1996 TOYOTA T100 brake sensor

Downloaded from www.Manualslib.com manuals search engine BR0A4−03
BR−66
− BRAKEFRONT SPEED SENSOR
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is reverse in the order of removal (See page BR−65).
AFTER INSTALLATION, CHECK SPEED SENSOR SIGNAL (See page DI−341)

Downloaded from www.Manualslib.com manuals search engine BR0A5−04
R14755
Speed Sensor
Sensor Rotor
N·m (kgf·cm, ft·lbf) : Specified torque
13 (130, 9)
8.0 (82, 71 in.·lbf)
− BRAKEREAR SPEED SENSOR
BR−67
1672 Author: Date:
1996 TOYOTA T100 (RM449U)
REAR SPEED SENSOR
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine BR0A6−01
R12233
BR−68
− BRAKEREAR SPEED SENSOR
1996 TOYOTA T100 (RM449U)
REMOVAL
1. DISCONNECT SPEED SENSOR CONNECTOR
2. REMOVE SPEED SENSOR
(a) Remove the clamp bolt, the clamp nut and the 5 clips
holding the sensor wire harness from the axle and the fuel
tank.
HINT:
When installing the rear sensor wire harness, never use
the removed resin clips, which are service parts.
When replacing clips, set up new resin clips at the same
angle of the removed resin clips.
When removing a resin clip, take care so that the remov-
ing tool is not caught on the grommet or wire.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(b) Remove the speed sensor from the axle carrier.
Torque: 8.0 N·m (82 kgf·cm, 71 in.·lbf)

Downloaded from www.Manualslib.com manuals search engine BR0A7−03
− BRAKEREAR SPEED SENSOR
BR−69
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page BR−68).
AFTER INSTALLATION, CHECK SPEED SENSOR SIGNAL (See page DI−341)

Downloaded from www.Manualslib.com manuals search engine − BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE−7
1996 TOYOTA T100 (RM449U) A/T Oil temperature warning indicator light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. A/T Oil Temperature Sensor
4. Wire Harness−
BE−36
BE−38
−
SRS warning light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. Center Airbag Sensor Assembly
4. Wire Harness−
BE−36
DI−372
−
Malfunction indicator does not light up
1. Bulb
2. ECM
3. Wire Harness−
−
−
−
Seat belt warning light does not light up
1. Bulb
2. Integration Relay
3. Wiring Harness−
−
−
Discharge warning light does not light up
1. IGN Fuse (Junction Block No.1)
2. Bulb
3. Wire Harness
4. Generator−
−
−
−
Brake warning light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. Parking Brake Switch
4. Brake Fluid Level Warning Switch−
BE−36
BE−38
BE−38
COMBINATION METER
Indicator Lights:
SymptomSuspect AreaSee page
O/D OFF indicator light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. O/D OFF Switch
4. Wire Harness−
BE−36
DI−311
−
High beam indicator light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. Wire Harness
4. Headlight System−
BE−36
−
BE−2
Turn indicator light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. Wire Harness
4. Turn Signal and Hazard Warning System−
BE−36
−
BE−2
Shift indicator lights do not light up (ALL)
1. Bulb
2. Combination Meter Wiring Circuit
3. PNP Switch
4. Wire Harness−
BE−36
DI−306
−
Shift indicator lights do not light up (L, 2, D)
1. Bulb
2. Combination Meter Wiring Circuit
3. PNP Switch
4. Light Control Rheostat
5. Wire Harness−
BE−36
DI−306
BE−38
−
Only one shift indicator does not light up1. Bulb
2. Combination Meter Wiring Circuit−
BE−36