (DTC)..........................8B-7
Scan Tool Diagnostics.........................................8B-7
Use of Special Tools............................................8B-7
Diagnostic Trouble Code Table............................8B-7
SRS Diagnostic System Check..........................8B-10
Sensing and Diagnostic Module (SDM)
Integrity Check...............................................8B-12
Airbag Warning Lamp Stays on with Ignition
Switch ON......................................................8B-14
DTCs - Internal Fault..........................................8B-16
DTCs 01 Driver Deployment Loop Shorted to
Voltage...........................................................8B-18
DTC 02 Passenger Deployment Loop Shorted to
Voltage...........................................................8B-20
DTC 03 Driver Seat Belt Pretensioner Shorted to
Voltage...........................................................8B-22
DTC 04 Passenger Seat Belt Pretensioner
Shorted to Voltage..........................................8B-24
DTC 05 Driver Deployment Loop Shorted to
Ground...........................................................8B-26
DTC 06 Passenger Deployment Loop Shorted to
Ground...........................................................8B-28
DTC 07 Driver Seat Belt Pretensioner Shorted to
Ground...........................................................8B-30DTC 08 Passenger Seat Belt Pretensioner
Shorted to Ground ..........................................8B-32
DTC 17 Driver Deployment Loop
Resistance High.............................................8B-34
DTC 18 Passenger Deployment Loop
Resistance High.............................................8B-38
DTC 19 Driver Seat Belt Pretensioner
Deployment Loop resistance High...................8B-40
DTC 20 Passenger Seat Belt Pretensioner
Deployment Loop Resistance High.................8B-42
DTC 21 Driver Airbag Deployment Loop
Resistance Low..............................................8B-44
DTC 22 Passenger Airbag Deployment Loop
Resistance Low..............................................8B-48
DTC 23 Driver Seat Belt Pretensioner
Deployment Loop resistance Low....................8B-50
DTC 24 Passenger Seat Belt Pretensioner
Deployment Loop Resistance Low..................8B-52
DTC 46 Airbag Warning Lamp Circuit Open or
Short to Ground/Battery..................................8B-54
DTC 47 Battery Voltage is Out of
Specification...................................................8B-56
Repair Instruction...............................................8B-58
On-Vehicle Service...............................................8B-58
Service Precaution.............................................8B-58
Disabling the Supplemental Restraint
System (SRS).................................................8B-58
Enabling the Supplemental Restraint
System (SRS).................................................8B-58
Handling, Installation and Diagnosis..................8B-58
Repairs and Inspections Required After an
Accident ........................................................8B-58
Accident with Deployment - Components
Replacement..................................................8B-58
Accident without Deployment - Component
Inspection......................................................8B-59

Sensing and Diagnostic Module (SDM)..............8B-59
Driver Airbag Module .........................................8B-60
Clock Spring......................................................8B-61
Passenger Airbag Module.................................8B-62
Front Seat Belt Pretensioner...............................8B-62
Airbag Module Deployment (In Vehicle)..............8B-63
Airbag Module Deployment
(Outside of Vehicle)........................................8B-65Deployed Airbag Module Disposal Procedure.....8B-66
SRS Wiring Repair.............................................8B-66
Specifications.....................................................8B-67
General Specification .........................................8B-67
Fastener Tightening Specifications.....................8B-67
Schematic and Wiring Diagrams.......................8B-68
Supplemental Restraint System.........................8B-68
Supplemental Restraint System Schematic
Diagram.........................................................8B-69