Page 94 of 338

Downloaded from www.Manualslib.com manuals search engine Headlamp High/Low Changer Windshield Wipers
With
the twilight sentinel on or with the lamp control
dial turned to the headlamp position, push the turn
signal lever on the driver’s side of the steering wheel
away from you to turn on the high-beam headlamps.
This light on on the
instrument panel will be
on,
indicating high-beam usage.
Pull the lever back to the original position to return to
low-beam headlamps. For more information, see
“Headlamps” later in this section.
Flash-To-Pass
This lets you use the high-beam headlamps to signal the
driver in front of you that you want to pass.
Pull the turn signal lever toward you and release. The
high-beam headlamps will briefly
turn on and then off.
L
L
b
I
WIPER: Move the lever on the passenger’s side of the
steering wheel up and down to control the wipers.
MIST Tap the lever up and then release it for a single
wipe cycle. For more cycles, pull and hold the lever.
= (HIGH): Move the lever all the way up for a fast
wiper speed.
- (LOW): The third position up controls the low
wiper speed.
-- (DELAY): This is for a controlled delay setting.
Rotate the control dial on the lever to increase
or
decrease the delay between wipe cycles.
o (OFF): This position turns off the wipers.
2-33
Page 100 of 338

Downloaded from www.Manualslib.com manuals search engine -4
700< Parking lamps, front and rear sidemarker
lamps, taillamps, license plate lamps, ashtray lamps,
backlighting to the radio controls and instrument
panel lights.
so Headlamps .
$0 Fog lamps.
TWILIGHT Twilight sentinel.
OFF Turns the twilight sentinel system off.
@ Instrument panel brightness control.
Turn the lamp control dial clockwise to the first position
to turn on the parking lamps, front and rear sidemarker
lamps, taillamps, license plate lamps, ashtray lamps,
instrument panel lights and backlighting to the center
console controls.
Rotate the lamp control dial counterclockwise to turn
the lamps
off.
Headlamps
Rotate the lamp control dial clockwise to turn on the
low-beam headlamps.
To turn on the high-beam headlamps, the low-beam
headlamps must already be on. Push the turn signal lever
on the left side of the steering wheel away from you to
engage the high-beam headlamps. Pull the lever toward you to return
to the low-beam headlamps. For more
information, see “Headlamp High/Low Changer” earlier
in this section.
Rotate the lamp control dial counterclockwise
to turn
the headlamps off.
Note that if the headlamps are activated while driving
and then you turn your vehicle’s ignition off while the
lamp dial is still turned on, the headlamps will turn
off.
Turn the lamp control dial counterclockwise to turn the
headlamps off and to stop the reminder chime from
sounding. (If you want the headlamps to remain on, you
must manually turn the lamp control dial off and then
back on to the headlamp position. The headlamps will
stay
on until manually turned off again.)
2-39
Page 101 of 338

Downloaded from www.Manualslib.com manuals search engine Wiper Activated Headlamps
This feature activates the low-beam headlamps, parking
lamps, sidemarker lamps and taillamps after the
windshield wipers have been in use for about
20 seconds.
The wiper activated headlamps light the way in poor
weather and also make your vehicle more visible to
other drivers.
If the wipers are on and the ignition switch
is turned off, the headlamps will immediately turn off.
The headlamps will also deactivate if the windshield
wipers have been turned
off for about 20 seconds.
Lamps On Reminder
You will hear a warning buzzer if you open the door
while leaving the lamps
on, if the manual headlamp
control is activated. An exception to this is when you’re
using the twilight sentinel.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others
to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
The DRL system will make the high-beam headlamps
come
on at reduced brightness when:
0 your vehicle’s ignition is in RUN or START,
0 the low-beam headlamps are off (the manual lamp
switch is in the
off or park lamp position) and
0 your vehicle’s transmission is shifted out of
PARK (P).
2-40
Page 102 of 338

Downloaded from www.Manualslib.com manuals search engine When DRL are on, only the high-beam headlamps (at
reduced brightness) will be on.
No other exterior lamps
such as the parking lamps, taillamps, etc. will be on
when the
DRL are being used. The instrument panel
won’t be lit up either.
When the twilight sentinel is on and it’s dark enough
outside, the high-beam headlamps (at reduced intensity)
will change to low-beam headlamps. When it’s bright
enough outside, the regular lamps will go off, and the
high-beam headlamps change to the reduced brightness
of DRL.
To idle your vehicle with the headlamps off, turn off the
twilight sentinel switch and shift the transmission into
PARK (P). Placing your vehicle in PARK
(P) disables
the DRL. The DRL will stay
off until you shift out of
PARK
(P).
If you’re not in PARK (P)
and the twilight sentinel
system
is turned off (and it’s
dark enough outside), the
DRL will remain active and
this light on the instrument
panel will appear as a
reminder that headlamps
are required.
The following conditions will override the DRL:
your vehicle’s transmission is shifted back into
PARK
(P) with the ignition in RUN or START,
the low-beam headlamps are turned on (using the
manual lamp control dial),
the wiper activated headlamps are in use (DRL will
come back on
20 seconds after wipers have turned off),
using the flash-to pass feature and
turning on twilight sentinel.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
2-41
Page 103 of 338
Downloaded from www.Manualslib.com manuals search engine Fog Lamps
Use the fog lamps for better
vision in foggy or misty
conditions. Press this button
to turn the fog lamps on and
press the button again to
turn the lamps
off. (The fog
lamps only work when the
parking lamps or the
low-beam headlamps
are on.) This light
on the instrument
panel will come on when
the fog lamp button
$0
is pressed.
If you switch on the high-beam headlamps, the fog
lamps will turn off. They’ll turn back on again when you
switch to low-beam headlamps.
Cornering Lamps
The cornering lamps come on when the headlamps or
parking lamps are on and you signal a turn. They
provide more light for cornering.
2-42
Page 183 of 338

Downloaded from www.Manualslib.com manuals search engine Here are some tips on night driving,
0 Drive defensively.
0 Don’t drink and drive.
Since you can’t see as well, you may need to slow
down and keep more space between you and
other vehicles.
0 Slow down, especially on higher speed roads. Your
headlamps can light up only
so much road ahead.
In remote areas, watch for animals.
If you’re tired, pull off the road in a safe place
and rest.
Night Vision
No one can see as well at night as in the daytime. But as
we get older these differences increase. A 50-year-old
driver may require at least twice as much light to see the
same thing at night as a 20-year-old.
What you do in the daytime can also affect your night
vision. For example, if you spend the day
in bright
sunshine you
are wise to wear sunglasses. Your eyes will
have less trouble adjusting to night. But if you’re
driving, don’t wear sunglasses at night. They may cut
down
on glare from headlamps, but they also make a lot
of things invisible.
You can be temporarily blinded by approaching
headlamps. It can take a second’or two,
or even several
seconds, for your eyes to readjust to the
dark. When
you
are faced with severe glare (as from a driver who
doesn’t lower the high beams, or a vehicle with
misaimed headlamps), slow down
a little. Avoid staring
directly into the approaching headlamps.
4-16
Page 275 of 338
Downloaded from www.Manualslib.com manuals search engine Headiamp
1. With a screwdriver, unscrew the fastener on the
headlamp cover and then remove the cover
to
gain access (see Step 1 under “Front Turn Signal
Lamp”). Note that the inner bulb is for the
low-beam headlamp and the outer bulb is for
the high-beam headlamp.
IF-
P
3. Remove the plug connector from the bulb.
2. Remove the black rubber cap that protects the
bulb area.
6-32
Page 279 of 338
Downloaded from www.Manualslib.com manuals search engine It is recommended that the upper limit not exceed plus
0.4 degrees from the center of the bubble. Other drivers
may flash their high beams at you if your adjustment is
much above plus
0.4 degrees.
If you find that the headlamp aiming needs adjustment,
follow these steps: Adjustment screws can be turned with an
E8 Torx@
socket or a
TI 5 Torx screwdriver.
2. Check the vertical aim for each headlamp and adjust
it as necessary. You can see the level through the
headlamp assembly. Turn the vertical aiming screw,
on the outboard side of the headlamp assembly, until
the bubble in the level is centered at
0 (zero). 1. With a screwdriver, unscrew the fastener on the
headlamp cover and then remove the cover to be able
to
see the back of the headlamp assembly.
3. If the horizontal aim needs adjusting, see your
Catera dealer.
6-36