1997 LINCOLN MARK VIII high beam

14Turn Signal Indicator LightsWhen you push the turn signal lever up before
making a right turn, the right side arrow on the
instrument panel flashes.
When you push the turn signal lever down before
making a left turn, the left side arrow on the
instrument panel flashes.
Usually, the turn signals turn off automatically after
you turn your vehicle. If the turn signal continues
to flash after you have made the turn, push the
lever back to the OFF position.
If one or both of your turn indicators do not flash
or stay on continuously, have them serviced as soon
as possible. In the meantime, be sure to use the
accepted hand signals.High Beam LightThis light illuminates when the headlamps are
turned to high beam or when you flash the lights.
File:03fnis8.ex
Update:Thu Jun 27 10:00:37 1996

35
CHECK TRANS-MISSIONÐ This warning
message is displayed when the transmission is not
operating properly. If this warning stays on or
comes on, contact your dealer for transmission
service as soon as safely possible.
TRANS-MISSION OVERHEATÐ This warning
message is displayed when the transmission is
overheating. This warning may appear when towing
heavy loads, or driving in a low gear at high speed
for an extended period of time. Stop the vehicle as
soon as safely possible, turn off the engine and let it
cool. Check the transmission fluid and level
following the instructions in theMaintenance and
Carechapter. If this warning stays on or continues
to come on, contact your dealer for transmission
service as soon as safely possible.CHECK BRAKE LAMPSÐ This warning message
is displayed when you turn on the brake lamps and
at least one of them is burned out. Check the
lamps as soon as safely possible, and have the
burned out lamp replaced following the instructions
in theMaintenance and Carechapter. Note the
center high mounted stop lamp is not monitored.
CHECK HEADLAMPSÐ This warning message is
displayed when you turn on the headlamps and at
least one of them is burned out. Check the lamps
as soon as safely possible, and have the burned out
lamp replaced following the instructions in the
Maintenance and Carechapter. Note the high
beam lamps are not monitored.
CHECK TAIL LAMPSÐ This warning message is
displayed when you turn on the tail lamps and at
least one of them is burned out. Check the lamps
as soon as safely possible, and have the burned out
lamp replaced following the instructions in the
Maintenance and Carechapter.
File:03fnis8.ex
Update:Thu Jun 27 10:00:37 1996

86For lane changes, move the lever far enough to
signal but not to latch. The lever will return to the
off position when you release it.
When the turn signal is used when the headlamps
are on, the cornering lamps will automatically light
on either the right or left side depending on the
direction of the turn.High BeamsTo turn on the high beams, turn the headlamp
control switch to the headlamp ON position (or
activate the autolamp feature) and pull the turn
signal lever toward you until it latches. When the
high beams are ON, the high beam indicator light
on the instrument cluster comes on.
To turn off the high beams, push the lever away
from you until it latches. The high beam indicator
light turns off.NOTE:When the headlamps are on low beam, the
outer two headlamps are on. When the headlamps
are on high beam, the two outer headlamps will
turn off and the inner headlamps turn on.
Flashing the LightsTo flash the headlamps, pull the lever toward you
for a moment and then release it. The headlamps
will flash whether the headlamp knob is in the on
or off position.Windshield Wipers and WasherThe wiper system is controlled by the windshield
wiper control module. The windshield wiper will
operate with the ignition switch in the ACC or ON
position or in the delayed accessory mode. The
wiper system functions are as follows:
INTERMITTENTÐ Wipers run at low speed at
intervals set by rotating the barrel of the wiper
switch. The interval can be adjusted between one
to twenty seconds.
File:05fncf8.ex
Update:Thu Jun 27 10:02:20 1996

255
Headlamp bulb removalRemoving the high beam headlamp bulb1. Make sure that the headlamp switch is in the
OFF position.
2. Lift the hood, remove the sight shield above
the headlamp and find the bulb in the
headlamp socket.3. Remove the high beam dust cap by rotating
counterclockwise 1/4 turn. Pull back to
exposes wiring and connector.
4. Remove the bulb connector by pulling rearward
to free it from the lamp assembly.
5. Remove the electrical connector by pulling off
the bulb base.
Installing the high beam headlamp bulb1. Push the electrical connector into the rear of
the plastic base of the bulb until it snaps,
locking it into position.
2. Insert the glass envelope of the bulb into the
lamp assembly socket while aligning the locking
tabs.
3. Rotate the bulb 1/4 turn to lock.
File:11fnmc8.ex
Update:Thu Jun 20 14:28:32 1996

2564. Replace the high beam dust cap by aligning
tabs and rotating clockwise 1/4 turn.
5. Replace the sight shield.Aiming HeadlampsYour vehicle is equipped with a Vehicle Headlamp
Aim Device (VHAD) on each headlamp body. Each
headlamp may be properly aimed in the horizontal
direction (left/right) and the vertical position
(up/down).
NOTE:A non-zero bubble reading does not
necessarily indicate out-of-aim headlamps. If your
vehicle is not positioned on a level surface, the
slope will be included in the level indicator.
Therefore, vertical headlamp adjustment should be
performed only when beam direction appears to be
incorrect or a level surface can be verified.Tools required: One 6mm socket and ratchet.
The Horizontal aim must be adjusted first.
NOTE:The following procedure assumes that the
vehicle's front structure is in factory alignment
condition. If the vehicle has been in an accident
requiring the front end of the vehicle to be
repaired, the horizontal indicator should be
recalibrated by the servicing facility.
File:11fnmc8.ex
Update:Thu Jun 20 14:28:32 1996

297
Brakes
adjustment............. 171
anti-lock.............. 171
anti-lock brake system (ABS)
warning light........... 11
applying the brakes.......... 171
brake warning light.......... 10
fluid, checking and adding....... 225
fluid, refill capacities......225, 264
fluid, specifications.......... 265
front disc.............. 171
if brakes do not grip well....... 171
master cylinder........... 225
new brake linings........... 5
noise................ 171
parking brake and auto-release..... 172
servicing.............. 225
trailer............... 187
when storing your vehicle....... 268Break-in period.............. 5
Brights (high beams).......... 14
Bulbs, replacing............ 253
halogen............... 254
headlamps.............. 254
C
Canada, customer assistance....... 276
Canada, warranty information....... 3
Canadian Motor Vehicle Arbitration Plan
(CAMVAP).............. 277
Capacities for refilling fluids....... 264
Carbon monoxide in exhaust....... 169
Car seats for children
(see Child safety seats)........ 151
Catalytic converter........... 250
File:fnix8.ex
Update:Thu Jun 27 10:02:38 1996

304Headlamps (continued)
flashing............... 86
high beam............. 86
replacing bulbs........... 253
turning on and off.......... 79
warning chime............ 15
Head restraints............. 131
Heated seats.............. 135
Heating
electronic automatic temperature
control system........... 69
High beams
indicator light............ 14
operation.............. 86
Hitch................. 186
Hood................. 219
latch location............ 219
lubrication specifications....... 265
release lever............. 219
working under the hood....... 217
Horn................. 90
I
Idle, relearning..........212, 217
Ignition
chime............... 84
positions of the ignition........ 83
removing the key.......... 84
Indicator lights and chimes (see Lights) . . . 7
Infant seats (see Safety seats)....150, 151
Instrument panel............. 7
Interval wipers............. 86
J
Jack.................. 202
operation.............. 203
positioning............. 205
storage............... 202
Jump-starting your vehicle
attaching cables........... 211
disconnecting cables......... 212
File:fnix8.ex
Update:Thu Jun 27 10:02:38 1996

305
K
Keyless entry system
locking and unlocking doors...... 119
programming entry code....... 120
Keys
key in ignition chime......... 84
positions of the ignition........ 83
removing from the ignition...... 84
stuck in lock position......... 83
L
Lamps
autolamp delay system........ 80
checking.............. 253
daytime running light system..... 78
dome lamps............. 96
flashing the lamps.......... 86
hazard flashers............ 89
headlamps............. 79
high beams............. 86
interior lamps............ 78map lamps............. 96
replacing bulbs............ 253
trailer............... 187
Lane change indicator (see Turn signal) . . 85
Lap belts............... 143
Lights, warning and indicator
airbag............... 45
anti-lock brakes (ABS)......... 11
brake................ 10
charging system........... 13
check engine............ 45
engine oil pressure.......... 11
hazard warning light......... 89
high beam............. 14
overdrive off............. 46
safety belt.............. 44
turn signal indicator......... 14
File:fnix8.ex
Update:Thu Jun 27 10:02:38 1996