1997 RENAULT KANGOO Foult Finding - Injection Workshop Manual

JSA052.0
INJECTION
Fault finding - Fault charts
17
D7F 710
engine -
55 tracks
AFTER REPAIRErase the computer memory using G0** and carry out a road test.
Chart 3
CONT
Only refer to this customer complaint after a complete check using the XR25.NOTES
Check the calipers, drums and bearings are not seized.
Check that the tyres are not under inflated.
Check the coolingCheck that cooling is not insufficient.
Check the canister bleed
Disconnect the pipe connecting the canister bleed solenoid valve
to the inlet manifold.
Plug the pipe to prevent an air leak.
If there is no other effect, the canister bleed is faulty..
Check the axle assemblies
A
Connect the OPTIMA 5800 station to carry out the flywheel test
and follow the instructions.Check the flywheel
17-206

JSA052.0
INJECTION Fault finding - Aid
17
D7F 710
engine -
55 tracks
For further details, refer to section 12
Injector resistance = 14.5 Ω
Idle regulation stepping
motor resistance : A - D = 100 Ω
B - C = 100 Ω
Canister bleed valve resistance = 35 Ω
Ignition coil resistance : Primary = 1-4 ; 1-3 ; 2-3 ; 2-4 = 1.5 Ω
3-4 = 0.6 Ω
Secondary = 8 kΩ
Oxygen sensor heating resistance = 3 to 15 Ω
Throttle potentiometer resistance : no load A-B = 1300 Ωfull load A-B = 1300 Ω
A-C= 1360 ΩA-C= 2350 Ω
B-C = 2300 ΩB-C = 1260 Ω
Flywheel signal resistance = 220 Ω
Fuel pressure = 3 bars ignition on/ 2.5 bars at idle speed
Value for: CO = 0.3 % maximum
HC = 100 ppm maximum
CO2 = 14.5 % minimum
Oxygen = 0.97 < λ < 1.03
Sensor resistance
Temperature in °C 0 20 40 80 90
Air temperature sensor
Resistance in ohms5000
to
70001700
to
3300500
to
1550--
Coolant temperature sensor
Resistance in ohms6700
to
80002600
to
30001100
to
1300270
to
300200
to
215
17-207

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Engine cold, ignition on.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
1 Dialogue with XR25D13
(selector on
S8)
9.NJ
Use fiche n° 27
fault test side
2Interpretation of
normally illuminated
bargraphsFault test
Code present
3 ImmobiliserIf the vehicle does not have an
immobiliser, this bargraph
should be illuminated.
4 Change to status testG01*
10.NJ
Use fiche n° 27
status test side
1
1
2
17-208

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Engine cold, ignition on.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
5 Interpretation of
normally illuminated
bargraphsCode present
No load recognition
Illuminated if immobiliser
active
+ after ignition information
received
Locking relay control effective
Always illuminated if air
conditioning option available
Illuminates after erasing the
memory to indicate that the
operation has been carried out
correctly
Computer configured for:
Manual gearbox (G50*2*)
Automatic
transmission(G50*1*)
1
2
3
4
5
12
19
19
9
17-209

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Engine cold, ignition on.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
6 Throttle position
potentiometerNo load
# 17
Accelerator
pedal slightly
depressed
Full load
# 17 10 < X < 50
185 < X < 245
7Absolute pressure
sensor# 01 X = Local atmospheric
pressure
8Coolant temperature
sensor# 02 X = Ambient temperature
± 5 °C
9Air temperature
sensor# 03 X = Ambient temperature
± 5 °C
10Idle speed regulation
stepping motor# 12The value read is variable
depending on the coolant
temperature : : 11 % ≤ X ≤
100 %
11Engine speed
# 06 X = 0 rpm
12Canister bleed
# 23 X = 0.7 %
2
2
2
17-210

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
1 Change to status testG01*
10.NJ
Use fiche n° 27
status test side
2 No fault presentEnsure this bargraph is not
flashing, otherwise enter
G02* and turn over the fiche.
IMPORTANT: This bargraph
may flash if the vehicle has no
immobiliser. Ignore this
bargraph if fault bargraph 2 RH
side is illuminated and *22 = 2
dEF.
Repair the faulty component
the erase the memory (G0**)
and return to the status test
(G01*)
3 Battery voltage# 04
if in # 04
then # 06 13 volts < X < 14.5 volts
X < 12.7 volts
Engine speed < X < 880
rpm nominal
Engine warm, at idle speed, after fan assembly has operated at least once(air
conditioning not selected)NOTES
20
17-211

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Engine warm, at idle speed, after fan assembly has operated at least once(air
conditioning not selected)NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
4 Interpretation of
normally illuminated
bargraphs
-
Code present
No load recognition
Engine speed information
received
+ after ignition information
received
Locking relay control effective
Idle speed regulation active
Richness regulation active1
2
5
4
6
6
3
17-212

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Engine warm, at idle speed, after fan assembly has operated at least once (air
conditioning not selected)NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
4
(cont)Interpretation of
normally illuminated
bargraphs (cont)
-
Fuel pump active
Always illuminated if air
conditioning option available
Illuminates after erasing the
memory to indicate that the
operation has been carried out
correctly
Computer configured for:
Manual gearbox (G50*2*)
Automatic
transmission(G50*1*)
7
19
9
19
12
17-213