1997 RENAULT CLIO diagram

ENGINE AND PERIPHERALS
S
pecifications10
* Since the Inlet Opening Retard is negative,
the opening of the valve is located after TDC.
** Since the Exhaust Closing Advance is negative,
the closing of the valve is located before TDC.
11953S
Timing diagram: (cannot be checked)
1 - Fixed mark TDC cylinder block
2 - Mobile mark flywheel TDC
3 - Mobile mark flywheel BDC
4 - Inlet Opening Retard (IOR)
5 - Exhaust Closing Advance (ECA)
6 - Inlet Closing Retard (ICR)
7 - Exhaust Opening Advance (EOA)
8 - Engine rotation direction (flywheel end) Inlet Opening Retard (IOR) * - 2 - 6 - 4
Inlet Closing Retard (ICR) 39 43 30
Exhaust Opening Advance (EOA) 48 44 40
Exhaust Closing Advance (ECA) ** - 7 - 3 - 6
E5F 710 - 716
E7F 700 - 704 - 706 -
730
E7J 624 -718 - 719 -
720
E6J 700 - 701 - 706 -
712 - 713 - 718 - 734
738 - 760
E7J 601- 700 - 706 -
710 - 711 - 716 - 724
726 - 728 - 742 - 745
754 - 756 - 757 - 764
770 - 771 - 773
E7F 708 - 750
10-14
Page 1 of 1 E_Series_16
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_16.htm

ENGINE AND PERIPHERALS
En
gine repair10
- the distributor with the wiring loom,
- the fuel pump (if fitted) with new seals,
- the thermostat support, making it tight with
Loctite 518.
The bead (H) should be
0.6 to 1 mm wide and
should be applied as shown in the diagram be-
low,
- the seal, using mounting bush
Mot. 1127-01;
this tool is designed to obtain an offset seat fo
r
the seal,
92102S92066R
Lubricate the camshaft.
Refit the camshaft and its flange.
Check:
- the end play which should be between
0.06 and
0.015 mm; if this is not the case, the flange o
r
the camshaft are to blame,
92102-1R
- the camshaft sprocket, immobilising it with tool
Mot. 799-01, and tighten the bolt to a torque
value of
4.5 daN.m (lubricate the thread an
d
underneath the bolt head).
10-33
Page 1 of 1 E_Series_35
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_35.htm

ENGINE AND PERIPHERALS
En
gine repair10
Fit:
- the oil pump, checking that the centring dowls
are present, and tighten to a torque value of
2.5 daN.m,
- the two sprockets and chain of the oil pump,
and tighten the three bolts mounting the
sprocket to the hub to
1 daN.m,
- the crankshaft end cover, sealing it with
Loctite
518.
The bead (H) should be
0.6 to 1 mm wide and
should be applied as shown in the diagram be-
low. - the crankshaft seal (bearing No.1), using tool
Mot. 1129-01; this tool is designed to ensure an
offset seal bearing surface. Lubricate the lip
and the outside of the seal.
92319R
92067R
-the crankshaft end seal, using tool
Mot. 1128-
01; lubricate the lip and the outside diamete
r
of the seal.
Turn over the s
pacer if the old seal has marked
the bearin
g surface.
92318R
10-43
Page 1 of 1 E_Series_45
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_45.htm

ENGINE AND PERIPHERALS
En
gine repair10
99179R1
Refit the sump and tighten to a torque value of
1 daN.m.
NOTE : A tight seal for the sump can only be ob-
tained using the special seal supplied by the afte
r-
sales service, except for engine
E7J 764 in which a
tight seal is achieved by using
RHODOR-SEAL
5661. Bead (D) should be
3 mm wide.
Do not forget to replace the two "half-moon"
seals at (A) with new ones.
Coat the flywheel bearing surface on the cranks-
haft with
AUTOFORM Loctite.
Fit the flywheel or the converter plate and immo-
bilise it with the toothed segment
Mot. 582-01.
Apply a drop of
FRENETANCH Loctite to the
bolts and tighten them to
5 - 5.5 daN.m.
Centre the clutch disc and secure the mechanism.
92068R
Refit the water pump, sealing it with
Loctite 518.
The bead (H) should be
0.6 to 1 mm wide and
should be applied as shown in the diagram below.
REFITTING THE CYLINDER HEAD
Remove the liner tool
Mot. 588.
Clean the gasket surfaces of the cylinder bloc
k
and the cylinder head.
Refit the cylinder head centring dowl.
The new cylinder head gasket.
The cylinder head (lubricate the threads and
underneath the bolt heads).
All the cylinder head bolts must be replaced
systematically after any removal.
10-44
Page 1 of 1 E_Series_46
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_46.htm