1996 TOYOTA TERCEL steering

R12040
SST
Fulcrum
Length
N00349
R15520
0 mm
6 mm
(0.24 in.)
R15519
SR-44
- STEERINGMANUAL STEERING GEAR
1996 TERCEL (RM440U)
10. INSTALL RH AND LH CLAW WASHERS AND RACK
ENDS
(a) Install a new washer, and temporarily tighten the rack
end.
HINT:
Align the claws of the washer with the steering rack grooves.
(b) Using a spanner, hold the steering rack steadily and using
SST, torque the rack end.
SST 09922-10010
Torque: 43 N´m (434 kgf´cm, 31 ft´lbf)
NOTICE:
Use SST 09922-10010 in the direction shown in the illustra-
tion.
HINT:
Use a torque wrench with a fulcrum length of 345 mm (13.58
in.).
(c) Using a brass bar and hammer, stake the washer.
NOTICE:
Avoid any impact on the rack.
11. INSTALL RH AND LH BOOTS, CLAMPS AND CLIPS
(a) Install the rack boot.
NOTICE:
Be careful not to damage or twist the boot.
(b) Install the clamp screw, as shown in the illustration.
(c) Install the clip.
HINT:
Face the open ends of the clips outward/upward as shown in
the illustration, to avoid damage to the boot.
12. INSTALL RH AND LH TIE ROD ENDS AND LOCK NUTS
(a) Screw the lock nut and tie rod end onto the rack end until
the matchmarks are aligned.
(b) After adjusting toe-in, torque the nut.
(See page SA-4)
Torque: 47 N´m (480 kgf´cm, 35 ft´lbf)

SR0KW-02
- STEERINGMANUAL STEERING GEAR
SR-45
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL MANUAL STEERING GEAR ASSEMBLY
Install the gear assembly from the LH of the vehicle.
2. INSTALL 2 GROMMETS AND BRACKETS
Torque the 2 bolts and nuts.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
3. CONNECT SLIDING YOKE (See page SR-20)
4. INSTALL COLUMN HOLE COVER
Torque the 4 nuts.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
5. CONNECT RH AND LH TIE ROD ENDS (See page SA-10)
6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
HINT:
Do it with the front of the vehicle jacked up.
7. w/ Airbag:
CENTER SPIRAL CABLE (See page SR-20)
8. INSTALL STEERING WHEEL
(a) Install the wheel at straight-ahead position.
(b) Temporarily tighten the wheel set nut.
(c) Connect the connector.
9. CHECK STEERING WHEEL CENTER POINT
10. w/ Airbag:
TORQUE STEERING WHEEL SET NUT
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
11. w/ Airbag:
INSTALL STEERING WHEEL PAD (See page SR-20)
12. CHECK FRONT WHEEL ALIGNMENT (See page SA-4)

SR0KX-04
SR-46
- STEERINGPOWER STEERING GEAR
966 Author
: Date
:
1996 TERCEL (RM440U)
POWER STEERING GEAR
COMPONENTS

- STEERINGPOWER STEERING GEAR
SR-47
967 Author
: Date
:
1996 TERCEL (RM440U)

Union Seat SR-48
- STEERINGPOWER STEERING GEAR
968 Author
: Date
:
1996 TERCEL (RM440U)

SR0KY-02
R11074
SST
SR4244
- STEERINGPOWER STEERING GEAR
SR-49
1996 TERCEL (RM440U)
REMOVAL
1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
2. w/ Airbag:
REMOVE STEERING WHEEL PAD (See page SR-13)
3. w/ Airbag:
REMOVE STEERING WHEEL (See page SR-13)
4. DISCONNECT RH AND LH TIE ROD ENDS (See page
SA-10)
5. REMOVE COLUMN HOLE COVER
Remove the 2 bolts and nut.
6. DISCONNECT SLIDING YOKE (See page SR-13)
7. REMOVE OXYGEN SENSOR
8. REMOVE FRONT EXHAUST PIPE
(a) Remove the 2 bolts, compression springs and gasket.
(b) Remove the bolt, clamp and gasket.
(c) Disconnect the 2 rings.
9. REMOVE ENGINE REAR MOUNT INSULATOR
Remove the 6 bolts.
10. REMOVE ENGINE REAR MOUNT BRACKET
Remove the 2 bolts.
11. DISCONNECT 2 VACUUM HOSES
12. M/T:
DISCONNECT CONTROL CABLES
(a) Remove the 2 clips and washers.
(b) Remove the 2 clips from the cables.
(c) Disconnect the 2 cables from the control lever housing
support bracket.
13. DISCONNECT PRESSURE FEED AND RETURN
TUBES
Using SST, disconnect the tube.
SST 09631-22020
14. DISCONNECT TUBE CLAMP
Remove the bolt.
15. REMOVE 2 BRACKETS AND GROMMETS
Remove the 2 bolts and nuts.
16. REMOVE PS GEAR ASSEMBLY
(a) Slide the gear assembly to the RH side of the vehicle.
(b) Slide the gear assembly to the LH side and pull it out.

SR17W-02
R11026
SST
R11027
SST
R13122
R11029
SST SR-50
- STEERINGPOWER STEERING GEAR
1996 TERCEL (RM440U)
DISASSEMBLY
NOTICE:
When using a vise, do not overtighten it.
1. SECURE PS GEAR ASSEMBLY IN VISE
Using SST, secure the gear assembly in a vise.
SST 09612-00012
2. REMOVE 2 TURN PRESSURE TUBES
(a) Using SST, remove the tube.
SST 09633-00020
(b) Remove the 2 union seats from the rack housing.
3. REMOVE AIR CONTROL VALVE
4. REMOVE RH AND LH TIE ROD ENDS AND LOCK
NUTS (See page SR-37)
5. REMOVE RH AND LH CLIPS, RACK BOOTS AND
CLAMPS
Using a screwdriver, loosen the clamp.
NOTICE:

Be careful not to damage the boot.

Mark the RH and LH boots.
6. REMOVE RH AND LH RACK ENDS AND CLAW WASH-
ERS (See page SR-37)
7. REMOVE RACK GUIDE SPRING CAP LOCK NUT
Using SST, remove the nut.
SST 09922-10010
NOTICE:
Use SST 09922-10010 in the direction shown in the illustra-
tion.
8. REMOVE RACK GUIDE SPRING CAP
Using a hexagon wrench (21 mm), remove the cap.
9. REMOVE RACK GUIDE SPRING, RACK GUIDE AND
RACK GUIDE SEAT
Remove the seat from the guide.
10. REMOVE RACK HOUSING CAP

SR4297
SST
R06217
SST
Pin
Pin
R11075
SST
R11056
SST
- STEERINGPOWER STEERING GEAR
SR-51
1996 TERCEL (RM440U)
11. REMOVE SELF-LOCKING NUT
Using SST, stop the control valve rotating and remove the nut.
SST 09616-00010
12. REMOVE CONTROL VALVE ASSEMBLY WITH OIL
SEAL AND BEARING
(a) Using snap ring pliers, remove the snap ring from the rack
housing.
(b) Using SST, remove the valve assembly with the oil seal
and bearing.
SST 09613-12010
NOTICE:
Never attempt to tap out the control valve as this would
damage it.
(c) Remove the oil seal from the valve assembly.
(d) Using SST, remove the bearing from the valve assembly.
SST 09950-40010 (09951-04010, 09952-04010,
09953-04020, 09954-04010, 09955-04050,
09957-04010, 09958-04010)
13. REMOVE BEARING
Using a brass bar and hammer, tap out the bearing from the
rack housing.
14. REMOVE CYLINDER END STOPPER AND BUSHING
Using SST, remove the stopper and bushing.
SST 09631-20090