1996 TOYOTA T100 fuel cap

Downloaded from www.Manualslib.com manuals search engine MA004−03
P08488
Back Front
− MAINTENANCEENGINE
MA−5
40 Author: Date:
1996 TOYOTA T100 (RM449U)
ENGINE
INSPECTION
HINT:
Inspect these items when the engine is cold.
1. (5VZ−FE ENGINE)
REPLACE TIMING BELT
(See page EM−11 )
2. INSPECT DRIVE BELTS
GENERATOR:
(3RZ−FE: See page CH−2)
(5VZ−FE: See page CH−1)
PS:
(3RZ−FE: See page SR−3)
(5VZ−FE: See page SR−3)
A/C:
(3RZ−FE: See page AC−14)
(5VZ−FE: See page AC−14)
3. REPLACE SPARK PLUGS
(3RZ−FE: See page IG−1)
(5VZ−FE: See page IG−1)
4. INSPECT AIR FILTER
(a) Visually check that the air cleaner element is not exces-
sively dirty, damaged or oily.
HINT:
Oiliness may indicate a stuck PCV valve.
If necessary, replace the air cleaner element.
(b) Clean the element with compressed air.
First blow from back side thoroughly, then blow off the
front side of the element.
5. REPLACE AIR FILTER
Replace the used air cleaner element with a new one.
6. REPLACE ENGINE OIL AND OIL FILTER
(3RZ−FE: See page LU−3)
(5VZ−FE: See page LU−3)
7. REPLACE ENGINE COOLANT
(3RZ−FE: See page CO−2)
(5VZ−FE: See page CO−
2)
8. CALIFORNIA, MASSACHUSETTS, MAIN, VERMONT,
RHODE ISLAND and NEW HAMPSHIRE:
INSPECT CHARCOAL CANISTER
(3RZ−FE: See page EC−5)
(5VZ−FE: See page EC−5)
9. REPLACE GASKET IN FUEL TANK CAP
(3RZ−FE: See page EC−5)
(5VZ−FE: See page EC−5)

Downloaded from www.Manualslib.com manuals search engine SS093−02
− SERVICE SPECIFICATIONSENGINE MECHANICAL (3RZ−FE)
SS−7
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Throttle body x Air intake chamber2020014
Spark plug x Cylinder head1920014
Cylinder head x Cylinder block 1st
2nd
3rd39
Turn 90°
Turn 90°
40029
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head15.516012
Camshaft timing gear x Camshaft73.575054
Distributor gear x Camshaft4646534
Chain tensioner x Cylinder head2121015
Engine hanger x Cylinder head4242030
Exhaust manifold x Cylinder head4950036
Heat insulator x Exhaust manifold5.55548 in.·lbf
Front exhaust pipe x Exhaust manifold6263046
No.1 support bracket x Transmission3940029
No.1 support bracket clamp bolt1919514
Front exhaust pipe x TWC3940029
Intake manifold x Cylinder head2930022
Delivery pipe x Intake manifold2121015
Fuel inlet tube x Fuel filter2930022
Fuel inlet tube x Delivery pipe2930022
EGR valve x Air intake chamber, EGR pipe1919514
EGR vacuum modulator x Air intake chamber8.58574 in.·lbf
EGR pipe x Exhaust manifold2020015
EGR pipe x Cylinder head1818514
Cylinder head rear cover x Cylinder head13.513510
Water outlet x Cylinder head2020014
PS pump bracket x Cylinder head2020014
PS pump bracket x PS pump5859043
PS pump x PS pump pulley4344032
PS pump idler pulley x Cylinder head2020014
Balance shaft drive gear x Balance shaft2525018
No.2 chain tensioner, No.3 vibration damper x Cylinder block1818513
No.2 vibration damper x Cylinder block2727020
No.1 vibration damper x Cylinder block1818513
No.1 timing chain tensioner slipper x Cylinder block2727020
Timing chain cover x Cylinder block Bolt A
Bolt B
Bolt C
Nut D20
24.5
44
20200
250
440
20014
18
32
14
Timing chain cover mounting bolt1818513
No.1 water bypass pipe mounting nut2020014
Crankshaft pulley x Crankshaft2602,650193
No.2 and No.3 crankshaft pulley x Crankshaft pulley2525018

Downloaded from www.Manualslib.com manuals search engine SS−8
− SERVICE SPECIFICATIONSENGINE MECHANICAL (3RZ−FE)
1996 TOYOTA T100 (RM449U) Oil strainer x Cylinder block
1818513
Oil pan x Cylinder block12.51309
Crankshaft position sensor x Timing chain cover8.58574 in.·lbf
Generator bracket x Cylinder block74.576055
Generator bracket x Timing chain cover1818513
Generator adjusting bar x Timing chain cover63.565047
A/C compressor bracket x Cylinder block4444032
A/C compressor x A/C compressor bracket2525018
Water pump pulley x Water pump2121016
Connecting rod cap x Connecting rod 1st
2nd45
Turn 90°46033
Main bearing cap x Cylinder block 1st
2nd39
Turn 90°40029
No.1 balance shaft x Timing gear3636526
No.2 balance shaft x Timing sprocket3636526
Balance shaft x Cylinder block1818513.4
Rear oil seal retainer x Cylinder block13.51359.7
RH, LH engine mounting bracket x Cylinder block4545034
Oil dipstick guide x LH engine mounting bracket2020014
Oil filter bracket union, Engine coolant drain plug x Cylinder block2525018
Oil filter bracket x Cylinder block2829021
Water bypass pipe x Cylinder block2020014
Knock sensor x Cylinder block3738027
Fuel filter x Cylinder block2020014
Rear end plate x Cylinder block1818513
Rear end plate x Water bypass pipe2020014
Flywheel x Crankshaft 1st
2nd26.5
Turn 90°27019
Front crossmember x Engine rear mounting bracket2526019
Front exhaust pipe clamp x Exhaust manifold6263046
Exhaust support bracket x Transmission3940029
Front exhaust pipe clamp1919514
Front exhaust pipe x TWC3940029
Engine rear mounting bracket x Engine rear mounting insulator1818313
Engine front mounting insulator x Frame3838728
Clutch release cylinder bracket x Transmission3940029
Clutch release cylinder x Transmission131309
Stabilizer bar bracket mounting bolt3030622
Stabilizer bar x Lower suspension arm131309
Intake air connector x Cylinder head1818513
Radiator x Body1818513

Downloaded from www.Manualslib.com manuals search engine SS097−02
SS−18
− SERVICE SPECIFICATIONSMFI (3RZ−FE)
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Fuel line (Union bolt type)2930022
Fuel line (Flare nut type)3031022
Fuel pump bracket assembly x Fuel tank3.94035 in.·lbf
Fuel filter x Cylinder block2020015
Fuel pressure regulator x Delivery pipe8.89078 in.·lbf
Delivery pipe x Cylinder head2121015
Fuel inlet tube x Fuel filter2930022
Fuel inlet tube x Delivery pipe2930022
Air intake chamber x Intake manifold2121015
Throttle body x Air intake chamber2020014
Fuel evaporation tube x Fuel tank1.51513 in.·lbf
Fuel tank filler pipe x Fuel tank3.53531 in.·lbf
Fuel inlet pipe x Body5.45547 in.·lbf
Fuel tank band x Body3940029
MAF meter x Air cleaner cap101007
ECT sensor x Cylinder head2020014
Knock sensor x Cylinder block4445033

Downloaded from www.Manualslib.com manuals search engine SS00V−11
SS−20
− SERVICE SPECIFICATIONSSFI (5VZ−FE)
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Fuel line (Union bolt type)34.335025
Fuel line (Flare nut type)34.335025
Fuel line (Flare nut type) using SST2828521
No. 2 timing belt cover x No. 3 timing belt cover99080 in.·lbf
Fuel inlet pipe x Intake manifold88071 in.·lbf
Delivery pipe x Intake manifold1313010
Fuel pump bracket assembly x Fuel tank3.94035 in.·lbf
Fuel tank band x Body4344032
Fuel tank filler pipe x Fuel tank3.94035 in.·lbf
Fuel evaporation vent tube x Fuel tank1.51513 in.·lbf
Fuel pressure regulator x LH delivery pipe88071 in.·lbf
MAF meter x Air cleaner cap6.97261 in.·lbf
VSV assembly x Air intake connector88071 in.·lbf
A/C idle−up valve x Intake air connector2020014
ECT sensor x Intake manifold2020014
Knock sensor x Cylinder block3940029
EGR gas temperature sensor x EGR valve2020014
Heated oxygen sensor x Front exhaust pipe, Center exhaust pipe2020014

Downloaded from www.Manualslib.com manuals search engine SS03A−03
− SERVICE SPECIFICATIONSBODY ELECTRICAL
SS−77
251 Author: Date:
1996 TOYOTA T100 (RM449U)
BODY ELECTRICAL
SERVICE DATA
DAYTIME RUNNING LIGHT MAIN RELAY (Wire Harness Side)
2 − Ground (Ignition Switch LOCK or ACC)No voltage
2 − Ground (Ignition Switch ON or START)Battery positive voltage
6 − Ground (Constant)Battery positive voltage
11 − Ground (Engine Stop)No voltage
11 − Ground (Engine Running)Battery positive voltage
DAYTIME RUNNING LIGHT MAIN RELAY (Connector connected)
17 − Ground (Headlight dimmer switch LOW beam)No voltage
17 − Ground (Headlight dimmer switch HIGH beam or Flash)Battery positive voltage
TURN SIGNAL FLASHER
Flashes/ Minute60 − 120
SPEEDOMETER (Using a speedmeter tester)
Standard indication (mph)Allowable range (mph)
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
12011 8 − 132
Standard indication (km/h)Allowable range (km/h)
2017 − 24
4038 − 46
6057.5 − 67
8077 − 88
10096 − 109
12011 5 − 130
140134 − 151.5
160153 − 173
TACHOMETER (On−Vehicle) / DC 13.5 V 20 °C at (68 °F)
Standard indicationAllowable range
700610 − 750
3,0002,850 − 3,150
5,0004,850 − 5,150
7,0006,790 − 7,210
VOLT GAUGEResistance (Ω)
A − BApprox. 347.0 Ω
FUEL RECEIVER GAUGE (w/ Tachometer)Resistance (Ω)
A − BApprox. 137.0 Ω
A − CApprox. 123.0 Ω
B − CApprox. 260.0 Ω
FUEL RECEIVER GAUGE (w/o Tachometer)Resistance (Ω)
A − BApprox. 150.0 Ω
A − CApprox. 80.0 Ω

Downloaded from www.Manualslib.com manuals search engine SS−78
− SERVICE SPECIFICATIONSBODY ELECTRICAL
252 Author: Date:
1996 TOYOTA T100 (RM449U)B − C
Approx. 55.0 Ω
FUEL SENDER GAUGE
Float position mm (in.)Resistance (Ω)
F: Approx. 95 mmApprox. 3.0 Ω
1/2: Approx. 188.0 mmApprox. 32.5 Ω
E: Approx. 283.0 mmApprox. 110.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ Tachometer)Resistance (Ω)
A − BApprox. 150.0 Ω
A − CApprox. 54.0 Ω
B − CApprox. 138.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ o Tachometer)
A − BApprox. 25.0 Ω
OIL PRESSURE RECEIVER GAUGE
A − BApprox. 25.0 Ω
DOOR LOCK CONTROL RELAY (Wire Harness Side)
2 − Ground (Constant)Battery positive voltage
8 − Ground (Ignition Switch LOCK or ACC)No voltage
8 − Ground (Ignition Switch ON)Battery positive voltage
13 − Ground (Key unlock warning switch OFF (Ignition key removed))No voltage
13 − Ground (Key unlock warning switch ON (Ignition key set))Battery positive voltage
CRUISE CONTROL ECU (wire harness side)
24 − 26 (constant)Approx. 2.0 kΩ
25 − 26 (Actuator arm turned)Resistance change even
10 − Ground (Brake pedal position: Released)Approx. 38.0 Ω
10 − Ground (Brake pedal position: Depressed)No continuity
CRUISE CONTROL SWITCH
18 − Ground (Control switch position: OFF)No continuity
18 − Ground (Control switch position: RESUME/ACCEL)Approx. 68.0 Ω
18 − Ground (Control switch position: SET/COAST)Approx. 198.0 Ω
18 − Ground (Control switch position: CANCEL)Approx. 418.0 Ω
14 − Ground (Ignition switch position: LOCK or ACC)No voltage
14 − Ground (Ignition switch position: ON)Battery positive voltage
15 − Ground (Constant)Battery positive voltage
1 − Ground (Constant)Battery positive voltage
16 − Ground (Brake pedal position: Released)No voltage
16 − Ground (Brake pedal position: Depressed)Battery positive voltage
20 − Ground (With ignition switch ON, Speedsensor shaft turned)Valtage changes repeatedly
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2.0 kΩ
2 − 3 (The arm is moving from the closed to open position)Approx. 0.5 to 1.8 kΩ
ANTENNA MOTOR CONTROL RELAY (Wire harness side)
3 − Ground (Constant)Battery positive voltage
5 − Ground (Ignition Switch position: LOCK)No voltage
5 − Ground (Ignition switch position: ACC)Battery positive voltage
7 − Ground (Ignition switch position: LOCK)No voltage

Downloaded from www.Manualslib.com manuals search engine FI4741
(fig.1)
Acceptable
Resistance kΩ
− 20 0 20 40 60 80 100
(− 4) 32 68 104 140 176 212 30
20
10
5
3
2
1
0.5
0.3
0.2
0.1
Temp.°C (F°)
− DIAGNOSTICSENGINE (3RZ−FE)
DI−27
1996 TOYOTA T100 (RM449U)
DTC P0110 Intake Air Temp. Circuit Malfunction
CIRCUIT DESCRIPTION
The intake air temp. sensor is built into the air cleaner cap and
sensors the intake air temp.
A thermistor built in the sensor changes the resistance value
according to the intake air temp. The lower the intake air temp.,
the greater the thermistor resistance value, and the higher the
intake air temp., the lower the thermistor resistance value (See
fig.1).
The intake air temp. sensor is connected to the ECM (See be-
low). The 5 V power source voltage in the ECM is applied to the
intake air temp. sensor from the terminal THA via a resistor R.
That is, the resistor R and the intake air temp. sensor are con-
nected in series. When the resistance value of the intake air
temp. sensor changes in accordance with changes in the intake
air temp., the potential at terminal THA also changes. Based on
this signal, the ECM increases the fuel injection volume to im-
prove driveability during cold engine operation.
If the ECM detects the DTC ”P0110”, it operates the fail safe
function in which the intake air temp. is assumed to be 20°C
(68°F).
DTC No.DTC Detecting ConditionTrouble Area
P0110Open or short in intake air temp. sensor circuit
Open or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM
HINT:
After confirming DTC P110 use the OBD II scan tool or TOYOTA nand−held tester to confirm the intake air
temp. from ”CURRENT DATA”.
Temp. DisplayedMalfunction
− 40°C (− 40°F)Open circuit
140°C (284°F) or moreShort circuit
DI0TE−03