1997 ISUZU TFS SERIES lock

5-64 BRAKES
PARKING BRAKE (FLOOR MOUNT TYPE)
REMOVAL AND INSTALLATION
PARKING BRAKE LEVER AND FRONT CABLE ASSEMBLY
Removal Steps
1. Lock nut
2. Adjust nut
3. Equalizer
4. Center console
5. Bolt
6. Switch connector
7. Parking brake lever
8. Parking brake front cable
Installation Steps
8. Parking brake front cable
7. Parking brake lever
6. Switch connector
5. Bolt
4. Center console
3. Equalizer
2. Adjust nut
1. Lock nut
Important Operation - Installation
8. Parking Brake Front Cable
Apply grease (BESCO L-2 or equivalent) to the front cable
before installation.
After installation, be sure to adjust the parking brake.
Refer to "SERVICING" of this section.

BRAKES 5-65
REAR CABLE ASSEMBLY
Removal Steps
1. Lock nut
2. Adjusting nut
3. Bolt
4. Retainer
5. Clip and bolt ; crossmember
6. Clip and bolt ; side member
7. Clip and bolt ; side member
8. Clip and bolt ; spring eye
9. Clip and bolt ; leaf spring
10. Hand brake rear cable
Installation Steps
10. Hand brake rear cable
9. Clip and bolt ; leaf spring
8. Clip and bolt ; spring eye
7. Clip and bolt ; side member
6. Clip and bolt ; side member
5. Clip and bolt ; crossmember
4. Retainer
3. Bolt
2. Adjusting nut
1. Lock nut

5-66 BRAKES
Important Operations - Removal
Preparation
Raise vehicle to the working level.
Support the axle assembly with the proper jack and chassis
stands.
Remove the tire and wheel.
Remove the brake drum.
1. Lock Nut
2. Adjusting Nut
3. Bolt
4. Retainer
Loosen lock nut and adjusting nut, then disconnect rear
cable from the equalizer.
Remove bolt and retainer.
Important Operations - Installation
10.Hand Brake Rear Cable
Apply grease (BESCO L-2 or equivalent) to the
circumference of the pin and joint.
Apply grease (BESCO L-2 or equivalent) to the equalizer
joint portion.
9. Clip and Bolt; Leaf Spring
8. Clip and Bolt; Spring Eye
7. Clip and Bolt; Side Member
6. Clip and Bolt; Side Member
5. Clip and Bolt; Crossmember
Torque N
m (kgfm/lbft)
6 (0.6 / 4.3)
4. Retainer
3. Bolt
Torque N
m(kgfm/lbft)
16 (0.6 / 4.3)
2. Adjusting Nut
1. Lock Nut
Apply grease (BESCO L-2 or equivalent) to the front cable
contact portion.
Connect rear cable to the equalizer, then adjust the parking
brake. Refer to "SERVICING".
Tighten lock nut to the specified torque.
Torque N
m(kgfm/lbft)
16 (0.6 / 4.3)

10-2 CAB
SERVICING
Engine Hood Lock
Align the engine hood lock with the installation holes.
Engine Hood Striker
Apply a light coat of grease to the striker.
Door Checker Arm and Pin
Apply a light coat of grease to the checker arm and pin.

10-8 CAB
SLIDING REAR WINDOW ASSEMBLY
DISASSEMBLY
Disassembly Steps
1. Weather strip
2. Packing ; rear window
3. Screw; binding
4. Frame ; rear window
5. Stopper
6. Rear window ; slide
7. Lock assembly with catchback window
8. Glass run
9. Glass ; rear window corner
10. Weather strip ; rear window corner

10-10 CAB
REASSEMBLY
Riassembly Steps
1. Weather strip ; rear window corner
2. Glass ; rear window corner
3. Glass run
4. Frame ; rear window
5. Screw; binding
6. Rear window ; slide
7. Stopper
8. Packing ; rear window
9. Lock assembly with catchback window
10. Weather strip

10-14 CAB
3. Lower Hinge
Position a wood block under the door for protection and
support the door assembly with hands at removal or
installation.

CAB 10-15
DISASSEMBLY
(Front Door)
87 910
11 6
Disassembly Steps
1. Power window switch/Windows regulator
handle
2. Bezel
3. Speaker grill
4. Speaker assembly
5. Door pull case
6. Door mirror cover/Tweeter
7. Door trim pad
8. Door pocket
9. Power window box
10. Inner waste seal
11. Outer waste seal
12. Door mirror assembly
13. Door mirror bracket
14. Bracket
15. Speaker box
16. Water-proof sheet
17. Window glass
18. Window regulator/Power window motor
19. Glass run
20. Glass run rear channel
21. Inside lever
22. Door lock assembly/Door lock actuator
23. Glass run front channel
24. Door lock cylinder
25. Outside handle