1996 TOYOTA T100 battery

Downloaded from www.Manualslib.com manuals search engine N15388
LH
Lock
Unlock
RH
Lock
Unlock
Z04374
Z04375
Z04376
BE−52
− BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
1996 TOYOTA T100 (RM449U)
3. INSPECT DOOR KEY LOCK AND UNLOCK SWITCH
CONTINUITY
LH:
Switch positionTester connectionSpecified condition
LOCK5 − 6Continuity
OFF−No continuity
UNLOCK1 − 5Continuity
If continuity is not as specified, replace the switch.
RH:
Switch positionTester connectionSpecified condition
LOCK8 − 7Continuity
OFF−No continuity
UNLOCK4 − 8Continuity
If continuity is not as specified, replace the switch.
4. INSPECT DRIVER’S DOOR LOCK MOTOR OPERA-
TION
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative (−) lead to terminal 7, check that the
door lock link moves to UNLOCK position.
(b) Remove the polarity, check that the door lock link moves
to LOCK position.
If operation is not as specified, replace the door lock assembly.
5. INSPECT PASSENGER’S DOOR LOCK MOTOR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (−) lead to terminal 6, check that the
door lock moves to UNLOCK position.

Downloaded from www.Manualslib.com manuals search engine Z14871
Unlock
16
BE2595 N02970
BE−54
− BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
1996 TOYOTA T100 (RM449U) 7 − Ground
Passenger’s door courtesy switch OFF
(Door closed)No continuity
7 − GroundPassenger’s door courtesy switch ON
(Door opened)Continuity
9 − GroundDriver’s door lock switch UNLOCKContinuity
9 − GroundDriver’s door lock switch LOCKNo continuity
10 − GroundDriver’s key lock and unlock switch Lock or OFFNo countinuity
10 − GroundDriver’s key lock and unlock switch UNLOCKCountinuity
11 − GroundConstantContinuity
12 − GroundPassenger’s door lock switch UNLOCKContinuity
12 − GroundPassenger’s door lock switch LOCKNo continuity
14 − GroundDriver’s door courtesy switch OFF (Door closed)No continuity
14 − GroundDriver’s door courtesy switch ON (Door opened)Continuity
2 − GroundConstantBattery positive voltage
8 − GroundIgnition switch LOCK or ACCNo voltage
8 − GroundIgnition switch ONBattery positive voltage
13 − GroundKey unlock warning switch OFF
(Ignition key removed)No voltage
13 − GroundKey unlock warning switch ON (Ignition key set)Battery positive voltage
If circuit is as specified, inspect the door lock signal and key−off
power window signal.
9. Door Lock Signal:
INSPECT DOOR LOCK CONTROL RELAY
HINT:
When the relay circuit is as specified, inspect the door lock sig-
nal.
(a) Connect the connector to the relay.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 1 and the negative (−) lead to terminal 6.
(c) Set the door lock control switch to UNLOCK, check that
the voltage rises from 0 V to battery positive voltage for
approximately 0.2 seconds.

Downloaded from www.Manualslib.com manuals search engine Z14872
Lock
16
BE2595 N02427
I02177
(c) Close(d) Open
Z08642
5
11
BE2886 N03190R
− BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
BE−55
1996 TOYOTA T100 (RM449U)
(d) Reverse the polarity of the voltmeter leads.
(e) Set the door lock control switch to LOCK, check that the
voltage rises from 0 V to battery positive voltage for
approximately 0.2 seconds.
If operation is not as specified, replace the relay.
10. Key−off Power Window Signal:
INSPECT DOOR LOCK CONTROL RELAY
HINT:
When the relay circuit is as specified, inspect the key−off power
window signal.
(a) Connect the connector to the relay.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 5 and the negative (−) lead to terminal 11.
(c) Close the door with ignition switch turned to LOCK or
ACC, check that the meter needle indicates battery posi-
tive voltage.
(d) Open the door, check that the meter needle indicates 0 V.
(e) Turn the ignition switch ON, check that the meter needle
indicate battery positive voltage again.
If operation is not as specified, replace the relay.

Downloaded from www.Manualslib.com manuals search engine BE03H−03
Z09299
Left/Light
Adjustment
Switch
Control Switch
Z04379
Z04380
− BODY ELECTRICALPOWER MIRROR CONTROL SYSTEM
BE−57
1996 TOYOTA T100 (RM449U)
INSPECTION
1. INSPECT MIRROR SWITCH CONTINUITY
Left side:
Switch positionTester connectionSpecified condition
UP3 − 4
1 − 8Continuity
DOWN1 − 3
4 − 8Continuity
LEFT3 − 4
1 − 7Continuity
RIGHT1 − 3
4 − 7Continuity
Right side:
Switch positionTester connectionSpecified condition
UP3 − 4
1 − 5Continuity
DOWN1 − 3
4 − 5Continuity
LEFT3 − 4
1 − 6Continuity
RIGHT1 − 3
4 − 6Continuity
If continuity is not as specified, replace the switch.
2. INSPECT MIRROR MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3 and negative (−) lead to terminal 1. Check that the mirror
turns to left side.
(b) Remove the polarity, check that the mirror turns to right
side.

Downloaded from www.Manualslib.com manuals search engine Z04654
Z04382
BE−58
− BODY ELECTRICALPOWER MIRROR CONTROL SYSTEM
1996 TOYOTA T100 (RM449U)
(c) Connect the positive (+) lead from the battery to terminal
2 and the negative (−) lead to terminal 1. Check that the
mirror turns upward.
(d) Reverse the polarity, that the mirror turns downward.
If operation is not as specified, replace the mirror assembly.

Downloaded from www.Manualslib.com manuals search engine BE2826
Cassette Tape Slot Cover
− BODY ELECTRICALAUDIO SYSTEM
BE−61
1861 Author: Date:
1996 TOYOTA T100 (RM449U)
5. ANTI−THEFT SYSTEM
HINT:
The words ”ANTI−THEFT SYSTEM” are displayed on the cas-
sette tape slot cover.
For operation instructions for the anti−theft system, please con-
sult the audio system section in the Owner’s Manual (hereafter
called O/M).
(a) Setting system
The system is in operation once the customer has pushed
the required buttons and entered the customer−selected
3−digit ID number.
(Refer to the O/M section, ”Setting the anti−theft system”)
HINT:
When the audio system is shipped the ID number has not
been input, so the anti−theft system is not in operation.
If the ID number has not been input, the audio system re-
mains the same as a normal audio system.
(b) Anti−theft system operation
If the normal electrical power source (connector or battery
terminal) is cut off, the audio system becomes inoperable,
even if the power supply resumes.
(c) Canceling system
The ID number chosen by the customer is input to cancel
the anti−theft system.
(Refer to the O/M section, ”If the system is activated”)
HINT: To change or cancel the ID number, please refer to
the O/M section ”Canceling the system”.

Downloaded from www.Manualslib.com manuals search engine BE1PK−02
− BODY ELECTRICALANTENNA
BE−81
1881 Author: Date:
1996 TOYOTA T100 (RM449U)
ANTENNA
INSPECTION
1. INSPECT ANTENNA MOTOR
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2.
(b) Check that the motor turns (moves upward).
NOTICE:
These tests must be done quickly (within 3 − 5 seconds) to
prevent the coil from burning out.
(c) Then, reverse the polarity, check that the motor turns the
opposite way (moves downward).
NOTICE:
These tests must be done quickly (within 3 − 5 seconds) to
prevent the coil from burning out.
2. INSPECT ANTENNA MOTOR CONTROL RELAY CIR-
CUIT
Disconnect the connector from the relay and inspect the con-
nector on wire harness side, as shown in the chart below.
Tester connectionConditionSpecified condition
2 − 3ConstantContinuity
6 − GroundConstantContinuity
1 − GroundConstantBattery positive voltage
4 − GroundIgnition switch LOCK or ACCNo voltage
4 − GroundIgnition switch ONBattery positive voltage
5 − GroundIgnition switch LOCKNo voltage
5 − GroundIgnition switch ACC or ONBattery positive voltage
7 − GroundIgnition switch LOCKNo voltage
7 − GroundIgnition switch ACC or ON
(Radio switch and cassette OFF)No voltage
7 − GroundIgnition switch ACC or ON
(Radio switch or cassette ON)Battery positive voltage
8 − GroundIgnition switch LOCKNo voltage
If circuit is as specified, replace the relay.

Downloaded from www.Manualslib.com manuals search engine BE1PL−02
BE4671
Antenna Nut
BE5781
BE5780
BE4674
Twist BE−82
− BODY ELECTRICALANTENNA
1996 TOYOTA T100 (RM449U)
REPLACEMENT
1. REMOVE ANTENNA ROD
HINT:
Perform this operation with negative (−) cable connected to the
battery terminal.
(a) Turn the ignition switch to ”LOCK” position.
(b) Remove the antenna nut.
(c) Press the ”AM” buttons on the radio receiver, and simulta-
neously turn the ignition switch to ”ACC” position.
HINT:
The rod will extend fully and be released from the motor
antenna.
After removing the antenna rod, leave the ignition switch
as ”ACC”.
NOTICE:
To prevent body damage when the antenna rod is released,
hold the rod while it comes out.
2. INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.
HINT:
When inserting the cable, the teeth on the cable must face to-
ward the front of the vehicle.
(b) Wind the cable to retract the rod by turning the ignition
switch to ”LOCK” position.
HINT:
If the ignition switch is already in ”LOCK” position, perform
step 1 (c) first, then turn the ignition switch to ”ACC” posi-
tion.
In case the cable is not wound, twist it as shown in the il-
lustration.
Even if the rod has not retracted fully, install the antenna
nut and inspect the antenna rod operation. It will finally re-
tract fully.
(c) Inspect the antenna rod operation by pushing the radio
wave band select buttons.