AUTOMATIC TRANSMISSION ± On-vehicle Service23-19
CONVERTER STALL TEST 23100540138
In this test, the engine maximum speed when the
torque converter stalls with the shift lever in the
ªDº or ªRº range is measured to check operation
of the torque converter, starter and one-way clutch
and check holding performance of the transmission
clutch (including brake).
Caution
Do not stand in front or at rear of the vehicle
during this test.
(1) Check the transmission fluid level. The fluid
temperature should be at the level after normal
operation (70 ± 80C). The engine coolant
temperature should also be at the level after
normal operation (80 ± 90C).
(2) Apply chocks to the rear wheels (right and left).
(3) Mount an engine tachometer.
(4) Apply fully the parking and service brakes.(5) Start the engine.
(6) With the selector lever in the ªDº range, fully
depress the accelerator pedal and read off the
engine maximum speed.
Standard value:
2,100 ± 2,400 r/min <4G63>
2,300 ± 2,600 r/min <4D56>
NOTE
When doing so, do not keep the engine running
with throttle full open for more than 5 seconds.
If two or more stall tests are needed, place
the selector lever in the ªNº position and run
the engine at about 1,000 r/min to allow the
transmission fluid to cool before another stall
test.
(7) Place the selector lever in the ªRº range and
perform the test as above.
JUDGEMENT OF STALL TEST RESULTS
Stall speed in ªDº and ªRº range is equal to each other
but lower than the nominal value.(1) Engine output is low.
(2) Starter one-way clutch is faulty. (Faulty torque
converter is suspected if it is lower than nominal
by more than 600 r/min)
Stall speed in ªDº range is higher than nominal.(1) Overdrive clutch slipping
(2) Overdrive one-way clutch faulty
(3) Forward clutch slipping
(4) One-way clutch No. 2 faulty
(5) Low line pressure
Stall speed in ªRº range is higher than nominal.(1) Overdrive clutch slipping
(2) Overdrive one-way clutch faulty
(3) Direct clutch slipping
(4) Brake No. 3 slipping
(5) Low line pressure
ABS <4WD> ± Troubleshooting35C-8
Code No. 26 4WD position detection switchProbable cause
This code is output at the following times:
ABS-ECU determines that an open circuit exists in the 4WD detection switch system.
The free wheel engage switch is off and the 4WD detection switch is on at a vehicle
speed of 15km/h or more for 5 seconds or more.Malfunction of wiring harness or connector
Malfunction of free wheel engage switch
Malfunction of 4WD indicator-ECU
Malfunction of 4WD position detection switch
Malfunction of ABS-ECU
No
OK
Check trouble symptom.NGCheck the harnesses between 4WD
position detection switch and the ABS-
ECU, and repair if necessary.
OKCheck the following connector.
C-64NG
Repair
OK
Check trouble symptom.NGReplace the ABS-ECU.
Ye s
Measure at ABS-ECU connec-
tor C-64.
Disconnect the connector
and measure at the harness
side.
Ignition switch ON
Transfer lever:2H
Voltage between 35 and
body earth
OK:System voltageNGCheck the following connector.
C-64NG
Repair
Does the 4WD indicator lamp operate
normally?
Trouble symptomMain causeRemedy
Even when the transfer shift lever is
in the º4Hº position, the 4WD front
wheel indicator lamp does not
illuminate.Broken harness wire between the 4WD
indicator-ECU and the free-wheel
engage switch, or broken earth wire
from the free wheel engage switchRepair the harness.
Free wheel engage switch is defective.Replace the switch.
Even when the transfer shift lever is
in the º4Hº position, the free wheel
differential indicator lamp does not
illuminate
Broken harness wire between the 4WD
indicator-ECU and the 4WD position
detection switchRepair the harness.
illuminate.Broken wire in the 4WD indicator-ECU
circuit4WD indicator-ECU inspection (Re-
fer to GROUP 22 ± 4WD indicator-
ECU.)
Free wheel differential indicator
lamp illuminates regardless of the
p
osition of the transfer shift lever
Short in the harness wire in the 4WD
position detection switch circuitRepair the harness.
position of the transfer shift lever.4WD position detection switch is
defective.Replace the switch.
Short in the ABS-ECU circuitReplace the ABS-ECU.
Short in the 4WD indicator-ECU circuit4WD indicator-ECU inspection (Re-
fer to GROUP 22 ± 4WD indicator-
ECU.)
No indicator is illuminatedPower circuit in the 4WD indicator-ECU
is defective.Repair the harness.
4WD indicator-ECU is defective.4WD indicator-ECU inspection (Re-
fer to GROUP 22 ± 4WD indicator-
ECU.)
NOTE
When checking a short in the ABS-ECU circuit, remove the ABS-ECU connector and check if the 4WD
indicator returns to normal. If it returns to normal, the ABS-ECU is defective. Furthermore, if the ABS-ECU
is normal, then the 4WD indicator-ECU will be defective.
