1996 TOYOTA T100 control arm

Downloaded from www.Manualslib.com manuals search engine − INTRODUCTIONTERMS
IN−35
1996 TOYOTA T100 (RM449U) TCM
Transmission Control ModuleTransmission ECU (Electronic Control Unit)
TPThrottle PositionThrottle Position
TRTransmission Range−
TVVThermal Vacuum ValveBimetallic Vacuum Switching Valve (BVSV)
Thermostatic Vacuum Switching Valve (TVSV)
TWCThree−Way Catalytic ConverterThree−Way Catalytic (TWC)
CC
RO
TWC+OCThree−Way + Oxidation Catalytic ConverterCCR + CCo
VA FVolume Air FlowAir Flow Meter
VRVoltage RegulatorVoltage Regulator
VSSVehicle Speed SensorVehicle Speed Sensor (Read Switch Type)
WOTWide Open ThrottleFull Throttle
WU−OCWarm Up Oxidation Catalytic Converter−
WU−TWCWarm Up Three−Way Catalytic ConverterManifold Converter
3GRThird Gear−
4GRFourth Gear−

Downloaded from www.Manualslib.com manuals search engine SS07W−01
− SERVICE SPECIFICATIONSMANUAL TRANSMISSION (R150, R150F)
SS−45
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Transmission x Engine7273053
Stiffener plate x Engine (4WD)3738027
Stiffener plate x Transmission (4WD)3738027
Starter x Transmission3940029
Engine rear mounting x Transmission6566048
Rear end plate x Transmission (2WD)1818513
Clutch release cylinder x Transmission121209
Front exhaust pipe x TWC4849035
Front exhaust pipe support bracket4445033
Front exhaust pipe x Exhaust manifold6263046
Crossmember x Engine rear mounting (4WD)1818013
Engine rear mounting bracket x Engine rear mounting (2WD)1818013
Engine rear mounting bracket x Frame (2WD)5859043
Crossmember x Frame (4WD)9597070
Transmission x Transfer (4WD)3738027
Reverse shift arm bracket set bolt1818513
Rear bearing retainer x Intermediate plate1818513
Shift fork x Shift fork shaft2020014
Straight screw plug1919014
Front bearing retainer x Transmission case1717012
Transmission case x Transfer adaptor3738027
Transmission case x Extension housing3738027
Shift lever housing set bolt3839028
Clutch housing x Transmission case3637027
Oil receiver x Extension housing1111 58
Back−up light switch4445032
Restrict pin3738027
Control shift lever retainer x Transfer adaptor1818513
Control shift lever retainer x Extension housing1818513
Filler and drain plug3738027
Speedometer driven gear (2WD)1111 58

Downloaded from www.Manualslib.com manuals search engine SS−74
− SERVICE SPECIFICATIONSSTEERING
1996 TOYOTA T100 (RM449U) Tie rod end lock nut
5657041
Turn pressure tube union nut10 (13)102 (130)7 (9)
PS gear assembly set bolt and nut8890065
Mount bracket x Suspension crossmember8890065
Control valve shaft x Intermediate shaft3536026
Pressure feed tube x Control valve housing19 (25)195 (250)14 (18)
Return tube x Control valve housing19 (25)195 (250)14 (18)
Tie rod end x Steering knuckle9092067
4WD:
Pressure feed tube x PS gear assembly36 (44)365 (450)26 (33)
Return tube x PS gear assembly36 (44)365 (450)26 (33)
PS gear assembly x Body1421450105
Pitman arm x Cross shaft1771800130
Cross shaft adjusting screw set nut4647034
Side cover x Gear housing6162045
Plunger guide nut2020515
Worm gear valve body assembly x Gear housing6162045
Worm gear valve body assembly x Intermediate shaft3536026
STEERING LINKAGE
Pitman arm x Cross shaft1771800130
Pitman arm x Relay rod9092067
Tie rod clamp bolt2222516
Tie rod assembly x Relay rod9092067
Tie rod assembly x Knuckle arm9092067
Idler arm assembly x Frame1421450105
Relay rod x Idler arm assembly5960043
Steering damper set bolt and nut2526019
Relay rod x Steering damper5960043
IDLER ARM
Idler arm x Idler arm bracket7880058
( ): For use without SST

Downloaded from www.Manualslib.com manuals search engine SS−78
− SERVICE SPECIFICATIONSBODY ELECTRICAL
252 Author: Date:
1996 TOYOTA T100 (RM449U)B − C
Approx. 55.0 Ω
FUEL SENDER GAUGE
Float position mm (in.)Resistance (Ω)
F: Approx. 95 mmApprox. 3.0 Ω
1/2: Approx. 188.0 mmApprox. 32.5 Ω
E: Approx. 283.0 mmApprox. 110.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ Tachometer)Resistance (Ω)
A − BApprox. 150.0 Ω
A − CApprox. 54.0 Ω
B − CApprox. 138.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ o Tachometer)
A − BApprox. 25.0 Ω
OIL PRESSURE RECEIVER GAUGE
A − BApprox. 25.0 Ω
DOOR LOCK CONTROL RELAY (Wire Harness Side)
2 − Ground (Constant)Battery positive voltage
8 − Ground (Ignition Switch LOCK or ACC)No voltage
8 − Ground (Ignition Switch ON)Battery positive voltage
13 − Ground (Key unlock warning switch OFF (Ignition key removed))No voltage
13 − Ground (Key unlock warning switch ON (Ignition key set))Battery positive voltage
CRUISE CONTROL ECU (wire harness side)
24 − 26 (constant)Approx. 2.0 kΩ
25 − 26 (Actuator arm turned)Resistance change even
10 − Ground (Brake pedal position: Released)Approx. 38.0 Ω
10 − Ground (Brake pedal position: Depressed)No continuity
CRUISE CONTROL SWITCH
18 − Ground (Control switch position: OFF)No continuity
18 − Ground (Control switch position: RESUME/ACCEL)Approx. 68.0 Ω
18 − Ground (Control switch position: SET/COAST)Approx. 198.0 Ω
18 − Ground (Control switch position: CANCEL)Approx. 418.0 Ω
14 − Ground (Ignition switch position: LOCK or ACC)No voltage
14 − Ground (Ignition switch position: ON)Battery positive voltage
15 − Ground (Constant)Battery positive voltage
1 − Ground (Constant)Battery positive voltage
16 − Ground (Brake pedal position: Released)No voltage
16 − Ground (Brake pedal position: Depressed)Battery positive voltage
20 − Ground (With ignition switch ON, Speedsensor shaft turned)Valtage changes repeatedly
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2.0 kΩ
2 − 3 (The arm is moving from the closed to open position)Approx. 0.5 to 1.8 kΩ
ANTENNA MOTOR CONTROL RELAY (Wire harness side)
3 − Ground (Constant)Battery positive voltage
5 − Ground (Ignition Switch position: LOCK)No voltage
5 − Ground (Ignition switch position: ACC)Battery positive voltage
7 − Ground (Ignition switch position: LOCK)No voltage

Downloaded from www.Manualslib.com manuals search engine DI0T6−01
ENGINE CONTROL SYSTEM Check Sheet
Customer’s Name
Driver’s Name
Data Vehicle
Brought in
License No.
Model and Model
Year
Frame No.
Engine Model
Odometer Reading
km
miles
Problem Symptoms
Engine does
not Start
Difficult to
Start
Poor Idling
Poor
Driveability
Engine Stall
Others
Engine does not crankNo initial combustionNo complete combustion
Engine cranks slowly
Other
Incorrect first idleIdling rpm is abnormalHigh ( rpm)Low ( rpm)
Rough idling
Other
HesitationBack fireMuffler explosion (after−fire)Surging
Knocking
Other
Soon after startingAfter accelerator pedal depressed
After accelerator pedal released
During A/C operation
Shifting from N to D
Other
Datas Problem
Occurred
Problem Frequency
Condition When
Problem Occurs
Weather
Engine Operation
Engine Temp. Place Outdoor Temp.Constant
Sometimes ( times per day/month)Once only
Other
Fine
CloudyRainySnowyVarious/Other
Hot
Warm CoolCold (approx. °F/ °C)
Highway
SuburbsInner cityUphillDownhill
Rough road
Other
Cold
Warming upAfter warming upAny temp.Other
Starting
Just after starting ( min.)IdlingRacing
Driving
Constant speedAccelerationDeceleration
A/C switch ON/OFF
Other
Condition of MILRemains on Sometimes lights up Does not light up
NormalMalfunction code(s) (code )
Freezed frame data ( )
NormalMalfunction code(s) (code )
Freezed frame data ( )
Normal Mode
(Precheck)
Check Mode DTC InspectionInspector’s
Name
DI−2
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
CUSTOMER PROBLEM ANALYSIS CHECK

Downloaded from www.Manualslib.com manuals search engine DI−12
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
(b) TOYOTA Enhanced Signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.5 − 4.3 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 24.8 − 50.0 %
STARTER SIGStarter SignalCranking: ON
CTP SWClosed Throttle Position Switch SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL #1, CYL #2, CYL #3, CYL #4Abnormal revolution variation for each cylinder0 %
IGNITIONTotal number of ignition for every 1,000
revolutions0 − 2,000
EGRT GASEGR Gas Temp. Sensor ValueEGR not operating: Temp. between intake air
temp. and engine coolant temp.
EGR SYSTEMEGR System Operating ConditionIdling: OFF
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalIdling: OFF
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from lean to rich
Idling after warming up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from rich to lean
Idling after warming up: 0 − 1,000 msec.
*: If no conditions are specifically stated for ”ldling”, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

Downloaded from www.Manualslib.com manuals search engine P21242 FI7210
A00027
Atmosphere
Flange
Platinum Electrode
Solid Electrolyte
(Zirconia Element)
Platinum Electrode
Heater
Coating (Ceramic)
Exhaust GasCoverIdeal Air−Fuel Mixture
Output Voltage
Richer − Air Fuel Ratio − Leaner DI−44
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
DTC P0125 Insufficient Coolant Temp. for Closed Loop
Fuel Control
CIRCUIT DESCRIPTION
To obtain a high purification rate for the CO, HC and NOx components of the exhaust gas, a three−way
catalytic converter is used, but for the most efficient use of the three−way catalytic converter, the air−fuel
ratio must be precisely controlled so that it is always close to the stoichiometric air−fuel ratio.
The oxygen sensor has the characteristic where by its output voltage changes suddenly in the vicinity of the
stoichiometric air−fuel ratio. This is used to detect the oxygen concentration in the exhaust gas and provide
feedback to the computer for control of the air−fuel ratio.
When the air−fuel ratio becomes LEAN, the oxygen concentration in the exhaust increases and the oxygen
sensor informs the ECM of the LEAN condition (small electromotive force: 0 V).
When the air−fuel ratio is RICHER than the stoichiometric air−fuel ratio the oxygen concentration in the ex-
haust gas is reduced and the oxygen sensor informs the ECM of the RICH condition (large electromotive
force: 1 V). The ECM judges by the electromotive force from the oxygen sensor whether the air−fuel ratio
is RICH or LEAN and controls the injection time accordingly. However, if malfunction of the oxygen sensor
causes output of abnormal electromotive force, the ECM is unable to perform accurate air−fuel ratio control.
The heated oxygen sensors include a heater which heats the zirconia element. The heater is controlled by
the ECM. When the intake air volume is low (the temp. of the exhaust gas is low) current flows to the heater
to heat the sensor for accurate oxygen concentration detection.
DTC No.DTC Detecting ConditionTrouble Area
P0125
After engine is warmed up, heated oxygen sensor output
does not indicate RICH even once when conditions (a), (b),
(c) and (d) continue for at least 1.5 min.:
(a) Engine speed: 1,500 rpm or more
(b) Vehicle speed: 40 ∼ 100 km/h (25 ∼ 62 mph)
(c) Closed throttle position switch: OFF
(d) 140 sec. or more after starting engine
Open or short in heated oxygen sensor (bank 1 sensor 1)
circuit
Heated oxygen sensor (bank 1 sensor 1)
HINT:
After confirming DTC P0125 use the OBD II scan tool or TOYOTA handheld tester to confirm voltage output
of heated oxygen sensor from "CURRENT DATA".
If voltage output of heated oxygen sensor is 0 V, heated oxygen sensor circuit may be open or short.
DI0TJ−02

Downloaded from www.Manualslib.com manuals search engine P19893
ECM
Throttle Body
Throttle
ValveCheck
Valve
(for A/T)
EGR Vacuum Modulator
VSVEGR
Valve
P19921
R/B No.2
IG Switch
E7 E7
(M/T)(A/T)
E01
E1 ECM
E2 EGR
THG
E6 E6
E6 E6
622
14 3
99 1
BR−B G−WP
2
2
1 9 9
EA
W−R W−R
5 V
IE1W−REA1
W−B
2
3
22 22
2
25 B−W
EFIEFI Relay
VSV for EGR
EGR Gas
Temp. Sensor B−Y
EA1
4B−Y
1C17
1A3
W−R IGN
J/B
No.1
FromFrom Battery
5
1 DI−72
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
DTC P0401 Exhaust Gas Recirculation Flow Insufficient
Detected
CIRCUIT DESCRIPTION
The EGR system recirculates exhaust gas, which is controlled to the proper quantity to suit the driving condi-
tions, into the intake air mixture to slow down combustion, reduce the combustion temp. and reduce NOx
emissions. The amount of EGR is regulated by the EGR vacuum modulator according to the engine load.
If even one of the following conditions is fulfilled, the VSV is
turned ON by a signal from the ECM.
This results in atmospheric air acting on the EGR valve, closing
the EGR valve and shutting off the exhaust gas (EGR cut−off).
Under the following conditions, EGR is cut to maintain driveabil-
ity:
Before the engine is warmed up
During deceleration (throttle valve closed)
Light engine load (amount of intake air very small)
Engine racing
DTC No.DTC Detecting ConditionTrouble Area
P0401
After engine is warmed up and run at 80 km/h (50 mph)
for 3 to 5 min., EGR gas temp. sensor value does not exceed
35°C (95°F) above ambient air temp.
(2 trip detection logic)EGR valve stuck closed
Short in VSV circuit for EGR
Open in EGR gas temp. sensor circuit
EGR hose disconnected
ECM
WIRING DIAGRAM
DI0TU−03