1997 LINCOLN TOWN CAR jump start

58When in AUTOMATIC and weather conditions
require heat, air will be sent to the floor. But, a
feature is included in your EATC to prevent
blowing cold air to the floor if the engine coolant is
not warm enough to allow heating. For a short
time the fan will be at low speed and air directed
to the windshield. In 3-1/2 minutes or less, the fan
speed will start to increase and the airflow will
change to the floor area.
If unusual conditions exist (i.e., window fogging,
etc.), the six manual override buttons allow you to
select special air discharge locations. A thumbwheel
allows you to adjust the fan speed to suit your
needs.
Temperature selectionThe RED and BLUE buttons at the upper left of the
Control are for temperature selection. The RED
button will increase the set temperature and the
BLUE button will lower the set temperature.
Pressing a button and releasing it will change the
set temperature one degree. Holding either button
in will rapidly change the temperature setting in
one degree increments to either65ÊF(18ÊC)
(BLUE) or85ÊF(29ÊC)(RED).Then, the set
temperature will jump 5 Ê and stop at either60ÊF
(16ÊC)which is maximum cooling or90ÊF(32ÊC)
which is maximum heating.
The average temperature range used is between
68ÊF(20ÊC) and78ÊF(26ÊC).Changing the
temperature setting by several degrees outside this
range or overriding to60ÊF(16ÊC) or90ÊF(32ÊC)
will not speed up the heating or cooling process.
File:05fncft.ex
Update:Mon Jun 17 13:49:49 1996

205
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water for
at least 15 minutes. If someone swallows the acid,
have him or her drink lots of milk or water first,
then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to jump-start
and connecting the jumper cables in the order they
are given. If in doubt, call for road service.Preparing Your Vehicle1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system. You
will damage your starting motor, ignition
system, and other electrical parts if you connect
them to a 24-volt power supply (either two
12-volt batteries in series or a 24-volt generator
set).2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
5. Turn on the heater fan in both vehicles. Press
the DEFROST button. Turn off all other
switches and gauges.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

208Jump-Starting1. Make sure that the jumper cables are not in
the way of moving engine parts, then start the
booster vehicle. Run the engine at a moderate
speed.
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle. It
may take a couple of tries before the vehicle
starts. If the vehicle does not start after several
attempts, there may be a different problem.
3. When both vehicles are running, let them idle
for a few minutes to charge the discharged
battery.Removing jumper cables1.Always remove the jumper cables in the
reverse order.Remove the negative (s) end
of the jumper cable from the metallic surface
on the engine or frame of the disabled vehicle.2. Remove the negative (s) cable from the
booster battery.
3. Remove the positive (+) cable from the booster
battery.
4. Remove the other end of the positive (+) cable
from the discharged battery.
After the vehicle is started, let it idle for a while to
let the engine ªrelearnº its idle conditions. Drive it
around for a while with all electrical accessories
turned off to let the battery recharge. Driveability
may be deteriorated slightly until all drive modes
are ªrelearned.ºYou may need to use a battery
charger to fully recharge the battery.
If you need to replace your battery, seeBatteryin
theMaintenance and Carechapter.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

300Driving under special conditions
heavy load............. 177
towing a trailer........... 179
E
Electrical system
circuit breakers........... 191
fuses................ 190
power point outlet.......... 73
Electronic sound system
antenna............... 40
tuning the radio........... 36
warranty and service information.... 53
Electronic stereo cassette radio
(see Electronic sound system)..... 35
Electronic stereo radio (see Electronic
sound system)............ 35
Emergencies, roadside
fuel................ 243
jump-starting............ 204
towing............... 209Emergency brake (parking brake)..... 168
Emission control system......... 246
catalytic converter.......... 246
emissions warranty........ 3,246
Engine
check engine warning light...... 14
does not start.........163, 181
fuel injected engine, starting...... 161
fuel pump shut-off switch....... 181
preparing to start........... 161
refill capacities............ 258
service points............ 216
starting............... 162
starting after a collision........ 181
storing your vehicle......... 260
Engine block heater........... 164
File:fnixt.ex
Update:Mon Jun 17 13:58:01 1996

304High beams (continued)
operation.............. 76
Hood................. 215
latch location............ 215
lubrication specifications....... 259
release lever............. 215
working under the hood....... 213
Horn................. 79
I
Idle, relearning..........208, 213
Ignition
chime............... 75
positions of the ignition........ 73
removing the key.......... 75
Infant seats (see Safety seats)....... 141
Instrument cluster, electronic....... 9
Instrument panel............. 7
Interval wipers............. 77
J
Jack.................. 193
operation.............. 196
positioning............. 196
storage............... 193
Jump-starting your vehicle
attaching cables........... 206
disconnecting cables......... 208
K
Keyless entry system
locking and unlocking doors...... 107
programming entry code....... 109
Keys
key in ignition chime......... 75
positions of the ignition........ 73
removing from the ignition...... 75
stuck in lock position......... 75
File:fnixt.ex
Update:Mon Jun 17 13:58:01 1996