1997 MITSUBISHI TRITON engine coolant

MPI ± Troubleshooting13A-52
INSPECTION PROCEDURE 41
MUT-II: Check if surge occurs.
MUT-II Data list
26 Idle position switch (Refer to P.13A-57.)NGCheck the idle position switch system.
(Refer to P.13A-40, INSPECTION PROCEDURE 25.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13A-57.)NGCheck the intake air sensor system. (Refer to P.13A-12, INSPEC-
TION PROCEDURE FOR DIAGNOSIS CODE 13.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13A-57.)NGCheck the barometric pressure sensor system. (Refer to P.13A-18,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13A-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13A-14, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
14 Throttle position sensor (Refer to P.13A-57.)NGCheck the throttle position sensor system. (Refer to P.13A-13, IN-
SPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)
OK
MUT-II Actuator test
10 EGR control solenoid valve (Refer to P.13A-62.)NGCheck the EGR control solenoid valve system.
(Refer to P.s13A-46, INSPECTION PROCEDURE 33.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 600 ± 1,000 mV during sudden racingNGCheck the oxygen sensor system. (Refer to P.13A-11, INSPECTION
PROCEDURE FOR DIAGNOSIS CODE 11.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Changes between 0 ± 400 mV and 600 ± 1,000 mV during
idlingNGCheck the fuel pressure.
(Refer to P.13A-81.)OK1. Inspect the intake of
air into the air intake
system

Broken intake
manifold gasket

Broken vacuum
hose

PCV valve does
not operate.

Broken air intake
hose
2. Check the injector for
clog.

MPI ± Troubleshooting13A-57
DATA LIST REFERENCE TABLE13100890180
Caution
When shifting the select lever to D range, the brakes should be applied so that the vehicle does
not move forward.
NOTE
*1. In a new vehicle [driven approximately 500 km or less], the air flow sensor output frequency is sometimes
10% higher than the standard frequency.
*
2. The idle position switch normally turns off when the voltage of the throttle position sensor is 50 ±
100 mV higher than the voltage at the idle position. If the idle position switch turns back on after
the throttle position sensor voltage has been by 100 mV and the throttle valve has been opened,
the idle position switch and the throttle position sensor need to be adjusted.
*3. The injector drive time represents the time when the cranking speed is at 250 r/min or below when
the power supply voltage is 11 V.
*4. In a new vehicle [driven approximately 500 km or less], the injector drive time is sometimes 10%
longer than the standard time.
*5. In a new vehicle [driven approximately 500 km or less], the step of the stepper motor is sometimes
30 steps greater than the standard value.
Item
No.Inspection
itemInspection contentsNormal conditionInspection
procedure
No.Reference
page
11Oxygen
sensorEngine:After having
warmed up
Air/fuel mixture is
made leaner when de-
When at 4,000 r/min,
engine is suddenly
decelerated200 mV or lessCode No.
1113A-11
made leaner when de-
celerating, and is made
richer when racing.
When engine is
suddenly raced600 ± 1,000 mV
Engine:After having
warmed up
The oxygen sensor
signal is used to check
the air/fuel mixture
ratio and control
Engine is idling400 mV or less
(Changes)
600 ± 1,000 mV
ratio, and control
condition by the en-
gine-ECU.2,500 r/min400 mV or less
(Changes)
600 ± 1,000 mV
12Air flow
sensor*1
Engine coolant
temperature:
80 ± 95C

Lamps and all
accessories: OFF
Engine is idling22 ± 48 Hz
<4G63>
19 ± 45 Hz
<4G64>±±
accessories: OFF

Transmission:
Neutral (A/T:
P range)2,500 r/min80 ± 120 Hz
<4G63>
67 ± 107 Hz
<4G64>
Engine is racedFrequency
increases in
response to
racing

MPI ± Troubleshooting13A-58
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
13Intake air
temperature
sensor
Ignition switch: ON or
with engine runningWhen intake air
temperature is ±20
C±20
CCode No.
1313A-12
sensorWhen intake air
temperature is 0
C0
C
When intake air
temperature is 20
C20
C
When intake air
temperature is 40
C40
C
When intake air
temperature is 80
C80
C
14Throttle
p
osition
Ignition switch: ONSet to idle position300 ± 1,000 mVCode No.
14
13A-13
osition
sensorGradually openIncreases in
proportion to
throttle opening
angle
14
Open fully4,500 ± 5,500 mV
16Power
supply
voltageIgnition switch: ONSystem voltageProcedure
No. 2313A-39
18Cranking
signal
(ignition
it h ST)
Ignition switch: ONEngine: StoppedOFFProcedure
No. 26
13A-41

13A-42
switch-ST)Engine: CrankingONProcedure
No. 27

21Engine
coolant
temperature
sensor
Ignition switch: ON or
with engine runningWhen engine
coolant temperature
is ±20
C±20
CCode No.
2113A-14
sensor
When engine
coolant temperature
is 0
C0
C
When engine
coolant temperature
is 20
C20
C
When engine
coolant temperature
is 40
C40
C
When engine
coolant temperature
is 80
C80
C

MPI ± Troubleshooting13A-59
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
22Crank angle
sensor
Engine: Cranking

Tachometer:
ConnectedCompare the engine
speed readings on
the tachometer and
the MUT-II.AccordCode No.
2213A-15

Engine: Idling

Idle position
switch: ONWhen engine
coolant temperature
is ±20C1,275 ± 1,475 r/min
When engine
coolant temperature
is 0C1,225 ± 1,425 r/min
When engine
coolant temperature
is 20C1,100 ± 1,300 r/min
When engine
coolant temperature
is 40C950 ± 1,150 r/min
When engine
coolant temperature
is 80C650 ± 850 r/min
25Barometric
p
ressure
Ignition switch: ONAt altitude of 0 m101 kPaCode No.
25
13A-18
ressure
sensorAt altitude of 600 m95 kPa
25
At altitude of 1,200 m88 kPa
At altitude of 1,800 m81 kPa
26Idle position
switchIgnition switch: ON
Check by operating
acceleratorpedal
Throttle valve:
Set to idle positionONProcedure
No. 2513A-40
accelerator pedal
repeatedlyThrottle valve:
Slightly openOFF*2
27Power
steering fluid
p
ressure
Engine: IdlingSteering wheel
stationaryOFFProcedure
No. 2813A-43
pressure
switchSteering wheel
turningON

MPI ± Troubleshooting13A-60
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
28A/C switchEngine: Idling
(when A/C switch isA/C switch: OFFOFFProcedure
No. 2913A-43
(
ON, A/C compressor
should be operating.)A/C switch: ONON
29Inhibitor
switch
Ignition switch: ONP or NP or NProcedure
No 27
13A-42
switch
D, 2, L or RD, 2, L or R
No. 27
41Injectors *3Engine: CrankingWhen engine cool-
ant temperature is
0C51 ± 76 ms
<4G63>
60 ± 90 ms
<4G64>±±
When engine
coolant temperature
is 20C26 ± 38 ms
<4G63>
30 ± 45 ms
<4G64>
When engine
coolant temperature
is 80C5.7 ± 8.5 ms
<4G63>
6.7 ± 10.1 ms
<4G64>
Injectors*4
Engine coolant
temperature:
80 ± 95C

Lamps and all
accessories: OFF
Engine is idling1.9 ± 3.1 ms
<4G63>
2.2 ± 3.4 ms
<4G64>
accessories: OFF

Transmission:
Neutral (A/T :
P range)2,500 r/min1.8 ± 3.0 ms
<4G63>
1.9 ± 3.1 ms
<4G64>
When engine is
suddenly racedIncreases
44Ignition coils
and power
Engine: After
having warmed upEngine is idling2±18BTDC±±
transistors
g

Timing lamp is set.
(The timing lamp
is set in order to
check actual
ignition timing.)2,500 r/min23 ± 43 BTDC
<4G63>
27 ± 47 BTDC
<4G64>

MPI ± Troubleshooting13A-61
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
45ISC
(stepper)
motor
p
osition*5

Engine coolant
temperature:
80 ± 95C

Lamps and all
A/C switch: OFF2 ± 25 STEP±±
osition 5
Lam s and all
accessories: OFF

Transmission:
Neutral (A/T :
P range)

Idleposition
A/C switch:
OFF
ONIncreases by
10 ± 70 steps

Idle osition
switch: ON

Engine: Idling

When A/C switch
is ON, A/C
compressor should
be operating
A/C switch: OFF

Select lever:
N range
D
rangeIncreases by
5 ± 50 steps
49A/C relayEngine: After having
warmed up/Engine is
idlingA/C switch: OFFOFF (Compressor
clutch is not
operating)Procedure
No. 2913A-43
A/C switch: ONON (Compressor
clutch is
operating)

MPI ± TroubleshootingMPI ± Troubleshooting13A-66
Terminal No.Normal condition Check condition (Engine condition) Check item
63Engine coolant
temperature sensorIgnition switch:
ONWhen engine
coolant tempera-
ture is 0C3.2 ± 3.8V
When engine
coolant tempera-
ture is 20C2.3 ± 2.9V
When engine
coolant tempera-
ture is 40C1.3 ± 1.9V
When engine
coolant tempera-
ture is 80C0.3 ± 0.9V
64Throttle position
sensorIgnition switch:
ONSet throttle valve
to idle position0.3 ± 1.0V
Fully open throttle
valve4.5 ± 5.5V
65Barometric pressure
sensorIgnition switch:
ONWhen altitude is
0m3.7 ± 4.3V
When altitude is
1,200m3.2 ± 3.8V
66Vehicle speed sensor
Ignition switch: ON

Move the vehicle slowly forward0
5V
(Changes repeatedly)
67Idle position switchIgnition switch:
ONSet throttle valve
to idle position0±1V
Slightly open
throttle valve4V or more
68Top dead centre sensorEngine: Cranking0.4 ± 3.0V
Engine: Idle speed0.5 ± 2.0V
69Crank angle sensorEngine: Cranking0.4 ± 4.0V
Engine: Idle speed1.5 ± 2.5V
70Air flow sensorEngine: Idle speed2.2 ± 3.2V
Engine r/min: 2,500r/min
71Inhibitor switch Ignition switch:
ONSet selector lever
to P or N0±3V
Set selector lever
to Other than P or
N8 ± 14V

MPI ± Troubleshooting13A-68
Terminal No. Normal condition (Check condition)Inspection item
4±12Stepper motor coil (A1)28 ± 33 W (At 20
C)
17 ± 12Stepper motor coil (A2)
5±12Stepper motor coil (B1)
18 ± 12Stepper motor coil (B2)
6±12EGR control solenoid valve36 ± 44 W (At 20
C)
9±12Purge control solenoid valve36 ± 44 W (At 20
C)
13 ± Body earthEngine-ECU earthContinuity (0W)
26 ±Body earthEngine-ECU earth
35 ± 12Oxygen sensor heaterApprox. 12 W (At 20
C)
52 ± 72Intake air temperature sensor5.3 ± 6.7 kW (When intake air temperature is 0
C)
2.3 ± 3.0 kW (When intake air temperature is 20
C)
1.0 ± 1.5 kW (When intake air temperature is 40
C)
0.30 ± 0.42 kW (When intake air temperature is 80
C)
63 ± 72Engine coolant temperature sensor5.1 ± 6.5 kW (When coolant temperature is 0
C)
2.1 ± 2.7 kW (When coolant temperature is 20
C)
0.9 ± 1.3 kW (When coolant temperature is 40
C)
0.26 ± 0.36 kW (When coolant temperature is 80
C)
67 ± 72Idle position switchContinuity (when throttle valve is at idle position)
No continuity (when throttle valve is slightly open)
71 ±Body earthInhibitor switch Continuity (when select lever is at P or N)
No continuity (when select lever is at D, 2, L or R)