1996 TOYOTA TERCEL ignition

Z08448
Wire Harness Side
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-17
1996 TERCEL (RM440U)
6. INSPECT D.R.L. MAIN RELAY CIRCUIT
(a) Disconnect the connector from relay and inspect the con-
nector on wire harness side, as shown.
Tester connectionConditionSpecified condition
7 - GroundHeadlight dimmer switch Low beam or High
beam No continuity
7 - GroundHeadlight dimmer switch Flash Continuity
8 - GroundParking brake switch OFF
(Switch pin pushed in)No continuity
8 - GroundParking brake switch ON
(Switch pin released)Continuity
12 - GroundConstantContinuity
13 - GroundConstantContinuity
16 - GroundHeadlight dimmer switch Low beam No continuity
16 - GroundHeadlight dimmer switch High beam or Flash Continuity
2 - Ground
18 - GroundIgnition switch LOCK or ACCNo voltage
2 - Ground
18 - GroundIgnition switch ONBattery positive voltage
4 - GroundConstantBattery positive voltage
6 - GroundConstantBattery positive voltage
10 - GroundConstantBattery positive voltage
11 - GroundEngine StopNo voltage
11 - GroundEngine RunningBattery positive voltage
15 - GroundConstantBattery positive voltage
If circuit is as specified, try replacing the relay with a new one.
If the circuit is not as specified, inspect the circuit connected to
other parts.

BE0R0-01
I05915
Engine Room R/B

HAZ-HORN Fuse
Hazard Warning Switch
Turn Signal and Hazard Warning Lights
Turn Signal Flasher
Turn Signal Switch
Ignition Switch
Turn Signal and Hazard Warning Lights I/P J/B

TURN Fuse
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
BE-21
1043 Author
: Date
:
1996 TERCEL (RM440U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION

BE0R4-01
I05917
Ignition Switch
I/P J/B

GAUGE Fuse
Back-up Lights
Back-up Light Switch
Park/Neutral Position Switch
- BODY ELECTRICALBACK-UP LIGHT SYSTEM
BE-25
1047 Author
: Date
:
1996 TERCEL (RM440U)
BACK-UP LIGHT SYSTEM
LOCATION

BE0RA-02
I05953
Combination Meter

Meter CircuitDoor Lock Control Relay or Theft Deterrent ECU
ECM
Ignition Switch Rheostat Light Control Volume
ABS ECUBrake Fluid Level Warning Switch
Engine Room R/B

DOME Fuse
I/P J/B

Integration Relay

GAUGE Fuse

IGN Fuse

TURN Fuse

TAIL FuseAirbag Sensor Assembly
Parking Brake Switch
- BODY ELECTRICALCOMBINATION METER
BE-33
1996 TERCEL (RM440U)
LOCATION

BE26Q-01
N12803N12541I22670
w/ Tachometer
A
B
w/o Tachometer
A
B
N13601
Ignition
Switch
BatteryFuel
Receiver
Gauge
Z08460
N12804
A
BC
DE F BE-38
- BODY ELECTRICALCOMBINATION METER
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT VEHICLE SPEED SENSOR OPERATION
Check that there is continuity between terminals A and B four
times for every revolution of the speedometer shaft.
If operation is not as specified, replace the speedometer.
2. INSPECT FUEL RECEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, check that the receiver gauge
needle indicates EMPTY.
(c) Connect terminals 5 and 6 on the wire harness side con-
nector through a 3.4 W test bulb.
(d) Turn the ignition switch ON, check that the bulb lights up
and the receiver gauge needle moves towards the full
side.
HINT:
Because of the silicon oil in the gauge, it will take a short time
for needle to stabilize.
If operation is not as specified, inspect the receiver gauge resis-
tance.
3. INSPECT FUEL RECEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
w/ Tachometer:
Between terminalsResistance (W)
A - BApprox. 115.8
A - CApprox. 177.2
B - CApprox. 61.4

N12805
A
BC
N15789
EF
1/256
Z08044
Ignition
Switch
BatteryWarning Light
N13602
1
4
- BODY ELECTRICALCOMBINATION METER
BE-39
1996 TERCEL (RM440U)
w/o Tachometer:
Between terminalsResistance (W)
A - BApprox. 171.2
A - CApprox. 272.8
B - CApprox. 101.6
If resistance value is not as specified, replace the receiver
gauge.
4. INSPECT FUEL SENDER GAUGE RESISTANCE
Measure the resistance between Red Cable and Black Cable.
Float position : mm (in.)Resistance (W)
F : Approx. 13.0 ± 3
(0.512 ± 0.118)3 ± 1.0
1/2 : Approx. 61.0 (2.402)29 ± 4.8
E : Approx. 124.0 ± 3
(4.882 ± 0.118)110 ± 7.7
If resistance value is not as specified, replace the sender
gauge.
5. INSPECT FUEL LEVEL WARNING LIGHT
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 1 and 3 on the wire harness side con-
nector.
(c) Turn the ignition switch ON, check that the warning light
lights up.
If the warning light does no light up, test the bulb.
6. INSPECT FUEL LEVEL WARNING SWITCH
OPERATION
(a) Apply battery positive voltage between terminals and
through a 3.4 W test bulb, check that the bulb lights up.
HINT:
It will take a short time for bulb to light up.

N13603
1
4
Z08045
Engine Coolant Temperature Gauge
Ignition
Switch
BatterySender
Gauge
Z07424
Engine Coolant Temperature Gauge
BatteryTest Bulb
(3.4 W)
N12804
A
BC
DE F
N12806
A B
C BE-40
- BODY ELECTRICALCOMBINATION METER
1996 TERCEL (RM440U)
(b) Submerge the switch in fuel, and check that the bulb goes
out.
If operation is not as specified, replace the sender gauge.
7. INSPECT RECEIVER ENGINE COOLANT
TEMPERATURE GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connecter
through a 3.4 W test bulb.
(d) Turn the ignition switch ON, check that the bulb lights up
and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge. Then, re-
check the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
8. INSPECT ENGINE COOLANT TEMPERATURE
RECEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
w/ Tachometer:
Between terminalsResistance (W)
D - EApprox. 51.0
D - FApprox. 148.6
E - FApprox. 199.6
w/o Tachometer:
Between terminalsResistance (W)
A - BApprox. 54.0
A - CApprox. 175.7
B - CApprox. 229.7
HINT:
Connect the test leads so that the current from the ohmmeter
can flow according to the above order. This circuit includes the
diode.

BE0044
Ignition
Switch
BatteryWarning Light
BE0146
BE1217
Ignition
Switch
BatteryWarning Light
BE1601
ON OFF
- BODY ELECTRICALCOMBINATION METER
BE-41
1996 TERCEL (RM440U)
If resistance value is not as specified, replace the receiver
gauge.
9. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
10. INSPECT LOW OIL PRESSURE SWITCH CONTINUITY
(a) Disconnect the connector from the switch.
(b) Check that there is continuity between terminal and
ground with the engine stopped.
(c) Check that there is no continuity between terminal and
ground with the engine running.
HINT:
Oil pressure should be over 49 kPa (0.5 kgf/cm
2, 7.1 psi).
If operation is not as specified, replace the switch.
11. INSPECT BRAKE SYSTEM WARNING LIGHT
(a) Disconnect the connectors from the level warning switch
and parking brake switch.
(b) Connect terminals on the wire harness side connector of
the level warning switch connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
12. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
CONTINUITY
(a) Check that there is no continuity between terminals with
the switch OFF (float up).
(b) Check that there is continuity between terminals with the
switch ON (float down).
If operation is not as specified, replace the switch.