1997 CADILLAC CATERA light

Downloaded from www.Manualslib.com manuals search engine If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did you just drive through a deep puddle of water?
If
so, your electrical system may be wet. The condition
will usually be corrected when the electrical system
dries out.
A few driving trips should turn the light off.
Are you low on fuel?
As your engine starts to run out of fuel, your engine may
not run as efficiently as designed since small amounts of
air are sucked into the fuel line causing a misfire. The
system can detect this. Adding fuel should correct this
condition. Make sure to install the fuel cap properly. It
will take
a few driving trips to turn the light off.
Have you recently changed brands of fuel?
If
so, be sure to fuel your vehicle with quality fuel (see
“Fuel” in the Index). Poor fuel quality will cause your
engine not to run as efficiently as designed. You may
notice this as stalling after start-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling on acceleration. (These
conditions may go away once the engine is warmed up.)
This will be detected by
the system and cause the light
to turn on.
If you experience one or more of these conditions,
change the fuel brand you use. It will require at least one
full tank of the proper fuel to
turn the light off.
If none of the above steps have made the light turn off,
have your dealer or qualified service center check the
vehicle. Your dealer has the proper test equipment and
diagnostic tools to
fix any mechanical or electrical
problems that may have developed.
2-71

Downloaded from www.Manualslib.com manuals search engine Oil Pressure LighVGage
J
80
2
This light and gage tell you if there could be a problem
with the engine oil pressure.
The gage shows the engine oil pressure in pounds per
square inch (psi). Canadian vehicles show pressure in
kilopascals (kPa).
The oil light goes on when
you turn the key to RUN or
START. It goes off once you start the engine. That’s a
check
to be sure the light works. If it doesn’t come on,
be sure to have it fixed
so it will be there to warn you if
something goes wrong. When
the light
comes on and stays on, it means that oil
isn’t flowing through the engine properly. You could be
low on oil and you might have
some other system
problem.
I
Don’t 1 :p driving if the oil pressure is low. If
you do, your engine can become
so hot that it
catches fire. You or others could be burned.
Check your oil
as soon as possible and have your
vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.
2-72

Downloaded from www.Manualslib.com manuals search engine Check Oil Light Brake To Shift Light
This light shoula come on
briefly while you are
starting the engine. If the
light doesn’t come on,
have it repaired.
If the light
comes
on while starting and
stays on, the engine oil level
should be checked.
Prior to checking the oil level, be sure your vehicle has
been shut off for several minutes and
is on a level
surface. Check the oil level and bring it to the proper
level. See “Engine Oil” in the Index.
Note:
A false check oil light may be generated when
parking
on steep grades.
The oil level monitoring system only checks the oil
during the brief period between turning the key on and
engine start. It does not monitor the engine oil level
while the engine is running. Additionally,
an oil level
check is only performed
if the engine has been turned
off for a considerable amount of time allowing the oil
normally
in circulation to drain back into the oil pan. This
light will come on to
remind
you that you must
press the brake pedal to
shift out
of PARK (P).
BRAKE TO
SHIFT
I
Cruise Control Light
This light comes on
whenever you set your
vehicle’s cruise control.
CRUISE
2-73

Downloaded from www.Manualslib.com manuals search engine Low Washer Fluid Warning Light
This light will come on
when
you turn on the
ignition and the windshield
washer fluid container is
less than one-third full.
Trunk Ajar Light
This light will come on if
your vehicle’s trunk is not
completely closed.
2-74

Downloaded from www.Manualslib.com manuals search engine Fuel Gage Low Fuel Light
The fuel
gage shows
approximately how much
fuel is in the tank. It works
only when the ignition is in
the
RUN position.
Rere
are a few concerns some owners have had about
the fuel gage. All of these situations are normal and do
not indicate that anything is wrong with the fuel gage.
At the gas station the gas pump shuts off before the
The gage may change when you turn, stop or
gage reads
E
speed
up. If
the
fuel level is low
(approximately
two gallons
of fuel remain in the fuel
tank),
a light will come on
and stay on until you add
fuel. It will also come on for
a few seconds when you
first turn
on the ignition as a
check to show it’s working.
If it doesn’t come on then,
have it fixed.
--
--nsmission Warning Light
0
This light comes on briefly
when the ignition is turned
on. If the light remains on
or lights up while driving,
there may be a fault in the
automatic transmission.
Have your vehicle serviced.
2-75

Downloaded from www.Manualslib.com manuals search engine Leveling Indicator Light Brake Pad Wear Indicator Light
LEVELING
This light comes on steady
when the rear load level in
your vehicle changes. This light comes on when
the brake pads on your
vehicle have significantly
worn. The pads will have to
be replaced,
so have your
vehicle serviced soon.
Do not drive your vehicle when this light is on. The rear
of your vehicle is too low and part of the body or the
rear axle may
be damaged when driving over bumpy
roads. When the light goes out, leveling is complete.
This procedure is automatic
-- you don’t have to
do anything.
If the light comes on flashing, there may be a problem
with the leveling system. You should reduce your
vehicle speed and have your vehicle serviced soon.

Downloaded from www.Manualslib.com manuals search engine AM-FM Stereo with Cassette Tape Player
and Optional Compact Disc Player DSPL: Press this button to display the station
being played.
I I Finding a Station
BAND:
Press this button to select AM, FM1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek
to the next higher or lower radio station. Pressing and
holding this button until a chime sounds puts the radio
in a tune mode. In
this mode, higher or lower radio
stations are advanced
to in small increments until the
SEEK-TUNE button is released. Tuning stops when
you release
this button. If you press and hold the
SEEK-TUNE button again within five seconds of being
in the tune mode, tuning will continue. Waiting longer
than five seconds places the radio back in the seek mode.
SCAN: Press this button and SCAN will appear on the
For information on the compact disc player, see "Trunk
display. Use SCAN to listen to stations for a few
Mounted
CD Changer'' later in this section.
seconds. The radio will go to a station, stop for a few
Playing the Radio
PWRNOL:
Press this knob lightly to release it from its
stored position. The system will
turn on. Press the knob
again to
turn the system off. To increase volume, turn the
knob clockwise.
Turn it counterclockwise to decrease
volume. The volume level will appear
on the display. seconds,
then
go on to the next station. Press this button
again
to stop scanning.
3-10

Downloaded from www.Manualslib.com manuals search engine PUSHBUTTONS: The six numbered pushbuttons let
you return
to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
you hear a chime. The sound will mute. When it
returns, release the button. Whenever you press that
numbered button, the station you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hold SCAN for two to three
seconds until PRESET SCAN appears on the display to
listen to each of your preset stations for a few seconds
(factory presets which have not been reprogrammed
with your stations will be ignored). The radio will go
to the first preset station stored on your pushbuttons,
stop for a few seconds, then go on to the next preset
station. Press SCAN again
to stop scanning. If a preset
station has weak reception, the radio will not stop at the
preset station.
Setting the Tone
BASS: Press this knob lightly so it extends. Turn the
knob clockwise
to increase and counterclockwise to
decrease bass.
TREB: Press this knob lightly so it extends. Turn the
knob clockwise to increase and counterclockwise to
decrease treble.
If a station is weak or noisy, you may
want to decrease the treble.
Push these knobs back into their stored positions
when
you’re not using them.
Adjusting the Speakers
BAL: Press this knob lightly so it extends. Turn the
knob clockwise to adjust sound to the right speakers
and counterclockwise for
the left speakers. The middle
position balances the sound between the speakers.
FADE: Press this knob lightly so it extends. Turn the
knob clockwise to adjust the sound to the front speakers
and counterclockwise for the rear speakers. The middle
position balances the sound between the speakers.
Push these knobs back into their stored positions when
you’re not using them.
3-11