1997 RENAULT CLIO engine

Renault 1991
ENGINES (petrol)
4 cylinders - Cast-Iron
Types Vehicles
E5F Clio
E6J Extra
Clio
Renault 19
E7F Clio
Renault 19
E7J Extra
Clio
Renault 19
Mé
gane
77 11 193 633APRIL 1997Edition anglaise
."The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods ma
y be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories
from which his vehicles are constructed."All cop
yrights reserved by Renault.
Cop
ying or translating, in part or in full, of this document or use of the service partreference numbering system is forbidden without the prior written authority of
Renault
C
Cancels and replaces Part No. 77 11 091 458
Workshop Repair Manual
Page 1 of 1 E_Series_1
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_1.htm

Contents
Pages
ENGINE AND PERIPHERALS
- Foreword
- Section view
- En
gine identification
- Section and ti
ghtening torques
- Lubrication circuit dia
gram
-
S
pecifications
Standard exchan
ge
- S
pecial tooling required
- Essential e
quipment
- Engine repair
Ex
ploded view of cylinder head
Ex
ploded view of cylinder block
10-1
10-2
10-3
10-5
10-8
10-10
10-20
10-21
10-24
10-25
10-25
10-34
10
Page 1 of 1 E_Series_2
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_2.htm

ENGINE AND PERIPHERALS
Foreword
10
USE OF THE MANUAL
In this manual you will find three major chapters:
- specifications,
- removal of en
gine,
- reassembl
y of engine.
To repair a component on the vehicle refer to the
Workshop Repair Manual and Technical Notes.
UNITS OF MEASUREMENT
- All the dimensions are expressed in millimetres,
mm (unless otherwise indicated).
The tightening torques:
- in decaNewton metres daN.m
(reminder:
1 daN.m = 1.02 m.kg).
The tightening torques without tolerances
must be kept within
±10°.
- in degrees, the tightening torques without to-
lerances must be kept within
±3 %.
The pressures are in
bars.
10-1
Page 1 of 1 E_Series_3
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_3.htm

ENGINE AND PERIPHERALS
Section View
10
DI1042
10-2
Page 1 of 1 E_Series_4
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_4.htm

ENGINE AND PERIPHERALS
En
gine identification10
The engine is identified by a plate riveted onto
the cylinder block.
92072R
F GE D B A
0 0 0 0 0 0 0

0 0 0 0 0 / 0 0
It shows:
A: The engine type
B: The homologation lette
r
D: The identity of RENAULT SA
E: The engine suffix
G: The assembled engine factory reference
F: The engine fabrication numbe
r
10-3
Page 1 of 1 E_Series_5
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_5.htm

ENGINE AND PERIPHERALS
En
gine identification10
Engine Suffix VehicleCompression
ratioBore
(mm)
Stroke
(mm)
Capacity
(cm3)
E5F
710
716B/C/S 572
B 57N9.25/1
E7F
700
704
706
708
730
750B/C/S 57A
3/5 57F/L
B/C/S 57A
B/C/S 57R
B/C/S 57A
3/5 57G/R
B/C/L 53W
B/C 57S
3/5 57J9.25/1
9.25/1
8.8/1
9.5/1
9.25/1
9.5/1
E6J
700
701
706
712
713
718
734
738
760B/C/L/S537
B/C/L 537
B/L 536
B/C 57B
B/C 573
B 57P
F 40A
F 40Y
5 57B9.5/1
9.5/1
9.5/1
9.5/1
9.5/1
8.8/1
9.5/1
8.8/1
9.5/1
E7J
601
624
700
706
710
711
716
718
719
720
724
726
728
742
745
754
756
757
764
770
771
773B/C 57B
B A0T
B/C/L 53A
B/C/L 53A
B/C 57B
B/C 57B
B/C 57B
B/C 57T
B/C 57T
F 40V
F 40U
F 40U
F 40D
B/C/L 535
B/C/L 53A
B/C
57Y
B/C 57J
B/C 57J
B/J/L A0E
F 40S
F 40S
F 40U9.5/175.8 64.9 1171
75.8 139077
10-4
Page 1 of 1 E_Series_6
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_6.htm

ENGINE AND PERIPHERALS
Section and ti
ghtening torques(in daN.m and/or°)10
(1) Timing tension wheel nut: tighten to
5 daN.m
(2)
M6
bolt and nut: tighten to
1 daN.m
M8
bolt: tighten to
2.2 daN.m
(3) Pre-tighten to
2 daN.m, then angle tighten by
68°
±6°
DI1043
5 to 5.5
10-5
Page 1 of 1 E_Series_7
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_7.htm

ENGINE AND PERIPHERALS
Section and ti
ghtening torques(in daN.m and/or °)10
*
Pre-tighten the bolts to
2.5 daN.m, then angle tighten by
43°±6°
** See cylinder head tightening
DI1044
2.5 to 3
10-6
Page 1 of 1 E_Series_8
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_8.htm