1996 TOYOTA T100 battery replacement

Downloaded from www.Manualslib.com manuals search engine IN02H−03
BO4111
Negative Cable
− INTRODUCTIONFOR ALL OF VEHICLES
IN−9
9 Author: Date:
1996 TOYOTA T100 (RM449U)
FOR ALL OF VEHICLES
PRECAUTION
1. FOR VEHICLES EQUIPPED WITH SRS AIRBAG
(a) The TOYOTA T100 is equipped with an SRS (Supple-
mental Restraint System), such as the driver airbag.
Failure to carry out service operations in the correct se-
quence could cause the supplemental restraint system to
unexpectedly deploy during servicing, possibly leading to
a serious accident.
Further, if a mistake is made in servicing the supplemental
restraint system, it is possible the SRS may fail to operate
when required. Before servicing (including removal or
installation of parts, inspection or replacement), be sure
to read the following items carefully, then follow the cor-
rect procedure described in this manual.
(b) GENERAL NOTICE
(1) Malfunction symptoms of the supplemental re-
straint system are difficult to confirm, so the diag-
nostic trouble codes become the most important
source of information when troubleshooting. When
troubleshooting the supplemental restraint system,
always inspect the diagnostic trouble codes before
disconnecting the battery (See page DI−365).
(2) Work must be started after 90 seconds from the
time the ignition switch is turned to the ”LOCK” posi-
tion and the negative (−) terminal cable is discon-
nected from the battery.
(The supplemental restraint system is equipped
with a back−up power source so that if work is
started within 90 seconds of disconnecting the neg-
ative (−) terminal cable from the battery, the SRS
may deploy.)
When the negative (−) terminal cable is discon-
nected from the battery, memory of the clock and
audio systems will be cancelled. So before starting
work, make a record of the contents memorized by
the each memory system. Then when work is fin-
ished, reset the clock and audio systems as before.
To avoid erasing the memory of each memory sys-
tem, never use a back−up power supply from out-
side the vehicle.
(3) Even in cases of a minor collision where the SRS
does not deploy, the steering wheel pad should be
inspected (See page RS−9).

Downloaded from www.Manualslib.com manuals search engine RS03H−01
− SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS−1
1768 Author: Date:
1996 TOYOTA T100 (RM449U)
SRS AIRBAG
PRECAUTION
NOTICE:
The TOYOTA T100 is equipped with SRS, which comprises a driver airbag. Failure to carry out
service operations in the correct sequence could cause the SRS to unexpectedly deploy during
servicing, possibly leading to a serious accident. Further, if a mistake is made in servicing the
SRS, it is possible that the SRS may fail to operate when required. Before performing servicing
(including removal or installation of parts, inspection or replacement), be sure to read the fol-
lowing items carefully, then follow the correct procedures described in the repair manual.
Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most impor-
tant source of information when troubleshooting. When troubleshooting the SRS, always in-
spect the DTCs before disconnecting the battery.
Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, air-
bag sensor assembly and front airbag sensor should be inspected (See page RS−9, RS−23 and
RS−28).
Never use SRS parts from another vehicle. When replacing parts, replace them with new parts.
Never disassemble and repair the steering wheel pad, airbag sensor assembly or front airbag
sensor in order to reuse it.
If the steering wheel pad, airbag sensor assembly or front airbag sensor has been dropped, or
if there are cracks, dents or other defects in the case, bracket or connector, replace them with
new ones.
Use a volt/ohmmeter with high impedance ( 10 kΩ/V minimum) for troubleshooting the system’s
electrical circuits.
Information labels are attached to the periphery of the SRS components. Follow the instruc-
tions on the notices.
After work on the SRS is completed, perform the SRS warning light check or SRS side airbag
warning light check (See page DI−365).
If the vehicle is equipped with a mobile communication system, refer to the precaution in the
IN section.
CAUTION:
Work must be started after 90 seconds from when the ignition switch is turned to the ”LOCK”
position and the negative (−) terminal cable is disconnected from the battery.
(The SRS is equipped with a back−up power source so that if work is started within 90 seconds
from disconnecting the negative (−) terminal cable of the battery, the SRS may be deployed.)
When the negative (−) terminal cable is disconnected from the battery, the memory of the clock
and audio system will be canceled. So before starting work, make a record of the contents mem-
orized in the audio memory system. When work is finished, reset the audio systems as they
were before and adjust the clock. To avoid erasing the memory in each memory system, never
use a back− up power supply from outside the vehicle.
Before repairs, remove the airbag sensor if shocks are likely to be applied to the sensor during
repairs.
Do not expose the steering wheel pad, airbag sensor assembly or front airbag sensor directly
to hot air or flames.

Downloaded from www.Manualslib.com manuals search engine BE01E−07
− BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE−1
1801 Author: Date:
1996 TOYOTA T100 (RM449U)
BODY ELECTRICAL SYSTEM
PRECAUTION
Take care to observe the following precautions when performing inspections or removal and replacement
of body electrical related parts.
1. LIGHTING SYSTEM
Halogen bulbs have pressurized gas inside and require special handling.
They can burst or scatter if scratched or dropped. Hold a bulb only by its plastic or metal case.
Don’t touch the glass part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The TOYOTA T100 is equipped with an SRS (Supplemental Restraint System) such as the driver airbag.
Failure to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy
during servicing, possibly leading to a serious accident. Before servicing (including removal or installation
of parts, inspection or replacement), be sure to read the precautionary notices in the RS section.
3. AUDIO SYSTEM
If the battery negative (−) terminal is disconnected, the preset AM, FM 1 and FM 2 stations stored in
memory are erased, so be sure to note the stations and reset them after the battery terminal is recon-
nected.
If the battery negative (−) terminal is disconnected, the ”ANTI−THEFT SYSTEM” will operate when the
terminal is reconnected, but the radio, tape player and CD player will not operate. Be sure to input the
correct ID number so that the radio, tape player and CD player can be operated again.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to precautions in the IN section.

Downloaded from www.Manualslib.com manuals search engine BE1PL−02
BE4671
Antenna Nut
BE5781
BE5780
BE4674
Twist BE−82
− BODY ELECTRICALANTENNA
1996 TOYOTA T100 (RM449U)
REPLACEMENT
1. REMOVE ANTENNA ROD
HINT:
Perform this operation with negative (−) cable connected to the
battery terminal.
(a) Turn the ignition switch to ”LOCK” position.
(b) Remove the antenna nut.
(c) Press the ”AM” buttons on the radio receiver, and simulta-
neously turn the ignition switch to ”ACC” position.
HINT:
The rod will extend fully and be released from the motor
antenna.
After removing the antenna rod, leave the ignition switch
as ”ACC”.
NOTICE:
To prevent body damage when the antenna rod is released,
hold the rod while it comes out.
2. INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.
HINT:
When inserting the cable, the teeth on the cable must face to-
ward the front of the vehicle.
(b) Wind the cable to retract the rod by turning the ignition
switch to ”LOCK” position.
HINT:
If the ignition switch is already in ”LOCK” position, perform
step 1 (c) first, then turn the ignition switch to ”ACC” posi-
tion.
In case the cable is not wound, twist it as shown in the il-
lustration.
Even if the rod has not retracted fully, install the antenna
nut and inspect the antenna rod operation. It will finally re-
tract fully.
(c) Inspect the antenna rod operation by pushing the radio
wave band select buttons.