1996 TOYOTA T100 check engine light

Downloaded from www.Manualslib.com manuals search engine Q07663
1
2
DI−314
− DIAGNOSTICSAUTOMATIC TRANSMISSION
1996 TOYOTA T100 (RM449U)
3 Check harness and connector between O/D OFF indicator light and ECM (See
page IN−26).
NG Repair or replace harness or connector.
OK
Check O/D main switch.
4 Check O/D main switch.
PREPARATION:
Disconnect the O/D main switch connector.
CHECK:
Check continuity resistance between terminal 1 and 2 of O/D
main switch connector.
OK:
O/D main switch conditionSpecified condition
ON (Pushed in)No continuity
OFF (Pushed once agin)Continuity
NG Replace O/D main switch.
OK
Check and replace the combination meter
(See page BE−38).

Downloaded from www.Manualslib.com manuals search engine Q07663
1
2
− DIAGNOSTICSAUTOMATIC TRANSMISSION
DI−315
1996 TOYOTA T100 (RM449U)
O/D OFF indicator light remains ON:
1 Check O/D main switch.
PREPARATION:
Disconnect the O/D main switch connector.
CHECK:
Check continuity between terminals 1 and 2 of O/D main switch
connector.
OK:
O/D main switchSpecified condition
ONNo continuity
OFFContinuity
NG Replace O/D main switch.
OK
2 Check harness and connector between O/D OFF indicator light and O/D main
switch, O/D OFF indicator light and ECM (See page IN−26).
NG Repair or replace harness or connector.
OK
Check and replace ECM.

Downloaded from www.Manualslib.com manuals search engine D11000
− DIAGNOSTICSAUTOMATIC TRANSMISSION
DI−317
1996 TOYOTA T100 (RM449U)
INSPECTION PROCEDURE
1 Check operation of stop light.
CHECK:
Check if the stop lights go on and off normally when the brake pedal is operated and released.
NG Check and repair stop light circuit.
OK
2 Check STP signal.
When using OBD II scan tool or TOYOTA hand−held tester:
PREPARATION:
(a) Connect an OBD II scan tool or TOYOTA hand−held tes-
ter to the DLC3.
(b) Turn the ignition switch ON and OBD II scan tool or TOY-
OTA hand−held tester main switch ON.
CHECK:
Read the STP signal on the TOYOTA hand−held tester.
OK:
Brake PedalSTP Signal
DepressedON
ReleaseOFF
When not using OBD II scan tool or TOYOTA hand−held tes-
ter:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Check the voltage between terminal B/K of the ECM connector
and body ground.
OK:
Brake PedalVoltage
Depressed7.5 − 14 V
ReleaseBelow 1.5 V

Downloaded from www.Manualslib.com manuals search engine DI−318
− DIAGNOSTICSAUTOMATIC TRANSMISSION
1996 TOYOTA T100 (RM449U)
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−282).
NG
3 Check harness and connector between stop light switch and ECM (See page
IN−26).
NG Repair or replace harness or connector.
OK
Check and replace ECM.

Downloaded from www.Manualslib.com manuals search engine DI0ZI−01
ABS Check SheetInspector ’s
Name:
Customer ’s Name
Date Vehicle
Brought InRegistration YearRegistration No.
Frame No.
Odometer Reading/ /
/ /
Date Problem First Occurred
Frequency Problem Occurs/ /
ContinuousIntermittent ( times a day)
ABS does not operate.
ABS does not operate efficiently.
ABS Warning Light
AbnormalRemains ONDoes not Light Up
DTC Check1st Time
2nd TimeNormal Code
Malfunction Code (Code )
Normal CodeMalfunction Code (Code )
Symptomskm
miles DI−320
− DIAGNOSTICSANTI−LOCK BRAKE SYSTEM
1996 TOYOTA T100 (RM449U)
CUSTOMER PROBLEM ANALYSIS CHECK

Downloaded from www.Manualslib.com manuals search engine R12019
DI0ZM−03
A00778DLC1 E
1Tc
F00006
DLC1Short Pin
R01346
Normal Code
0.25 sec.
0.25 sec. 2 sec.
ON
OFF
ON
OFF0.5 sec.0.5 sec.
Code 11 and 21
4 sec.1.5 sec.
2.5 sec.
Code 11 Code 21
− DIAGNOSTICSANTI−LOCK BRAKE SYSTEM
DI−321
1996 TOYOTA T100 (RM449U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Check the indicator light.
When the ignition switch is turned ON, check that the ABS
warning light goes on for 3 seconds.
HINT:
If the indicator check result is not normal, proceed to trouble-
shooting for the ABS warning light circuit (See page DI−354).
(b) Check the DTC.
(1) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843−18020
(2) Disconnect the short pin from the DLC1.
(3) Turn the ignition switch ON.
(4) Read the DTC from the ABS warning light on the
combination meter.
HINT:
If no code appears, inspect the diagnostic circuit or ABS
warning light circuit (See page DI−354 or DI−358).
As an example, the blinking patterns for normal code and
codes 11 and 21 are shown on the left.
(5) Code are explained in the code table on page
DI−326.
(6) After completing the check, disconnect terminals Tc
and E
1, and turn off the display.
If 2 or more malfunctions are indicated at the same time the low-
est numbered DTC will be displayed 1st.

Downloaded from www.Manualslib.com manuals search engine BR3890
F00006DLC1Short Pin
N09348
TOYOTA
hand−held tester
TOYOTA
brake−out−box ECU
A00778DLC1 E
1Tc
Ts DI−322
− DIAGNOSTICSANTI−LOCK BRAKE SYSTEM
1996 TOYOTA T100 (RM449U)
(c) Clear the DTC.
(1) Using SST, connect terminals Tc and E
1 of the
DLC1 and remove the short pin from the DLC1.
SST 09843−18020
(2) Turn the ignition switch ON.
(3) Clear the DTC stored in ECU by depressing the
brake pedal 8 or more times within 3 seconds.
(4) Check that the warning light shows the normal
code.
(5) Remove the SST from the terminals of the DLC1.
SST 09843−18020
(6) Connect the short pin to the DLC1.
HINT:
Cancellation can also be done by removing the ECU−B fuse,
but in this case, other memory systems will also be cancelled
out.
(d) Using TOYOTA brake−out−box and TOYOTA hand−held
tester, measure the ECU terminal value.
(1) Hook up the TOYOTA hand−held tester and
TOYOTA break−out−box to the vehicle.
(2) Read the ECU input/output values by following the
prompts on the tester screen.
HINT:
TOYOTA hand−held tester has a ”Snapshot” function. This re-
cords the measured values and is effective in the diagnosis of
intermittent problems.
Please refer to the TOYOTA hand−held tester/TOYOTA break−
out−box operator’s manual for further details.
2. SPEED SENSOR SIGNAL AND DECELERATION SEN-
SOR CHECK
(a) Check the speed sensor signal.
(1) Turn the ignition switch OFF.
(2) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(3) Start the engine.

Downloaded from www.Manualslib.com manuals search engine BR3904
0.13 sec. 0.13 sec.
ON
OFF
BR3893
Malfunction Code (Example Code 72, 76)
7
26
7
ON
OFF
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.1.5 sec. 2.5 sec.4 sec.
Repeat
A00778DLC1 E
1
Ts
− DIAGNOSTICSANTI−LOCK BRAKE SYSTEM
DI−323
1996 TOYOTA T100 (RM449U)
(4) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−354).
(5) Drive vehicle straight forward.
HINT:
Drive vehicle faster than 45 km/h (28 mph) for several seconds.
(6) Stop the vehicle.
(7) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843−18020
(8) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC on page DI−326.
If every sensor is normal, a normal code is output (A cycle
of 0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction are indicated at the same time,
the lowest numbered code will be displayed 1st.
(9) After doing the check, disconnect terminals Ts and
E
1, Tc and E1 of the DLC1, and ignition switch
turned OFF.
(b) Check the deceleration sensor detection point.
(1) Turn the ignition switch OFF.
(2) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(3) Start the engine.