1997 ACURA NSX immobilizer

II. Engine Control Module (ECM) Reset Procedure

Either of the following actions, will reset the ECM.

• Using the OBD II scan tool or Honda PGM Tester to clear the ECM's memory.

NOTE: See the OBD II scan tool or Honda PGM Tester user's manuals for specific operating instructions.

• Turn the ignition switch OFF. Remove the CLOCK (7.5 A) fuse from the under-hood fuse/relay box for 10 seconds.

NOTE: If the CLOCK (7.5 A) fuse is removed when the ignition switch is in the ON (II) position, the MIL will come

on and the ECM will store a DTC.

UNDER-HOOD

FUSE/RELAY BOX
CLOCK

(7.5 A) FUSE

III. Final Procedure (this procedure must be done after any troubleshooting)

1. Remove the SCS Service Connector if it is connected. If the SCS service connector is connected and there are no

DTCs stored in the ECM, the MIL will stay on when the ignition switch is turned on.

2. Do the ECM Reset Procedure.

3. Turn the ignition switch OFF.

4. Disconnect the OBD II scan tool or Honda PGM Tester from the Data Link Connector (16P).

IV. Known-Good ECM Substitution

The ECM is part of the immobilizer system. If you substitute a known-good ECM, the ECM will have a different immo-

bilizer code. In order for the engine to start, you must rewrite the immobilizer code with the Honda PGM Tester.ProCarManuals.com

Engine Control Module (ECM) Reset Procedure

Either of the following actions, will reset the ECM.

Using the OBD II scan tool or Honda PGM Tester to clear the ECM's memory.

NOTE: See the OBD II scan tool or Honda PGM Tester user's manuals for specific operating instructions.

Turn the ignition switch OFF. Remove the CLOCK (7.5 A) fuse from the under-hood fuse/relay box for 10 seconds.

UNDER-HOOD

FUSE/RELAY BOX
CLOCK

(7.5 A) FUSE

III. Final Procedure (this procedure must be done after any troubleshooting)

1. Remove the SCS Service Connector if it is connected. If the SCS service connector is connected and there are no

DTCs stored in the ECM, the MIL will stay on when the ignition switch is turned on.

2. Do the ECM Reset Procedure.

3. Turn the ignition switch OFF.

4. Disconnect the OBD II scan tool or Honda PGM Tester from the Data Link Connector (16P).

IV. Known-Good ECM Substitution

The ECM is part of the immobilizer system. If you substitute a known-good ECM, the ECM will have a different immo-

bilizer code. In order for the engine to start, you must rewrite the immobilizer code with the Honda PGM Tester.

(cont'd)ProCarManuals.com

Troubleshooting

Engine Control Module Terminal Arrangement (cont'd)

ECM CONNECTOR F (26P)
Wire side of female terminals

NOTE: Standard battery voltage is 12 V.

*: M/T

Terminal

number

1

2

3

4

6

7

8

9

10

10*

11

12

13

14

15

16

17

18

19

20

21

22

24
Wire

color

YEL/WHT

GRN/WHT

BRN

RED

GRY

LT

GRN/BLK

LT

GRN/RED

LTGRN

BLU/ORN

BLU/ORN

BLU/BLK

YEL/RED

BLU/RED

YEL/WHT

GRN/WHT

GRN/WHT

RED/WHT

BLU

BLU/YEL

GRN/YEL

LT GRN/YEL

WHT/YEL

RED/BLU
Terminal name

VCC1

(SENSOR VOLTAGE)

SG1 (SENSOR GROUND)

IMO CODE (IMMOBILIZER

CODE)

FLR2 (FUEL PUMP RELAY 2)

BKSW2 (BRAKE SWITCH 2)

CCRESSW (CRUISE

CONTROL RESUME SWITCH)

CC SETSW (CRUISE

CONTROL SET SWITCH)

CC MSW (CRUISE

CONTROL MAIN SWITCH)

CC ATSSW (CRUISE

CONTROL A/T GEAR

POSITION SWITCH)

CC CLSW (CRUISE

CONTROL CLUTCH SWITCH)

CCIL (CRUISE CONTROL INDI-

CATOR LIGHT)

AP2 (ACCELERATOR

POSITION SENSOR CIRCUIT 2)

AP1 (ACCELERATOR

POSITION SENSOR CIRCUIT 1)

VCC3 (SENSOR VOLTAGE)

SG3 (SENSOR GROUND)

BKSW1 (BRAKE SWITCH 1)

MTSL (REVERSE LOCKOUT

RELAY OUT)

VREF (REFERENCE VOLTAGE)

VT SOLF (FRONT VTEC

SOLENOID VALVE)

VT SOLR (REAR VTEC

SOLENOID VALVE)

ATSDL B (A/T Fl DATA LINE B)

ATSDL (A/T Fl. DATA LINE A)

TCSSDL (TCS DATA LINE)
Description

Provides sensor voltage

Sensor ground

Detects immobilizer signal

Drives fuel pump relay

Detects brake switch 2 signal

Detects resume switch signal

Detects set switch signal

Power source for the cruise

control system

Detects A/T gear position switch

signal

Detects clutch switch signal

Drives cruise control indicator

light

Detects accelerator position

sensor circuit 2 signal

Detects accelerator position

sensor circuit 1 signal

Provides sensor voltage

Sensor ground

Detects brake switch 1 signal

Drives reverse lockout relay

Provides reference voltage to

TCM

Drives front VTEC solenoid

valve

Drives rear VTEC solenoid valve

Detects data from the TCM

Sends data to the TCM

Interface for TCS control unit
Signal

With ignition switch ON (II): about 5 V

With ignition switch OFF: 0 V

With engine at low rpm: battery voltage

With engine at high rpm: 0 V

With brake pedal released and cruise

control main switch ON: battery voltage

With brake pedal depressed: 0 V

With resume switch released: 0 V

With resume switch depressed: battery

voltage

With set switch released: 0 V

With set switch depressed: battery

voltage

With cruise control main switch ON:

battery voltage

With cruise control main switch OFF: 0 V

In , or position: 0 V

In any other position: approx. 8 V

With clutch pedal released: approx. 8 V

With clutch pedal depressed: 0 V

With cruise control ON: 0 V

With cruise control OFF: battery voltage

With accelerator fully open: about 4.5 V

With accelerator fully closed: about 0.5 V

With accelerator fully open: about 4.5 V

With accelerator fully closed: about 0.5 V

With ignition switch ON (II): about 5 V

With ignition switch OFF: 0 V

With brake pedal released: 0 V

With brake pedal depressed: battery

voltage

With vehicle speed above 13 mph

(20 km/h): 0 V

With vehicle speed below 9 mph

(15 km/h): battery voltage

With ignition switch ON (II): about 5 V

With ignition switch OFF: 0 V

With engine at low rpm: 0 V

With engine at high rpm: battery voltage

With engine at low rpm: 0 V

With engine at high rpm: battery voltage

With engine running: pulses

With engine running: pulses

With engine running: pulsesProCarManuals.com

Relay and Control Unit Locations

Dashboard

IMMOBILIZER CONTROL UNIT
CLIMATE CONTROL UNIT

TURN SIGNAL/HAZARD

RELAY

DASHBOARD

LOWER COVER

INTEGRATED

CONTROL UNIT

UNDER-DASH FUSE BOXProCarManuals.com

Ignition Switch

Steering Lock Removal/Installation (cont'd)

8. Center-punch the shear bolt, and drill its head off

with a 5 mm (3/16 in) drill bit. Do not damage the

switch body.

9. Remove the shear bolt from the switch body.

10. Insert the key, and turn it to "I".

11. Push the lock pin, and pull out the steering lock

assembly.

STEERING LOCK

BODY
Installation:

1. Turn the key to "I", push the pin, and insert the

steering lock assembly into the steering column

until it clicks into place.

2. Loosely tighten the new shear bolt. Make sure the

projection on the ignition switch is aligned with the

hole in the steering column.

3. Insert the ignition key, and check for proper opera-

tion of the steering wheel lock and that the ignition

key turns freely.

4. Tighten the shear bolt until the hex head twists off.

5. Install in the reverse order of removal. Install the 3P

connector harness carefully because this harness

serves as communication link.

SHEAR BOLT

TWIST-OFF PORTION

6. After installing, check the immobilizer system.ProCarManuals.com

Gauge Assembly

Bulb Locations

GAUGE LIGHTS (1.4 Wx 2)

SRS INDICATOR LIGHT (1.4 W)

RIGHT TURN SIGNAL INDICATOR LIGHT 11.4 W)

EPS INDICATOR LIGHT (1.4 W)

BRAKE SYSTEM LIGHT (1.4 W)

SEAT BELT REMINDER LIGHT (1.4 W)

IMMOBILIZER INDICATOR

LIGHT (1.4 W)

LOW FUEL INDICATOR

LIGHT (1.4 W)

GAUGE LIGHT

(1.4
W)
TCS INDICATOR LIGHT (1.96 W)

LEFT TURN SIGNAL INDICATOR LIGHT (1.4 W)

ABS

INDICATOR LIGHT (1.4 W)

CHARGING SYSTEM LIGHT (1.4 W)

MALFUNCTION

INDICATOR

LAMP (MIL)

(1.4
W)

CRUISE INDICATOR LIGHT

(1.96
W)
LOW OIL PRESSURE

INDICATOR

LIGHT (1.4 W)

GAUGE LIGHT

.4W)

GAUGE LIGHT

(3.0
W)
GAUGE LIGHT

GAUGE LIGHT HIGH BEAM INDICATOR (3.0 W)

(3.0 W) LIGHT (1.4 W)ProCarManuals.com

Immobilizer Syste m
Componen t Locatio n Inde x
IMMOBILIZE R INDICATO R LIGH T
(I n th e gaug e assembly )
Bul b Locations , pag e 23-12 8
CLUTC H INTERLOC K SWITC H
(M/T)Test, pag e 23-8 0
IMMOBILIZE R CONTRO L
UNITInpu t Test , pag e23-33 4
IMMOBILIZE R RECEIVE R
Test , pag e 23-33 5
Replacement , pag e 23-33 6
A/T GEA R POSITIO N
SWITC H
Test , pag e 23-16 2
STARTE R CU T RELA YWire colors : BLK/WHT ,
BLK/WHT , BLK/GRN ,
an d BLK/BL U
Test , pag e 23-8 0
TRANSPONDE R(Built int o th e ignitio n key )Test , pag e 23-33 5
IGNITIO N KEY(Maste r an d vale t keys )
ProCarManuals.com

Immobilizer Syste m
Descriptio n
The vehicl e i s equippe d wit h a n immobilize r syste m tha t wil l disabl e th e vehicl e unles s th e prope r ignitio n ke y i s used .
Thi s syste m consist s o f a transponde r locate d i n th e ignitio n key , a receiver , a contro l unit , a n indicato r light , an d th e ECM .
Th e vehicl e ha s tw o kind s o f keys .
BLAC K
GRAY
The maste r ke y i s for :
— ignitio n switch .
— doo r locks .
— trun k lock .
— glov e bo x lock .
Th e vale t ke y i s for :
— ignitio n switch .
— doo r locks .
Th e learnin g ke y i s fo r rewritin g th e immobilize r sys -
tem.
NOTE : Thi s ke y canno t star t th e engine ; d o no t us e i t
excep t fo r rewritin g th e system . I f someon e trie s t o
star t th e engin e wit h th e learnin g key , al l maste r an d
vale t key s mus t b e relearned .
Whe n th e ke y i s inserte d i n th e ignitio n an d turne d t o th e (II ) position , th e immobilize r contro l uni t send s powe r t o th e
transponde r throug h th e receiver .
Th e transponde r the n send s a code d signa l bac k throug h th e receive r t o th e contro l unit .
Th e contro l uni t i n tur n signal s th e ECM , a s wel l a s th e starte r cu t relay .
RED
IMMOBILIZE R RECEIVE R
IGNITION KE Y(Has built-i n transponder )
23-330ProCarManuals.com